SIST EN ISO 15792-1:2008/A1:2013
(Amendment)Welding consumables - Test methods - Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys (ISO 15792-1:2000/Amd 1:2011)
Welding consumables - Test methods - Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys (ISO 15792-1:2000/Amd 1:2011)
This part of ISO 15792 specifies the preparation of test piece and specimens. The purpose is to determine mechanical properties of all-weld metal where required by the consumable classification standard or for other purposes, in arc welding of steel, nickel and nickel alloys. This part of ISO 15792 is not applicable to single- or two-pass welding or fillet welding. For these cases, ISO 15792-2 and ISO 15792-3 apply.
Schweißzusätze - Prüfverfahren - Teil 1: Prüfverfahren für Prüfstücke zur Entnahme von Schweißgutproben an Stahl, Nickel und Nickellegierungen (ISO 15792-1:2000/Amd 1:2011)
Produits consommables pour le soudage - Méthodes d'essai - Partie 1: Méthodes d'essai pour les éprouvettes de métal fondu hors dilution pour le soudage de l'acier, du nickel et des alliages de nickel (ISO 15792-1:2000/Amd 1:2011)
Dodajni materiali za varjenje - Preskusne metode - 1. del: Preskusne metode za čisti var na jeklu, niklju in nikljevih zlitinah (ISO 15792-1:2000/Amd 1:2011)
Ta del standarda ISO 15792 opisuje pripravo preskušanca in vzorcev. Namen je določanje mehanske lastnosti čistega vara, kjer je to zahtevano s standardom za razvrščanje dodajnih materialov, ali za druge namene pri obločnem varjenju jekla, niklja in nikljevih zlitin. Ta del standarda ISO 15792 se ne uporablja za enopotezno, dvopotezno ali kotno varjenje. V teh primerih se uporabljata standarda ISO 15792-2 in ISO 15792-3.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15792-1:2008/A1:2013
01-december-2013
'RGDMQLPDWHULDOL]DYDUMHQMH3UHVNXVQHPHWRGHGHO 3UHVNXVQHPHWRGH]D
þLVWLYDUQDMHNOXQLNOMXLQQLNOMHYLK]OLWLQDK ,62 $PG
Welding consumables - Test methods - Part 1: Test methods for all-weld metal test
specimens in steel, nickel and nickel alloys (ISO 15792-1:2000/Amd 1:2011)
Schweißzusätze - Prüfverfahren - Teil 1: Prüfverfahren für Prüfstücke zur Entnahme von
Schweißgutproben an Stahl, Nickel und Nickellegierungen (ISO 15792-1:2000/Amd
1:2011)
Produits consommables pour le soudage - Méthodes d'essai - Partie 1: Méthodes d'essai
pour les éprouvettes de métal fondu hors dilution pour le soudage de l'acier, du nickel et
des alliages de nickel (ISO 15792-1:2000/Amd 1:2011)
Ta slovenski standard je istoveten z: EN ISO 15792-1:2008/A1:2011
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 15792-1:2008/A1:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15792-1:2008/A1:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 15792-1:2008/A1:2013
EUROPEAN STANDARD
EN ISO 15792-1:2008/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2011
ICS 25.160.20
English Version
Welding consumables - Test methods - Part 1: Test methods for
all-weld metal test specimens in steel, nickel and nickel alloys
(ISO 15792-1:2000/Amd 1:2011)
Produits consommables pour le soudage - Méthodes Schweißzusätze - Prüfverfahren - Teil 1: Prüfverfahren für
d'essai - Partie 1: Méthodes d'essai pour les éprouvettes Prüfstücke zur Entnahme von Schweißgutproben an Stahl,
de métal fondu hors dilution pour le soudage de l'acier, du Nickel und Nickellegierungen (ISO 15792-1:2000/Amd
nickel et des alliages de nickel (ISO 15792-1:2000/Amd 1:2011)
1:2011)
This amendment A1 modifies the European Standard EN ISO 15792-1:2008; it was approved by CEN on 30 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15792-1:2008/A1:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15792-1:2008/A1:2013
EN ISO 15792-1:2008/A1:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15792-1:2008/A1:2013
EN ISO 15792-1:2008/A1:2011 (E)
Foreword
This document (EN ISO 15792-1:2008/A1:2011) has been prepared by Technical Committee ISO/TC 44
"Welding and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the
latest by April 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
...
SLOVENSKI STANDARD
SIST EN ISO 15792-1:2008/oprA1:2010
01-december-2010
'RGDMQLPDWHULDOL]DYDUMHQMH3UHVNXVQHPHWRGHGHO 3UHVNXVQHPHWRGH]D
þLVWLYDUQDMHNOXQLNOMXLQQLNOMHYLK]OLWLQDK ,62 '$0
Welding consumables - Test methods - Part 1: Test methods for all-weld metal test
specimens in steel, nickel and nickel alloys (ISO 15792-1:2000/DAM 1:2010)
Schweißzusätze - Prüfverfahren - Teil 1: Prüfverfahren für Prüfstücke zur Entnahme von
Schweißgutproben an Stahl, Nickel und Nickellegierungen (ISO 15792-1:2000/DAM
1:2010)
Produits consommables pour le soudage - Méthodes d'essai - Partie 1: Méthodes d'essai
pour les éprouvettes de métal fondu hors dilution pour le soudage de l'acier, du nickel et
des alliages de nickel (ISO 15792-1:2000/DAM 1:2010)
Ta slovenski standard je istoveten z: EN ISO 15792-1:2008/prA1
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 15792-1:2008/oprA1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15792-1:2008/oprA1:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 15792-1:2008/oprA1:2010
EUROPEAN STANDARD
DRAFT
EN ISO 15792-1:2008
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
October 2010
ICS 25.160.20
English Version
Welding consumables - Test methods - Part 1: Test methods for
all-weld metal test specimens in steel, nickel and nickel alloys
(ISO 15792-1:2000/DAM 1:2010)
Produits consommables pour le soudage - Méthodes Schweißzusätze - Prüfverfahren - Teil 1: Prüfverfahren für
d'essai - Partie 1: Méthodes d'essai pour les éprouvettes Prüfstücke zur Entnahme von Schweißgutproben an Stahl,
de métal fondu hors dilution pour le soudage de l'acier, du Nickel und Nickellegierungen (ISO 15792-1:2000/DAM
nickel et des alliages de nickel (ISO 15792-1:2000/DAM 1:2010)
1:2010)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 121.
This draft amendment A1, if approved, will modify the European Standard EN ISO 15792-1:2008. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15792-1:2008/prA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15792-1:2008/oprA1:2010
EN ISO 15792-1:2008/prA1:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15792-1:2008/oprA1:2010
EN ISO 15792-1:2008/prA1:2010 (E)
Foreword
This document (EN ISO 15792-1:2008/prA1:2010) has been prepared by Technical Committee ISO/TC 44
"Welding and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the
secretariat of which is held by DIN.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 15792-1:2000/DAM 1:2010 has been approved by CEN as a EN ISO 15792-1:2008/prA1:2010
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15792-1:2008/oprA1:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 15792-1:2008/oprA1:2010
DRAFT AMENDMENT ISO 15792-1:2000/DAmd 1
ISO/TC 44/SC 3 Secretariat: ANSI
Voting begins on: Voting terminates on:
2010-10-07 2011-03-07
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Welding consumables — Test methods —
Part 1:
Test methods for all-weld metal test specimens in steel, nickel
and nickel alloys
AMENDMENT 1
Produits consommables pour le soudage — Méthodes d'essai —
Partie 1: Méthodes d'essai pour les éprouvettes de métal fondu hors dilution pour le soudage de l'acier, du
nickel et des alliages de nickel
AMENDEMENT 1
ICS 25.160.20
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.