oSIST prEN 13238:2018
(Main)Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates
Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates
This European Standard describes the conditioning procedures for test specimens which will be tested according to the European standards for reaction to fire.
The rules for the selection of substrates for construction products when carrying out reaction to fire tests are also detailed in this European Standard.
This European Standard does not contain requirements for
- the pre-drying of test specimens for the non-combustibility test according EN ISO 1182;
- methods of cleaning (e.g. washing) and other methods for the assessment of durability aspects, which are dealt with in the relevant product standards.
Prüfungen zum Brandverhalten von Bauprodukten - Konditionierungsverfahren und allgemeine Regeln für die Auswahl von Trägerplatten
Dieses Dokument beschreibt die Verfahren zur Konditionierung von Probekörpern, die nach Europäischen Normen für das Brandverhalten geprüft werden.
Die Regeln für die Auswahl von Trägerplatten für Bauprodukte zur Durchführung von Prüfungen zum Brandverhalten werden ebenfalls in diesem Dokument behandelt.
Dieses Dokument enthält keine Anforderungen an
die Vortrocknung von Probekörpern für die Nichtbrennbarkeitsprüfung nach EN ISO 1182;
die Reinigungsverfahren (z. B. Waschen) und weitere Verfahren zur Beurteilung der Dauerhaftigkeit, da diese in den jeweiligen Produktnormen behandelt werden.
Essais de réaction au feu des produits de construction - Modes opératoires de conditionnement et règles générales de sélection des substrats
Le présent document décrit les modes opératoires de conditionnement des éprouvettes qui seront soumises aux essais de réaction au feu conformément aux Normes européennes.
Les règles de sélection des substrats pour les produits de construction pour les essais de réaction au feu sont également détaillées dans le présent document.
Le présent document ne spécifie pas d’exigences concernant :
- le pré-séchage des éprouvettes pour l’essai d’incombustibilité conformément à l’EN ISO 1182 ;
- les méthodes de nettoyage (par exemple, lavage) et autres méthodes d’évaluation des aspects de la durabilité qui sont traités dans les normes produits correspondantes.
Preskusi odziva gradbenih proizvodov na ogenj - Postopki kondicioniranja in splošna pravila za izbiro podlag
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 13238:2018
01-december-2018
Preskusi odziva gradbenih proizvodov na ogenj - Postopki kondicioniranja in
splošna pravila za izbiro podlag
Reaction to fire tests for building products - Conditioning procedures and general rules
for selection of substrates
Prüfungen zum Brandverhalten von Bauprodukten - Konditionierungsverfahren und
allgemeine Regeln für die Auswahl von Trägerplatten
Essais de réaction au feu des produits de construction - Modes opératoires de
conditionnement et règles générales de sélection des substrats
Ta slovenski standard je istoveten z: prEN 13238
ICS:
13.220.50 Požarna odpornost Fire-resistance of building
gradbenih materialov in materials and elements
elementov
oSIST prEN 13238:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13238:2018
---------------------- Page: 2 ----------------------
oSIST prEN 13238:2018
DRAFT
EUROPEAN STANDARD
prEN 13238
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2018
ICS 13.220.50 Will supersede EN 13238:2010
English Version
Reaction to fire tests for building products - Conditioning
procedures and general rules for selection of substrates
Essais de réaction au feu des produits de construction - Prüfungen zum Brandverhalten von Bauprodukten -
Modes opératoires de conditionnement et règles Konditionierungsverfahren und allgemeine Regeln für
générales de sélection des substrats die Auswahl von Trägerplatten
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 127.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13238:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13238:2018
prEN 13238:2018 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Conditioning procedures . 6
4.1 General . 6
4.2 Conditioning to constant mass . 7
4.3 Conditioning for a fixed period . 7
5 General rules for selection of substrates . 7
5.1 General . 7
5.2 Standard substrates for floorings . 7
5.3 Standard substrates for construction products excluding floorings . 8
Bibliography . 11
2
---------------------- Page: 4 ----------------------
oSIST prEN 13238:2018
prEN 13238:2018 (E)
European foreword
This document (prEN 13238:2018) has been prepared by Technical Committee CEN/TC 127 “Fire
safety in buildings”, the secretariat of which is held by BSI.
This document will supersedes EN 13238:2010.
This document has been prepared under a mandate given to CEN by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
3
---------------------- Page: 5 ----------------------
oSIST prEN 13238:2018
prEN 13238:2018 (E)
Introduction
The Construction Products Directive requires products to be tested in their end use condition which,
for the purpose of substrates, could lead to an economically unrealistic large variety of tests to be
carried out. This large spectrum has been reduced to a practical number of standard substrates that
enables the majority of end use conditions to be represented. Rules for the selection of such substrates
are given in this document.
This document is intended for use in conjunction with European Standards covering the reaction to
fire test methods for the relevant construction products.
4
---------------------- Page: 6 ----------------------
oSIST prEN 13238:2018
prEN 13238:2018 (E)
1 Scope
This document describes the conditioning procedures for test specimens which will be tested
according to the European standards for reaction to fire.
The rules for the selection of substrates for construction products when carrying out reaction to fire
tests are also detailed in this document.
This document does not contain requirements for
— the pre-drying of test specimens for the non-combustibility test according EN ISO 1182;
— methods of cleaning (e.g. washing) and other methods for the assessment of durability aspects,
which are dealt with in the relevant product standards.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
EN 312, Particleboards - Specifications
EN 13823, Reaction to fire tests for building products — Building products excluding floorings exposed to
the thermal attack by a single burning item
EN 14390, Fire test - Large-scale room reference test for surface products
EN 16733, Reaction to fire tests for building products - Determination of a building product's propensity
to undergo continuous smouldering
CEN/TS 1187, Test methods for external fire exposure to roofs
EN ISO 1182, Reaction to fire tests for products - Non-combustibility test (ISO 1182)
EN ISO 1716, Reaction to fire tests for products - Determination of the gross heat of combustion (calorific
value) (ISO 1716)
EN ISO 9239-1, Reaction to fire tests for floorings - Part 1: Determination of the burning behaviour using
a radiant heat source (ISO 9239-1)
EN ISO 11925-2, Reaction to fire tests - Ignitability of products subjected to direct impingement of flame -
Part 2: Single-flame source test (ISO 11925-2)
EN ISO 13943:2000, Fire safety — Vocabulary (ISO 13943:2000)
5
---------------------- Page: 7 ----------------------
oSIST prEN 13238:2018
prEN 13238:2018 (E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 13943:2000 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
material
single basic substance or uniformly dispersed mixture of substances, e.g. metal, stone, timber,
concrete, mineral wool with uniformly dispersed binder or polymers
3.2
product
material, element or component about which information is required
3.3
substrate
product which is used immediately beneath the product about which information is required
Note 1 to entry: For a flooring, it is the floor on which the flooring is mounted or the material which represents
this floor.
3.4
standard substrate
product which is representative of the substrate used in end use applications
3.5
test specimen
piece of the product which is to be tested together with or without any substrate or treatment
Note 1 to entry: The test specimen may include an air gap.
3.6
conditioning
exposure to a controlled atmosphere
4 Conditioning procedures
4.1 General
Test specimens used by the laboratory to conduct tests according to EN ISO 1182, EN ISO 1716,
EN ISO 9239-1, EN ISO 11925-2, EN 13823, EN 14390, EN 16733 and CEN/TS1187 shall be
conditioned a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.