SIST EN IEC 61439-7:2021
(Main)Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations (IEC 61439-7:2018+COR1:2019)
Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations (IEC 61439-7:2018+COR1:2019)
IEC 61439-7:2018 defines the specific requirements of assemblies as follows:
- assemblies for which the rated voltage does not exceed 1 000 V in the case of AC or 1 500 V in the case of DC;
– assemblies intended for use in connection with the generation, transmission, distribution and conversion of electric energy, and for the control of electric energy consuming equipment;
– assemblies operated by ordinary persons (e.g. plug and unplug of electrical equipment);
– assemblies intended to be installed and used in market squares, marinas, campsites and other similar outdoor public sites;
– assemblies intended for charging stations for electric vehicles (AEVCS) for Mode 3 and Mode 4. They are designed to integrate the functionality and additional requirements for electric vehicle conductive charging systems according to IEC 61851-1:2017.
This first edition cancels and replaces the relevant technical specification published in 2014. It constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous technical specification:
a new classification of the stationary ASSEMBLIES in accordance with their mechanical resistance (5.702);
a new Table 702 with the list of tests and relevant severities to which the ASSEMBLIES have to be subjected according to the classification mentioned at point a);
a new Annex (CC) with a new endurance test for the individual switching devices intended to be used in AEVSC, if they have not already been tested against this requirement;
a general editorial review and a technical revision.
The contents of the corrigendum of August 2019 have been included in this copy.
Niederspannungs-Schaltgerätekombinationen - Teil 7: Schaltgerätekombinationen für bestimmte Anwendungen wie Marinas, Campingplätze, Marktplätze, Ladestationen für Elektrofahrzeuge (IEC 61439-7:2018+COR1:2019)
Ensembles d’appareillage à basse tension - Partie 7: Ensembles pour installations publiques particulières telles que les marinas, les terrains de camping, les marchés et les emplacements analogues et pour bornes de charge de véhicules électriques (IEC 61439-7:2018+COR1:2019)
L’Article 1 de l’IEC 61439-1:2011 s’applique avec les exceptions suivantes.
Remplacement:
NOTE 1 Dans l’ensemble du présent document, les termes AMHS (voir 3.1.701), ACCS (voir 3.1.702), AMPS (voir 3.1.703), AEVCS (voir 3.1.704) sont utilisés pour désigner les ensembles d’appareillage à basse tension destinés à être utilisés respectivement dans les marinas et emplacements analogues (AMHS), terrains de camping et emplacements analogues (ACCS), marchés et autres lieux publics extérieurs analogues (AMPS), et les bornes de charge (AEVCS). Le terme ENSEMBLES est utilisé pour indiquer tous ces types de tableaux.
La présente partie de l'IEC 61439 définit les exigences spécifiques applicables aux ENSEMBLES comme suit:
- ENSEMBLES dont la tension assignée ne dépasse pas 1 000 V en courant alternatif ou 1 500 V en courant continu;
- ENSEMBLES destinés à être utilisés avec des équipements conçus pour la production, le transport, la distribution et la conversion de l'énergie électrique et la commande des matériels consommant de l'énergie électrique;
- ENSEMBLES actionnés par des personnes ordinaires (par exemple, brancher ou débrancher du matériel électrique);
- ENSEMBLES destinés à être installés et utilisés dans les marchés, marinas, terrains de camping et autres lieux publics extérieurs analogues;
- ENSEMBLES destinés aux bornes de charge de véhicules électriques (AEVCS) de Mode 3 et de Mode 4. Ils sont conçus pour intégrer la fonctionnalité et les exigences supplémentaires des systèmes de charge conductive pour véhicules électriques conformément à l’IEC 61851-1:2017.
Pour le CHOIX approprié des appareils de connexion et des composants, les normes suivantes s'appliquent:
- IEC 60364-7-709 (AMHS) OU
- IEC 60364-7-708 (ACCS) OU
- IEC 60364-7-740 (AMPS) OU
- IEC 60364-7-722 (AEVCS).
Le présent document s’applique à tous les ENSEMBLES qu’ils soient conçus, fabriqués et vérifiés à l’unité ou qu’ils soient complètement normalisés et fabriqués en quantité.
La fabrication et/ou l’assemblage peuvent être réalisé(e)s par un tiers qui n'est pas le constructeur d'origine (voir 3.10.1 de l’IEC 61439-1:2011).
Le présent document ne s’applique pas aux appareils pris en considération individuellement et aux composants indépendants tels que les disjoncteurs, les fusibles-interrupteurs, les matériels électroniques, qui sont conformes aux normes de produits les concernant.
NOTE 2 Lorsque le matériel électrique est directement raccordé au réseau d’alimentation public à basse tension et équipé d’un compteur de facturation du prestataire légal du fournisseur de l’alimentation basse tension, des exigences particulières supplémentaires fondées sur des réglementations nationales s’appliquent, le cas échéant.
Le présent document ne s’applique pas aux boîtes et enceintes pour appareillage électrique pour installations électriques fixes pour usages domestiques et analogues telles que définies dans l'IEC 60670-24.
Sestavi nizkonapetostnih stikalnih in krmilnih naprav - 7. del: Sestavi za posebno uporabo, na primer za marine, prostore za kampiranje, tržnice, napajalne postaje za električna vozila (IEC 61439-7:2018+COR1:2019)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 61439-7:2021
01-februar-2021
Sestavi nizkonapetostnih stikalnih in krmilnih naprav - 7. del: Sestavi za posebno
uporabo, na primer za marine, prostore za kampiranje, tržnice, napajalne postajeza električna vozila (IEC 61439-7:2018+COR1:2019)
Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific
applications such as marinas, camping sites, market squares, electric vehicle charging
stations (IEC 61439-7:2018+COR1:2019)Niederspannungs-Schaltgerätekombinationen - Teil 7: Schaltgerätekombinationen für
bestimmte Anwendungen wie Marinas, Campingplätze, Marktplätze, Ladestationen fürElektrofahrzeuge (IEC 61439-7:2018+COR1:2019)
Ensembles d’appareillage à basse tension - Partie 7: Ensembles pour installations
publiques particulières telles que les marinas, les terrains de camping, les marchés et
les emplacements analogues et pour bornes de charge de véhicules électriques (IEC
61439-7:2018+COR1:2019)Ta slovenski standard je istoveten z: EN IEC 61439-7:2020
ICS:
29.130.20 Nizkonapetostne stikalne in Low voltage switchgear and
krmilne naprave controlgear
SIST EN IEC 61439-7:2021 de,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------SIST EN IEC 61439-7:2021
---------------------- Page: 2 ----------------------
SIST EN IEC 61439-7:2021
EUROPEAN STANDARD EN IEC 61439-7
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2020
ICS 29.130.20
English Version
Low-voltage switchgear and controlgear assemblies - Part 7:
Assemblies for specific applications such as marinas, camping
sites, market squares, electric vehicle charging stations
(IEC 61439-7:2018 + COR1:2019)
Ensembles d'appareillage à basse tension - Partie 7: Niederspannungs-Schaltgerätekombinationen - Teil 7:
Ensembles pour installations publiques particulières telles Schaltgerätekombinationen für bestimmte Anwendungen
que les marinas, les terrains de camping, les marchés et les wie Marinas, Campingplätze, Marktplätze, Ladestationen für
emplacements analogues et pour bornes de charge de Elektrofahrzeugevéhicules électriques (IEC 61439-7:2018 + COR1:2019)
(IEC 61439-7:2018 + COR1:2019)
This European Standard was approved by CENELEC on 2019-01-10. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61439-7:2020 E---------------------- Page: 3 ----------------------
SIST EN IEC 61439-7:2021
EN IEC 61439-7:2020 (E)
European foreword
The text of document 121B/74/FDIS, future edition 1 of IEC 61439-7, prepared by SC 121B "Low-
voltage switchgear and controlgear assemblies" of IEC/TC 121 "Switchgear and controlgear and their
assemblies for low voltage" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61439-7:2020.The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-11-01
level by publication of an identical national standard or by endorsement• latest date by which the national standards conflicting with the (dow) 2023-05-01
document have to be withdrawnAttention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association.Endorsement notice
The text of the International Standard IEC 61439-7:2018 was approved by CENELEC as a European
Standard without any modification.In the official version, for Bibliography, the following notes have to be added for the standards
indicated:IEC 60364-7-708 NOTE Harmonized as HD 60364-7-708
IEC 60364-7-709 NOTE Harmonized as HD 60364-7-709
IEC 60364-7-722 NOTE Harmonized as HD 60364-7-722
IEC 60364-7-740 NOTE Harmonized as HD 60364-7-740
IEC 60670-24 NOTE Harmonized as EN 60670-24
IEC 61439-3 NOTE Harmonized as EN 61439-3
IEC 61851-1:2017 NOTE Harmonized as EN IEC 61851-1:2019 (not modified)
IEC 61851-23 NOTE Harmonized as EN 61851-23
---------------------- Page: 4 ----------------------
SIST EN IEC 61439-7:2021
EN IEC 61439-7:2020 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.Clause 2 of IEC 61439-1:2011 is applicable except as follows.
Addition:
Publication Year Title EN/HD Year
IEC 60068-2-27 - Environmental testing - Part 2-27: Tests - Test Ea EN 60068-2-27 -
and guidance: ShockIEC 60068-2-75 - Environmental testing - Part 2-75: Tests - Test Eh: EN 60068-2-75 -
Hammer testsIEC 61439-1 2011 Low-voltage switchgear and controlgear EN 61439-1 2011
assemblies - Part 1: General rules
---------------------- Page: 5 ----------------------
SIST EN IEC 61439-7:2021
---------------------- Page: 6 ----------------------
SIST EN IEC 61439-7:2021
IEC 61439-7
Edition 1.0 2018-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Low-voltage switchgear and controlgear assemblies –
Part 7: Assemblies for specific applications such as marinas, camping sites,
market squares, electric vehicle charging stations
Ensembles d’appareillage à basse tension –
Partie 7: Ensembles pour installations publiques particulières telles que les
marinas, les terrains de camping, les marchés et les emplacements analogues
et pour bornes de charge de véhicules électriques
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.130.20 ISBN 978-2-8322-6335-8
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical CommissionMarque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 61439-7:2021
– 2 – IEC 61439-7:2018 © IEC 2018
CONTENTS
FOREWORD ........................................................................................................................... 3
1 Scope .............................................................................................................................. 5
2 Normative references ...................................................................................................... 6
3 Terms and definitions ...................................................................................................... 6
4 Symbols and abbreviations .............................................................................................. 8
5 Interface characteristics .................................................................................................. 9
6 Information .................................................................................................................... 12
7 Service conditions ......................................................................................................... 13
8 Constructional requirements .......................................................................................... 13
9 Performance requirements ............................................................................................ 15
10 Design verification ......................................................................................................... 15
11 Routine verification ........................................................................................................ 24
Annexes ............................................................................................................................... 25
Annex AA (informative) Items subject to agreement between the ASSEMBLYmanufacturer and the user .................................................................................................... 26
Annex BB (informative) Design verification .......................................................................... 30
Annex CC (normative) Endurance of the individual switching device .................................... 31
Annex DD (informative) Examples of ASSEMBLIES in accordance with 5.701.1.1 .................... 35
Annex EE (informative) List of notes concerning certain countries ....................................... 36
Bibliography .......................................................................................................................... 38
Figure 701 – Diagram of test to verify the resistance to static load ........................................ 17
Figure 702 – Diagram of test to verify the mechanical strength of doors ................................ 18
Figure 703 – Sandbag for test to verify the resistance to shock load ..................................... 19
Figure 704 – Diagram of test to verify resistance to shock load ............................................. 20
Figure 705 – Diagram of test to verify resistance to torsional stress ...................................... 22
Figure 706 – Striker element for test of resistance to mechanical shock impactsinduced by sharp-edged objects............................................................................................ 23
Figure CC.1 – Test circuit for endurance of the individual switching device test .................... 33
Figure CC.2 – Informative wave shape of inrush current for tests in accordance with
Annex CC ............................................................................................................................. 34
Figure DD.1 – Examples of ASSEMBLIES according to 5.701.1.1 ............................................. 35
Table 701 – Values of assumed loading .................................................................................. 9
Table 702 – Mechanical tests................................................................................................ 11
Table AA.1 – Items subject to agreement between the ASSEMBLY manufacturer and the
user ...................................................................................................................................... 26
Table BB.1 – List of design verifications to be performed ...................................................... 30
---------------------- Page: 8 ----------------------SIST EN IEC 61439-7:2021
IEC 61439-7:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES –
Part 7: Assemblies for specific applications such as marinas, camping
sites, market squares, electric vehicle charging stations
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61439-7 has been prepared by subcommittee 121B: Low-voltage
switchgear and controlgear assemblies, of IEC technical committee 121: Switchgear and
controlgear and their assemblies for low voltage.This first edition cancels and replaces the relevant technical specification published in 2014. It
constitutes a technical revision.This edition includes the following significant technical changes with respect to the previous
technical specification:a) a new classification of the stationary ASSEMBLIES in accordance with their mechanical
resistance (5.702);b) a new Table 702 with the list of tests and relevant severities to which the ASSEMBLIES have
to be subjected according to the classification mentioned at point a);---------------------- Page: 9 ----------------------
SIST EN IEC 61439-7:2021
– 4 – IEC 61439-7:2018 © IEC 2018
c) a new Annex (CC) with a new endurance test for the individual switching devices intended
to be used in AEVSC, if they have not already been tested against this requirement;
d) a general editorial review and a technical revision.The text of this standard is based on the following documents:
FDIS Report on voting
121B/74/FDIS 121B/77/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.This standard is to be read in conjunction with IEC 61439-1:2011. The provisions of the
general rules dealt with in IEC 61439-1:2011 are applicable to this standard where they are
specifically cited. When this document states "addition", "modification" or "replacement", the
relevant text in IEC 61439-1:2011 is to be adapted accordingly.Subclauses that are numbered with a 701 (702, 703, etc.) suffix are additional to the same
subclause in IEC 61439-1:2011.Tables and figures in this document that are new are numbered starting with 701.
New annexes in this document are lettered AA, BB, etc.
In this standard, the term ASSEMBLY written in small capitals is defined in 3.1.1 of IEC 61439-
1:2011.The reader’s attention is drawn to the fact that Annex EE lists all of the "in-some-country"
clauses on differing practices of a less permanent nature relating to the subject of this
standardA list of all parts of the IEC 61439 series, under the general title Low-voltage switchgear and
controlgear assemblies, can be found on the IEC website.This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
The contents of the corrigendum of August 2019 have been included in this copy.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correctunderstanding of its contents. Users should therefore print this document using a
colour printer.---------------------- Page: 10 ----------------------
SIST EN IEC 61439-7:2021
IEC 61439-7:2018 © IEC 2018 – 5 –
LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES –
Part 7: Assemblies for specific applications such as marinas, camping
sites, market squares, electric vehicle charging stations
1 Scope
Clause 1 of IEC 61439-1:2011 is applicable except as follows.
Replacement:
NOTE 1 Throughout this document, the terms AMHS (see 3.1.701), ACCS (see 3.1.702), AMPS (see 3.1.703),
AEVCS (see 3.1.704) are used for low-voltage switchgear and controlgear assemblies intended for use respectively
in marinas and similar locations (AMHS), campsites and similar locations (ACCS), market squares and other similar
external public sites (AMPS) and charging stations (AEVCS). The term ASSEMBLIES is used for indicating all
these boards.This Part of IEC 61439 defines the specific requirements of ASSEMBLIES as follows:
– ASSEMBLIES for which the rated voltage does not exceed 1 000 V in the case of AC or
1 500 V in the case of DC;– ASSEMBLIES intended for use in connection with the generation, transmission, distribution
and conversion of electric energy, and for the control of electric energy consuming
equipment;– ASSEMBLIES operated by ordinary persons (e.g. plug and unplug of electrical equipment);
– ASSEMBLIES intended to be installed and used in market squares, marinas, campsites and
other similar outdoor public sites;– ASSEMBLIES intended for charging stations for electric vehicles (AEVCS) for Mode 3 and
Mode 4. They are designed to integrate the functionality and additional requirements for
electric vehicle conductive charging systems according to IEC 61851-1:2017.For the correct SELECTION of the switching devices and components, the following standards
apply:– IEC 60364-7-709 (AMHS) OR
– IEC 60364-7-708 (ACCS) OR
– IEC 60364-7-740 (AMPS) OR
– IEC 60364-7-722 (AEVCS).
This document applies to all ASSEMBLIES whether they are designed, manufactured and
verified on a one-off basis or fully standardised and manufactured in quantity.The manufacture and/or assembly may be carried out other than by the original manufacturer
(see 3.10.1 of IEC 61439-1:2011).This document does not apply to individual devices and self-contained components such as
circuit breakers, fuse switches, electronic equipment, which comply with their relevant product
standards.NOTE 2 Where electrical equipment is directly connected to public low voltage supply system and equipped with
a meter for billing of the legal provider of the low voltage supply, additional particular requirements based on
national regulations apply, if any.This document does not apply to boxes and enclosures for electrical accessories for
household and similar fixed electrical installations as defined in IEC 60670-24.---------------------- Page: 11 ----------------------
SIST EN IEC 61439-7:2021
– 6 – IEC 61439-7:2018 © IEC 2018
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.Clause 2 of IEC 61439-1:2011 is applicable except as follows.
Addition:
IEC 60068-2-27, Environmental testing – Part 2-27: Tests – Test Ea and guidance: Shock
IEC 60068-2-75, Environmental testing – Part 2-75: Tests – Test Eh: Hammer testsIEC 61439-1:2011, Low-voltage switchgear and controlgear assemblies – Part 1: General
rules3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 61439-1:2011 and
the following apply.ISO and IEC maintain terminological databases for use in standardization at the following
addresses:• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
Clause 3 of IEC 61439-1:2011 is applicable except as follows.
3.1 General terms
Additional terms:
3.1.701
low voltage switchgear and controlgear ASSEMBLY for marinas and harbors sites
AMHS
combination of one or more transforming or switching devices together with associated
control, measuring, signaling, protective and regulating equipment, with all their internal
electrical and mechanical interconnections and structural parts, designed and built for use in
all marinas, harbors and similar sitesNote 1 to entry: This note applies to the French language only.
3.1.702
low voltage switchgear and controlgear ASSEMBLY for camping and caravan sites
ACCS
combination of one or more transforming or switching devices together with associated
control, measuring, signaling, protective and regulating equipment, with all their internal
electrical and mechanical interconnections and structural parts, designed and built for use in
all camping, caravan and similar sitesNote 1 to entry: This note applies to the French language only.
---------------------- Page: 12 ----------------------
SIST EN IEC 61439-7:2021
IEC 61439-7:2018 © IEC 2018 – 7 –
3.1.703
low voltage switchgear and controlgear ASSEMBLY for markets and other outdoor public
sitesAMPS
combination of one or more transforming or switching devices together with associated
control, measuring, signaling, protective and regulating equipment, with all their internal
electrical and mechanical interconnections and structural parts, designed and built for use in
all market squares and other similar outdoor public sitesNote 1 to entry: This note applies to the French language only.
3.1.704
low voltage switchgear and controlgear ASSEMBLY for electric vehicles charging stations
AEVCScombination of one or more transforming or switching devices together with associated
control, measuring, signaling, protective and regulating equipment, with all their internal
electrical and mechanical interconnections and structural parts, designed and built for electric
vehicle charging stationsNote 1 to entry: This note applies to the French language only.
3.3 External design of ASSEMBLIES
Modification:
3.3.1
open-type ASSEMBLY
This term of IEC 61439-1:2011 does not apply.
3.3.2
dead-front ASSEMBLY
This term of IEC 61439-1:2011 does not apply.
3.5 Conditions of installation of ASSEMBLIES
3.5.3
stationary ASSEMBLY
Additional terms:
3.5.3.701
ground and floor mounted ASSEMBLY
stationary ASSEMBLY permanently connected to the supply with a part embedded in the ground
or intended to be fixed directly on the floor or a baseNote 1 to entry: This type of ASSEMBLY includes poles and columns.
3.5.3.702
wall mounted ASSEMBLY
stationary ASSEMBLY intended to be fixed directly on the wall while being permanently fixed to
the supply3.5.4
movable ASSEMBLY
This term of IEC 61439-1:2011 does not apply.
---------------------- Page: 13 ----------------------
SIST EN IEC 61439-7:2021
– 8 – IEC 61439-7:2018 © IEC 2018
Additional terms:
3.5.701
permanently connected ASSEMBLY
ASSEMBLY that can only be connected to, or disconnected from, the AC or DC supply network
by the use of a toolNote 1 to entry: This ASSEMBLY corresponds to the definition of permanently connected EV supply equipment
provided in IEC 61851-1:2017.3.5.702
transportable ASSEMBLY
ASSEMBLY intended for use in a place where it is not permanently fixed. When the equipment
is to be moved to another place, it is first disconnected from the supply network
3.5.703mobile ASSEMBLY
ASSEMBLY which is capable to be moved while in operation or which can easily be moved from
one place to another while connected to the supply network3.5.704
ASSEMBLY for locations with restricted access
ASSEMBLY accessible to all persons who are authorized to have access to the location (e.g.
equipment located in private housing, private parking areas or similar places)Note 1 to entry: This ASSEMBLY corresponds to the definition of "equipment" for locations with restricted access
provided in IEC 61851-1:2017.3.5.705
ASSEMBLY for locations with non-restricted access
ASSEMBLY accessible for all persons, e.g. the access is given in a public area
Note 1 to entry: This ASSEMBLY corresponds to the definition of "equipment" for locations with non-restricted
access provided in IEC 61851-1:2017.3.5.706
water and other fluids system
part of the ASSEMBLY which contains water tubes, valves, joins and taps as service to
connected userEXAMPLE 1 Possible other fluids are compressed air, natural gasses, drinkable water and wastewater.
3.5.707base
additional part of the arrangement used to support the ASSEMBLY in any case of mounting
intended to accommodate only cables3.5.708
fixing means
accessories intended to fix the base or the ASSEMBLY to the ground, to the floor or to the wall
etc.4 Symbols and abbreviations
Clause 4 of IEC 61439-1:2011 is applicable except as follows.
Addition:
---------------------- Page: 14 ----------------------
SIST EN IEC 61439-7:2021
IEC 61439-7:2018 © IEC 2018 – 9 –
Symbol/Abbreviation Term Subclause
AMHS low voltage switchgear and controlgear assembly for marinas and harbors sites 3.1.701
ACCS low voltage switchgear and controlgear assembly for camping and caravan sites 3.1.702
low voltage switchgear and controlgear assembly for markets and other outdoorAMPS 3.1.703
public sites
AEVCS low voltage switchgear and controlgear assembly for electric vehicles charging station 3.1.704
5 Interface characteristicsClause 5 of IEC 61439-1:2011 is applicable except as follows. Items subject to agreement
between the ASSEMBLY manufacturer and the user: see Annex AA.5.1 General
Replacement:
The characteristics of the ASSEMBLY shall ensure compatibility with the ratings of the circuits
to which it is connected and the installation conditions and shall be declared by the ASSEMBLY
manufacturer using the criteria identified in 5.2 to 5.6, 5.701 and 5.702.5.4 Rated diversity factor (RDF)
Addition:
In the absence of information concerning the actual load currents, the assumed loading of the
ASSEMBLY or group of outgoing circuits, the factor in Table 701 below,outgoing circuits of the
may be used.
Table 701 does not apply for AEVCS. For AEVCS the rated diversity factor of the outgoing
circuit supplying directly the connecting point shall be taken as equal to 1. The rated diversity
factor of the distribution circuit supplying multiple connecting points may be re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.