SIST EN 300 086 V2.1.2:2016
(Main)Land Mobile Service - Radio equipment with an internal or external RF connector intended primarily for analogue speech- Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
Land Mobile Service - Radio equipment with an internal or external RF connector intended primarily for analogue speech- Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
The present document covers the technical requirements for radio transmitters and receivers used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 1 GHz, with channel
separations of 12,5 kHz, 20 kHz and 25 kHz, primarily intended for analogue speech.
The equipment comprises a transmitter and associated modulator and/or a receiver and associated demodulator. The
types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
and
• those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector, but fitted with a permanent internal or a temporary internal 50 Ω
Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input.
NOTE: Hand portable equipment without an external or internal RF connector and without the possibility of
having a temporary internal 50 Ω RF connector is not covered by the present document (integral antenna
equipment is covered by ETSI EN 300 296 [i.1]).
The present document contains requirements to demonstrate that "... radio equipment shall be so constructed that it both
effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" and that
"....radio equipment supports certain features ensuring access to emergency services" [i.7].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Radio Equipment Directive [i.7] may apply to equipment within the scope of the
present document.
Storitev kopenskih mobilnih komunikacij - Radijska oprema z notranjim ali zunanjim RF-konektorjem, namenjena predvsem za analogni govor - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument zajema tehnične zahteve za radijske oddajnike in sprejemnike, ki se uporabljajo v postajah za storitev zasebnega mobilnega radia (PMR).
Obravnava uporabo storitve kopenskih mobilnih komunikacij, ki deluje prek radijskih frekvenc med 30 MHz in 1 GHz, vključuje medkanalske razmike 12,5 kHz, 20 kHz in 25 kHz ter je namenjena predvsem za analogni govor.
Oprema zajema oddajnik ter ustrezen modulator in/ali sprejemnik ter ustrezen demodulator. Ta dokument zajema naslednje vrste opreme:
• bazna postaja (oprema z antenskim priključkom, namenjena za uporabo na stalni lokaciji);
• mobilna postaja (oprema z antenskim priključkom, ki se običajno uporablja v vozilu ali prenosno);
ter
• prenosne postaje:
a) z antenskim priključkom; ali
b) brez zunanjega antenskega priključka, vendar s stalnim ali začasnim notranjim 50-ohmskim radiofrekvenčnim (RF) konektorjem, ki omogoča dostop do izhoda oddajnika in vhoda sprejemnika.
OPOMBA: Ta dokument ne zajema prenosne opreme brez zunanjega ali notranjega RF-konektorja in brez možnosti namestitve začasnega notranjega 50-ohmskega RF-konektorja (vgrajena antena je obravnavana v standardu ETSI EN 300 296 [i.1]).
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da »... mora biti radijska oprema izdelana tako, da optimalno uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivega motenja« ter da
»radijska oprema podpira določene funkcije, ki zagotavljajo dostop do storitev za nujne primere« [i.7].
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta lahko uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov 3. člena direktive o radijski opremi [i.7].
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.DUPRQL]LUDQL(8Land Mobile Service - Radio equipment with an internal or external RF connector intended primarily for analogue speech- Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU33.070.01Mobilni servisi na splošnoMobile services in general33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 300 086 V2.1.2 (2016-08)SIST EN 300 086 V2.1.2:2016en01-november-2016SIST EN 300 086 V2.1.2:2016SLOVENSKI
STANDARD
SIST EN 300 086 V2.1.2:2016
ETSI EN 300 086 V2.1.2 (2016-08) Land Mobile Service; Radio equipment with an internal or external RF connector intended primarily for analogue speech; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 300 086 V2.1.2:2016
ETSI ETSI EN 300 086 V2.1.2 (2016-08) 2
Reference REN/ERM-TGDMR-351 Keywords analogue, antenna, harmonised standard, mobile, PMR, radio, speech ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 086 V2.1.2:2016
ETSI ETSI EN 300 086 V2.1.2 (2016-08) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 10 3.3 Abbreviations . 11 4 General and operational requirements . 11 4.1 General . 11 4.1.1 Environmental profile . 11 4.1.2 Choice of model for testing . 12 4.1.3 Auxiliary test equipment . 12 4.2 Mechanical and electrical design . 12 4.2.1 General . 12 4.2.2 Controls . 12 4.2.3 Transmitter shut-off facility . 12 5 Test conditions, power sources and ambient temperatures . 12 5.1 Normal and extreme test conditions . 12 5.2 Test power source . 13 5.3 Normal test conditions . 13 5.3.1 Normal temperature and humidity . 13 5.3.2 Normal test power source . 13 5.3.2.1 Mains voltage . 13 5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13 5.3.2.3 Other power sources . 13 5.4 Extreme test conditions . 14 5.4.1 Extreme temperatures . 14 5.4.2 Extreme test source voltages . 14 5.4.2.1 Mains voltage . 14 5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 14 5.4.2.3 Power sources using other types of batteries . 14 5.4.2.4 Other power sources . 14 5.5 Procedure for tests at extreme temperatures . 15 5.5.0 Thermal balance . 15 5.5.1 Procedure for equipment designed for continuous transmission. 15 5.5.2 Procedure for equipment designed for intermittent transmission . 15 5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 15 6 General conditions of measurement . 16 6.1 Arrangements for test signals applied to the receiver input . 16 6.2 Receiver mute or squelch facility . 16 6.3 Artificial antenna . 16 6.4 Test sites and general arrangements for radiated measurements . 16 6.5 Arrangement for test signals at the input of the transmitter . 16 6.6 Receiver rated audio output power . 16 6.7 Tests of equipment with a duplex filter . 16 7 Technical characteristics of the transmitter . 17 7.1 Frequency error . 17 SIST EN 300 086 V2.1.2:2016
ETSI ETSI EN 300 086 V2.1.2 (2016-08) 4 7.1.1 Definition . 17 7.1.2 Method of measurement . 17 7.1.3 Limits . 17 7.2 Transmitter power (conducted) . 18 7.2.1 Definitions . 18 7.2.2 Method of measurement . 18 7.2.3 Limits . 18 7.3 Maximum effective radiated power . 18 7.3.1 Definition . 18 7.3.2 Methods of measurement . 19 7.3.3 Limits . 21 7.4 Frequency deviation . 22 7.4.1 Definition . 22 7.4.2 Method of measurement . 22 7.4.2.1 Maximum permissible frequency deviation . 22 7.4.2.2 Response of the transmitter to modulation frequencies above 3 kHz . 22 7.4.3 Limits . 22 7.4.3.1 Maximum permissible frequency deviation . 22 7.4.3.2 Response of the transmitter to modulation frequencies above 3 kHz . 23 7.5 Adjacent and alternate channel power . 23 7.5.1 Definition . 23 7.5.2 Method of measurement . 24 7.5.3 Limits . 25 7.6 Unwanted emissions in the spurious domain. 25 7.6.1 Definition . 25 7.6.2 Method of measuring the power level . 26 7.6.3 Method of measuring the effective radiated power . 27 7.6.4 Limits . 29 7.7 Intermodulation attenuation. 30 7.7.1 Definition . 30 7.7.2 Method of measurement . 31 7.7.3 Limits . 32 8 Technical characteristics of the receiver . 32 8.1 Maximum usable sensitivity (conducted) . 32 8.1.1 Definition . 32 8.1.2 Method of measurement . 32 8.1.3 Limits . 32 8.2 Maximum usable sensitivity (field strength) . 33 8.2.1 Definition . 33 8.2.2 Method of measurement . 33 8.2.3 Limits . 34 8.3 Co-channel rejection. 34 8.3.1 Definition . 34 8.3.2 Method of measurement . 34 8.3.3 Limits . 34 8.4 Adjacent channel selectivity . 35 8.4.1 Definition . 35 8.4.2 Method of measurement . 35 8.4.3 Limits . 35 8.5 Spurious response rejection . 35 8.5.1 Definition . 35 8.5.2 Introduction to the method of measurement . 36 8.5.3 Method of measurement . 36 8.5.3.1 Method of search over the "limited frequency range" . 36 8.5.3.2 Method of measurement - Step 2 . 37 8.5.4 Limits . 37 8.6 Intermodulation response rejection . 37 8.6.1 Definition . 37 8.6.2 Method of measurement . 37 8.6.3 Limits . 38 8.7 Blocking or desensitization . 38 SIST EN 300 086 V2.1.2:2016
ETSI ETSI EN 300 086 V2.1.2 (2016-08) 5 8.7.1 Definition . 38 8.7.2 Method of measurement . 38 8.7.3 Limits . 38 8.8 Spurious radiations . 39 8.8.1 Definition . 39 8.8.2 Method of measuring the power level . 39 8.8.3 Method of measuring the effective radiated power . 40 8.8.4 Limits . 41 9 Duplex operation . 42 9.1 Receiver desensitization (with simultaneous transmission and reception) . 42 9.1.1 Definition . 42 9.1.2 Method of measurement when the equipment operates with a duplex filter . 42 9.1.3 Measuring method when the equipment operates with two antennas . 42 9.1.4 Limits . 43 9.2 Receiver spurious response rejection (with simultaneous transmission and reception) . 43 9.2.1 Definition . 43 9.2.2 Method of measurement . 43 9.2.3 Limits . 44 10 Testing for compliance with technical requirements . 44 10.1 Test conditions, power supply and ambient temperatures . 44 10.2 Interpretation of the measurement results . 44 Annex A (normative): Radiated measurement . 46 A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 46 A.1.0 General . 46 A.1.1 Anechoic chamber . 46 A.1.2 Anechoic chamber with a conductive ground plane . 47 A.1.3 Open Area Test Site (OATS) . 48 A.1.4 Test antenna . 49 A.1.5 Substitution antenna . 49 A.1.6 Measuring antenna . 50 A.2 Guidance on the use of radiation test sites . 50 A.2.0 General . 50 A.2.1 Verification of the test site . 50 A.2.2 Preparation of the EUT . 50 A.2.3 Power supplies to the EUT . 50 A.2.4 Volume control setting for analogue speech tests . 50 A.2.5 Range length . 51 A.2.6 Site preparation . 51 A.3 Coupling of signals . 52 A.3.1 General . 52 A.3.2 Data signals . 52 A.3.3 Speech and analogue signals . 52 A.3.3.0 General . 52 A.3.3.1 Acoustic coupler description. 52 A.3.3.2 Calibration . 53 Annex B (normative): Specification for some particular measurement arrangements . 54 B.1 Power measuring receiver specification . 54 B.1.0 Description . 54 B.1.1 IF filter . 54 B.1.2 Attenuation indicator . 55 B.1.3 RMS value indicator . 55 B.1.4 Oscillator and amplifier . 55 B.2 Spectrum analyser specification . 56 B.2.1 Adjacent and alternate channel power measurement . 56 B.2.2 Unwanted emissions measurement . 56 SIST EN 300 086 V2.1.2:2016
ETSI ETSI EN 300 086 V2.1.2 (2016-08) 6 B.3 Integrating and power summing device .
...
ETSI EN 300 086 V2.1.2 (2016-08)
HARMONISED EUROPEAN STANDARD
Land Mobile Service;
Radio equipment with an internal or external RF
connector intended primarily for analogue speech;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 300 086 V2.1.2 (2016-08)
Reference
REN/ERM-TGDMR-351
Keywords
analogue, antenna, harmonised standard, mobile,
PMR, radio, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 086 V2.1.2 (2016-08)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 11
4 General and operational requirements . 11
4.1 General . 11
4.1.1 Environmental profile . 11
4.1.2 Choice of model for testing . 12
4.1.3 Auxiliary test equipment . 12
4.2 Mechanical and electrical design . 12
4.2.1 General . 12
4.2.2 Controls . 12
4.2.3 Transmitter shut-off facility . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 13
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal test power source . 13
5.3.2.1 Mains voltage . 13
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 14
5.4.1 Extreme temperatures . 14
5.4.2 Extreme test source voltages . 14
5.4.2.1 Mains voltage . 14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 14
5.4.2.3 Power sources using other types of batteries . 14
5.4.2.4 Other power sources . 14
5.5 Procedure for tests at extreme temperatures . 15
5.5.0 Thermal balance . 15
5.5.1 Procedure for equipment designed for continuous transmission. 15
5.5.2 Procedure for equipment designed for intermittent transmission . 15
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 15
6 General conditions of measurement . 16
6.1 Arrangements for test signals applied to the receiver input . 16
6.2 Receiver mute or squelch facility . 16
6.3 Artificial antenna . 16
6.4 Test sites and general arrangements for radiated measurements . 16
6.5 Arrangement for test signals at the input of the transmitter . 16
6.6 Receiver rated audio output power . 16
6.7 Tests of equipment with a duplex filter . 16
7 Technical characteristics of the transmitter . 17
7.1 Frequency error . 17
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 086 V2.1.2 (2016-08)
7.1.1 Definition . 17
7.1.2 Method of measurement . 17
7.1.3 Limits . 17
7.2 Transmitter power (conducted) . 18
7.2.1 Definitions . 18
7.2.2 Method of measurement . 18
7.2.3 Limits . 18
7.3 Maximum effective radiated power . 18
7.3.1 Definition . 18
7.3.2 Methods of measurement . 19
7.3.3 Limits . 21
7.4 Frequency deviation . 22
7.4.1 Definition . 22
7.4.2 Method of measurement . 22
7.4.2.1 Maximum permissible frequency deviation . 22
7.4.2.2 Response of the transmitter to modulation frequencies above 3 kHz . 22
7.4.3 Limits . 22
7.4.3.1 Maximum permissible frequency deviation . 22
7.4.3.2 Response of the transmitter to modulation frequencies above 3 kHz . 23
7.5 Adjacent and alternate channel power . 23
7.5.1 Definition . 23
7.5.2 Method of measurement . 24
7.5.3 Limits . 25
7.6 Unwanted emissions in the spurious domain. 25
7.6.1 Definition . 25
7.6.2 Method of measuring the power level . 26
7.6.3 Method of measuring the effective radiated power . 27
7.6.4 Limits . 29
7.7 Intermodulation attenuation. 30
7.7.1 Definition . 30
7.7.2 Method of measurement . 31
7.7.3 Limits . 32
8 Technical characteristics of the receiver . 32
8.1 Maximum usable sensitivity (conducted) . 32
8.1.1 Definition . 32
8.1.2 Method of measurement . 32
8.1.3 Limits . 32
8.2 Maximum usable sensitivity (field strength) . 33
8.2.1 Definition . 33
8.2.2 Method of measurement . 33
8.2.3 Limits . 34
8.3 Co-channel rejection. 34
8.3.1 Definition . 34
8.3.2 Method of measurement . 34
8.3.3 Limits . 34
8.4 Adjacent channel selectivity . 35
8.4.1 Definition . 35
8.4.2 Method of measurement . 35
8.4.3 Limits . 35
8.5 Spurious response rejection . 35
8.5.1 Definition . 35
8.5.2 Introduction to the method of measurement . 36
8.5.3 Method of measurement . 36
8.5.3.1 Method of search over the "limited frequency range" . 36
8.5.3.2 Method of measurement - Step 2 . 37
8.5.4 Limits . 37
8.6 Intermodulation response rejection . 37
8.6.1 Definition . 37
8.6.2 Method of measurement . 37
8.6.3 Limits . 38
8.7 Blocking or desensitization . 38
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 086 V2.1.2 (2016-08)
8.7.1 Definition . 38
8.7.2 Method of measurement . 38
8.7.3 Limits . 38
8.8 Spurious radiations . 39
8.8.1 Definition . 39
8.8.2 Method of measuring the power level . 39
8.8.3 Method of measuring the effective radiated power . 40
8.8.4 Limits . 41
9 Duplex operation . 42
9.1 Receiver desensitization (with simultaneous transmission and reception) . 42
9.1.1 Definition . 42
9.1.2 Method of measurement when the equipment operates with a duplex filter . 42
9.1.3 Measuring method when the equipment operates with two antennas . 42
9.1.4 Limits . 43
9.2 Receiver spurious response rejection (with simultaneous transmission and reception) . 43
9.2.1 Definition . 43
9.2.2 Method of measurement . 43
9.2.3 Limits . 44
10 Testing for compliance with technical requirements . 44
10.1 Test conditions, power supply and ambient temperatures . 44
10.2 Interpretation of the measurement results . 44
Annex A (normative): Radiated measurement . 46
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 46
A.1.0 General . 46
A.1.1 Anechoic chamber . 46
A.1.2 Anechoic chamber with a conductive ground plane . 47
A.1.3 Open Area Test Site (OATS) . 48
A.1.4 Test antenna . 49
A.1.5 Substitution antenna . 49
A.1.6 Measuring antenna . 50
A.2 Guidance on the use of radiation test sites . 50
A.2.0 General . 50
A.2.1 Verification of the test site . 50
A.2.2 Preparation of the EUT . 50
A.2.3 Power supplies to the EUT . 50
A.2.4 Volume control setting for analogue speech tests . 50
A.2.5 Range length . 51
A.2.6 Site preparation . 51
A.3 Coupling of signals . 52
A.3.1 General . 52
A.3.2 Data signals . 52
A.3.3 Speech and analogue signals . 52
A.3.3.0 General . 52
A.3.3.1 Acoustic coupler description. 52
A.3.3.2 Calibration . 53
Annex B (normative): Specification for some particular measurement arrangements . 54
B.1 Power measuring receiver specification . 54
B.1.0 Description . 54
B.1.1 IF filter . 54
B.1.2 Attenuation indicator . 55
B.1.3 RMS value indicator . 55
B.1.4 Oscillator and amplifier . 55
B.2 Spectrum analyser specification . 56
B.2.1 Adjacent and alternate channel power measurement . 56
B.2.2 Unwanted emissions measurement . 56
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 086 V2.1.2 (2016-08)
B.3 Integrating and power summing device . 56
Annex C (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 57
Histor
...
Final draft ETSI EN 300 086 V2.1.1 (2016-06)
HARMONISED EUROPEAN STANDARD
Land Mobile Service;
Radio equipment with an internal or external RF
connector intended primarily for analogue speech;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 086 V2.1.1 (2016-06)
Reference
REN/ERM-TGDMR-351
Keywords
analogue, antenna, mobile, PMR, radio, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 086 V2.1.1 (2016-06)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 11
4 General and operational requirements . 11
4.1 General . 11
4.1.1 Environmental profile . 11
4.1.2 Choice of model for testing . 11
4.1.3 Auxiliary test equipment . 12
4.2 Mechanical and electrical design . 12
4.2.1 General . 12
4.2.2 Controls . 12
4.2.3 Transmitter shut-off facility . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 13
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal test power source . 13
5.3.2.1 Mains voltage . 13
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 14
5.4.1 Extreme temperatures . 14
5.4.2 Extreme test source voltages . 14
5.4.2.1 Mains voltage . 14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 14
5.4.2.3 Power sources using other types of batteries . 14
5.4.2.4 Other power sources . 14
5.5 Procedure for tests at extreme temperatures . 15
5.5.0 Thermal balance . 15
5.5.1 Procedure for equipment designed for continuous transmission. 15
5.5.2 Procedure for equipment designed for intermittent transmission . 15
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 15
6 General conditions of measurement . 16
6.1 Arrangements for test signals applied to the receiver input . 16
6.2 Receiver mute or squelch facility . 16
6.3 Artificial antenna . 16
6.4 Test sites and general arrangements for radiated measurements . 16
6.5 Arrangement for test signals at the input of the transmitter . 16
6.6 Receiver rated audio output power . 16
6.7 Tests of equipment with a duplex filter . 16
7 Technical characteristics of the transmitter . 17
7.1 Frequency error . 17
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 086 V2.1.1 (2016-06)
7.1.1 Definition . 17
7.1.2 Method of measurement . 17
7.1.3 Limits . 17
7.2 Transmitter power (conducted) . 18
7.2.1 Definitions . 18
7.2.2 Method of measurement . 18
7.2.3 Limits . 18
7.3 Maximum effective radiated power . 18
7.3.1 Definition . 18
7.3.2 Methods of measurement . 19
7.3.3 Limits . 21
7.4 Frequency deviation . 22
7.4.1 Definition . 22
7.4.2 Method of measurement . 22
7.4.2.1 Maximum permissible frequency deviation . 22
7.4.2.2 Response of the transmitter to modulation frequencies above 3 kHz . 22
7.4.3 Limits . 22
7.4.3.1 Maximum permissible frequency deviation . 22
7.4.3.2 Response of the transmitter to modulation frequencies above 3 kHz . 23
7.5 Adjacent and alternate channel power . 23
7.5.1 Definition . 23
7.5.2 Method of measurement . 24
7.5.3 Limits . 25
7.6 Unwanted emissions in the spurious domain. 25
7.6.1 Definition . 25
7.6.2 Method of measuring the power level . 26
7.6.3 Method of measuring the effective radiated power . 27
7.6.4 Limits . 29
7.7 Intermodulation attenuation. 30
7.7.1 Definition . 30
7.7.2 Method of measurement . 31
7.7.3 Limits . 32
8 Technical characteristics of the receiver . 32
8.1 Maximum usable sensitivity (conducted) . 32
8.1.1 Definition . 32
8.1.2 Method of measurement . 32
8.1.3 Limits . 32
8.2 Maximum usable sensitivity (field strength) . 33
8.2.1 Definition . 33
8.2.2 Method of measurement . 33
8.2.3 Limits . 34
8.3 Co-channel rejection. 34
8.3.1 Definition . 34
8.3.2 Method of measurement . 34
8.3.3 Limits . 34
8.4 Adjacent channel selectivity . 35
8.4.1 Definition . 35
8.4.2 Method of measurement . 35
8.4.3 Limits . 35
8.5 Spurious response rejection . 35
8.5.1 Definition . 35
8.5.2 Introduction to the method of measurement . 36
8.5.3 Method of measurement . 36
8.5.3.1 Method of search over the "limited frequency range" . 36
8.5.3.2 Method of measurement - Step 2 . 37
8.5.4 Limits . 37
8.6 Intermodulation response rejection . 37
8.6.1 Definition . 37
8.6.2 Method of measurement . 37
8.6.3 Limits . 38
8.7 Blocking or desensitization . 38
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 086 V2.1.1 (2016-06)
8.7.1 Definition . 38
8.7.2 Method of measurement . 38
8.7.3 Limits . 38
8.8 Spurious radiations . 39
8.8.1 Definition . 39
8.8.2 Method of measuring the power level . 39
8.8.3 Method of measuring the effective radiated power . 40
8.8.4 Limits . 41
9 Duplex operation . 42
9.1 Receiver desensitization (with simultaneous transmission and reception) . 42
9.1.1 Definition . 42
9.1.2 Method of measurement when the equipment operates with a duplex filter . 42
9.1.3 Measuring method when the equipment operates with two antennas . 42
9.1.4 Limits . 43
9.2 Receiver spurious response rejection (with simultaneous transmission and reception) . 43
9.2.1 Definition . 43
9.2.2 Method of measurement . 43
9.2.3 Limits . 44
10 Testing for compliance with technical requirements . 44
10.1 Test conditions, power supply and ambient temperatures . 44
10.2 Interpretation of the measurement results . 44
Annex A (normative): Radiated measurement . 46
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 46
A.1.0 General . 46
A.1.1 Anechoic chamber . 46
A.1.2 Anechoic chamber with a conductive ground plane . 47
A.1.3 Open Area Test Site (OATS) . 48
A.1.4 Test antenna . 49
A.1.5 Substitution antenna . 49
A.1.6 Measuring antenna . 50
A.2 Guidance on the use of radiation test sites . 50
A.2.0 General . 50
A.2.1 Verification of the test site . 50
A.2.2 Preparation of the EUT . 50
A.2.3 Power supplies to the EUT . 50
A.2.4 Volume control setting for analogue speech tests . 50
A.2.5 Range length . 51
A.2.6 Site preparation . 51
A.3 Coupling of signals . 52
A.3.1 General . 52
A.3.2 Data signals . 52
A.3.3 Speech and analogue signals . 52
A.3.3.0 General . 52
A.3.3.1 Acoustic coupler description. 52
A.3.3.2 Calibration . 53
Annex B (normative): Specification for some particular measurement arrangements . 54
B.1 Power measuring receiver specification . 54
B.1.0 Description . 54
B.1.1 IF filter . 54
B.1.2 Attenuation indicator . 55
B.1.3 RMS value indicator . 55
B.1.4 Oscillator and amplifier . 55
B.2 Spectrum analyser specification . 56
B.2.1 Adjacent and alternate channel power measurement . 56
B.2.2 Unwanted emissions measurement . 56
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 086 V2.1.1 (2016-06)
B.3 Integrating and power summing device . 56
Annex C (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.