Light conveyor belts - Determination of the relaxed elastic modulus (ISO 21181:2013)

This International Standard specifies a test method for the determination of the relaxed elastic modulus of light conveyor belts according to ISO 21183-1 or other conveyor belts where ISO 9856 is not applicable.

Leichte Fördergurte - Bestimmung des relaxierten Elastizitätsmoduls (ISO 21181:2013)

Diese Internationale Norm legt ein Prüfverfahren fest für die Bestimmung des relaxierten Elastizitätsmoduls von leichten Fördergurten nach ISO 21183 1 oder von anderen Fördergurten, für die ISO 9856 nicht anwendbar ist.

Courroies transporteuses légères - Détermination du module d'élasticité relaxé (ISO 21181:2013)

L'ISO 21181:2013 spécifie une méthode d'essai permettant de déterminer le module d'élasticité relaxé des courroies transporteuses légères selon l'ISO 21183-1, ou d'autres courroies transporteuses lorsque l'ISO 9856 n'est pas applicable.

Naprave za kontinuirni transport - Lahki trakovi tračnih transporterjev - Ugotavljanje trajnega (relaksiranega) elastičnega modula traka (ISO 21181:2013)

Ta mednarodni standard določa preskusno metodo za ugotavljanje trajnega (relaksiranega) elastičnega modula lahkih trakov tračnih transporterjev v skladu s standardom ISO 21183-1 ali drugih trakov tračnih transporterjev, za katere se standard ISO 9856 ne uporablja.

General Information

Status
Published
Public Enquiry End Date
31-Dec-2012
Publication Date
13-May-2013
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
11-Apr-2013
Due Date
16-Jun-2013
Completion Date
14-May-2013

RELATIONS

Buy Standard

Standard
SIST EN ISO 21181:2013
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 21181:2013
01-junij-2013
1DGRPHãþD
SIST EN ISO 21181:2007
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW/DKNLWUDNRYLWUDþQLKWUDQVSRUWHUMHY
8JRWDYOMDQMHWUDMQHJD UHODNVLUDQHJD HODVWLþQHJDPRGXODWUDND ,62

Light conveyor belts - Determination of the relaxed elastic modulus (ISO 21181:2013)

Leichte Fördergurte - Bestimmung des relaxierten Elastizitätsmoduls (ISO 21181:2013)

Courroies transporteuses légères - Détermination du module d'élasticité relaxé (ISO

21181:2013)
Ta slovenski standard je istoveten z: EN ISO 21181:2013
ICS:
53.040.10 Transporterji Conveyors
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 21181:2013 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 21181:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 21181:2013
EUROPEAN STANDARD
EN ISO 21181
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2013
ICS 53.040.20 Supersedes EN ISO 21181:2006
English Version
Light conveyor belts - Determination of the relaxed elastic
modulus (ISO 21181:2013)
Courroies transporteuses légères - Détermination du
module d'élasticité relaxé (ISO 21181:2013)
This European Standard was approved by CEN on 12 February 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national

standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same

status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United

Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21181:2013: E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 21181:2013
EN ISO 21181:2013 (E)
Contents Page

Foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 21181:2013
EN ISO 21181:2013 (E)
Foreword

This document (EN ISO 21181:2013) has been prepared by Technical Committee ISO/TC 41 "Pulleys and

belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the

secretariat of which is held by SNV.

This European Standard shall be given the status of a national standard, either by publication of an identical

text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at

the latest by August 2013.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 21181:2006.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following

countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech

Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,

Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

Endorsement notice

The text of ISO 21181:2013 has been approved by CEN as EN ISO 21181:2013 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 21181:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 21181:2013
INTERNATIONAL ISO
STANDARD 21181
Second edition
2013-02-15
Light conveyor belts — Determination
of the relaxed elastic modulus
Courroies transporteuses légères — Détermination du module
d’élasticité relaxé
Reference number
ISO 21181:2013(E)
ISO 2013
---------------------- Page: 7 ----------------------
SIST EN ISO 21181:2013
ISO 21181:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 21181:2013
ISO 21181:2013(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Symbols .......................................................................................................................................................................................................................... 2

5 Principle ........................................................................................................................................................................................................................ 2

6 Apparatus ..................................................................................................................................................................................................................... 2

7 Test pieces ................................................................................................................................................................................................................... 2

7.1 Shape, dimensions, number and selection ...................................................................................................................... 2

7.2 Conditioning .............................................................................................................................................................................................. 3

8 Procedure..................................................................................................................................................................................................................... 3

9 Calculation and expression of results ............................................................................................................................................. 4

10 Test report ................................................................................................................................................................................................................... 6

Bibliography ................................................................................................................................................................................................................................ 7

© ISO 2013 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 21181:2013
ISO 21181:2013(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International

Standards adopted by the technical committees are circulated to the member bodies for voting.

Publication as an International Standard requires approval by at least 75 % of the member bodies

casting a vote.

ISO 21181 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts),

Subcommittee SC 3, Conveyor belts.
This International Standard is based on EN 1723:1999, prepared by CEN/TC 188.

This second edition cancels and replaces the first edition (ISO 21181:2005), of which it constitutes a

minor revision.
iv © ISO 2013 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 21181:2013
ISO 21181:2013(E)
Introduction

Many applications for light conveyor belts require that the belt is initially tensioned and there is no

subsequent change in belt length by adjustment of any rollers. In such cases, the tensioning force in the

belt changes throughout the life of the belt because of two effects: permanent stretch and relaxation

of the belt, both of which change its real elastic modulus. It is vital to have a means of establishing

the way in which the tensioning forces change; and this test applies a cy
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.