SIST EN ISO 4894-2:2000
(Main)Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 4894-2:1995)
Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 4894-2:1995)
Cancels and replaces the first edition (1981). Specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of SAN moulding and extrusion materials. Gives requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing. Gives procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made. Lists properties and test methods which are suitable and necessary to characterize SAN moulding and extrusion materials.
Kunststoffe - Styrol/Acrylnitril (SAN)-Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 4894-2:1995)
Dieser Teil von ISO 4894 legt die Bedingungen zur Herstellung von Probeko(rpern und die zur Bestimmung der Eigenschaften von SAN-Formmassen anzuwendenden Pru(fverfahren fest. Anforderungen an die Behandlung des Probenmaterials und fu(r das Konditionieren des Probenmaterials vor der Herstellung der Probeko(rper und der Probeko(rper vor der Pru(fung sind ebenfalls enthalten. Verfahren und Bedingungen fu(r die Herstellung der Probeko(rper und Vorschriften fu(r die Bestimmung der Eigenschaften der Formmasse, aus der die Probeko(rper hergestellt werden, sind angegeben.
Plastiques - Styrene/acrylonitrile (SAN) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 4894-2:1995)
La présente partie de l'ISO 4894 prescrit les méthodes de préparation des éprouvettes et les méthodes d'essai à appliquer pour déterminer les propriétés des SAN pour moulage et extrusion. Elle indique les exigences requises lors de la manipulation du matériau pour essai, ainsi que lors du conditionnement dudit matériau avant moulage et des éprouvettes avant l'essai. Elle précise les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesurage des propriétés des matériaux à partir desquels ces éprouvettes sont fabriquées. Elle fournit également une liste des propriétés et des méthodes d'essai appropriées et nécessaires à la caractérisation des SAN pour moulage et extrusion. Les propriétés ont été choisies à partir des méthodes d'essai générales données dans l'ISO 10350. D'autres méthodes d'essai, présentant une importance particulière ou largement utilisées dans le cas de ces matériaux pour moulage et extrusion, sont également incluses dans la présente partie de l'ISO 4894, de même qu'elles figurent dans les propriétés de désignation de l'ISO 4894-1.
Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz kopolimerov stiren/akrilonitril (SAN) - 2. del: Priprava preskušancev in določanje lastnosti (ISO 4894-2:1995)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 4894-2:2000
01-maj-2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]NRSROLPHURY
VWLUHQDNULORQLWULO 6$1 GHO 3ULSUDYDSUHVNXãDQFHYLQGRORþDQMHODVWQRVWL ,62
Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties (ISO 4894-2:1995)
Kunststoffe - Styrol/Acrylnitril (SAN)-Formmassen - Teil 2: Herstellung von Probekörpern
und Bestimmung von Eigenschaften (ISO 4894-2:1995)
Plastiques - Styrene/acrylonitrile (SAN) pour moulage et extrusion - Partie 2: Préparation
des éprouvettes et détermination des propriétés (ISO 4894-2:1995)
Ta slovenski standard je istoveten z: EN ISO 4894-2:1999
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 4894-2:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 4894-2:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 4894-2:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 4894-2:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 4894-2:2000
---------------------- Page: 5 ----------------------
SIST EN ISO 4894-2:2000
---------------------- Page: 6 ----------------------
SIST EN ISO 4894-2:2000
INTERNATIONAL
IS0
STANDARD
4894-2
Second edition
1995-05-01
Plastics - Styrene/acrylonitrile (SAN)
moulding and extrusion materials -
Part 2:
Preparation of test specimens and
determination of properties
P/as tiques - Styr&ne/acryionitrile (SAN) pour moulage et extrusion -
Partie 2: Prbpara tion des kprouve ttes et dhermina tion des propriMs
Reference number
IS0 4894-Z: 1995(E)
---------------------- Page: 7 ----------------------
SIST EN ISO 4894-2:2000
IS0 4894-2: 1995(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(I EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 4894-2 was prepared by Technical Committee
lSO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.
This second edition cancels and replaces the first edition
an includes the following changes:
(IS0 4894-2:1981) d
The text has been brought into accordance with the frame text developed
by SC 9. The table of test methods has been revised in accordance with
IS0 10350.
IS0 4894 consists of the following parts, under the general title
P/as tics - Styrene/acrylonitrile (SAN) moulding and extrusion materials:
- Part 1: Designation
- Part 2: Preparation of test specimens and determination of proper-
ties
Annex A forms an integral part of this part of IS0 4894.
0 IS0 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii
---------------------- Page: 8 ----------------------
SIST EN ISO 4894-2:2000
INTERNATIONAL STANDARD 0 IS0 IS0 4894-2: 1995(E)
Plastics - Styrene/acrylonitrile (SAN) moulding and
extrusion materials -
Part 2:
Preparation of test specimens and determination of
properties
2 Normative references
1 Scope
The following standards contain provisions which,
through reference in this text, constitute provisions
of this part of IS0 4894. At the time of publication, the
This part of IS0 4894 specifies the methods of prep-
editions indicated were valid. All standards are subject
aration of test specimens and the test methods to be
to revision, and parties to agreements based on this
used in determining the properties of SAN moulding
part of IS0 4894 are encouraged to investigate the
and extrusion materials. Requirements for handling
possibility of applying the most recent editions of the
test material and for conditioning both the test ma-
standards indicated below. Members of IEC and IS0
terial before moulding and the specimens before
maintain registers of currently valid International
testing are given here.
Standards.
Procedures and conditions for the preparation of test
Determination of water ab-
IS0 62:1980, Plastics -
specimens and procedures for measuring properties
sorption.
of the materials from which these specimens are
made are given. Properties and test methods which
IS0 75-l : 1993, Plastics - Determination of tempera-
are suitable and necessary to characterize SAN
ture of deflection under load - Part I: General test
moulding and extrusion materials are listed.
method.
The properties have been selected from the general
IS0 75-2: 1993, Plastics - Determination of tempera-
test methods in IS0 10350. Other test methods in
ture of deflection under load - Part 2: Plastics and
wide use for or of particular significance to these
ebonite.
moulding and extrusion materials are also included in
this part of IS0 4894, as are the designatory proper-
IS0 178:1993, Plastics - Determination of flexural
ties specified in part 1: Vicat softening temperature,
properties.
melt flow rate, impact strength and flexural modulus.
IS0 179:1993, Plastics - Determination of Charpy
In order to obtain reproducible and comparable test
impact strength.
results, it is necessary to use the methods of speci-
men preparation and conditioning, the specimen di- IS0 291 :I 977, Plastics
- Standard atmospheres for
mensions and the test procedures specified herein. conditioning and testing.
Values determined will not necessarily be identical to
those obtained using specimens of different dimen- IS0 293: 1986, Plastics - Compression moulding test
sions or prepared using different procedures. specimens of thermoplastic materials.
---------------------- Page: 9 ----------------------
SIST EN ISO 4894-2:2000
(0 IS0
IS0 4894-2: 1995(E)
IS0 294: 1995, Plastics - Injection moulding of test IS0 4589-3: --‘I, P/as tics - Determination of burning
specimens of thermoplastic materials. behaviour by oxygen index - Part 3: Elevated-
temperature test.
IS0 306:1994, Plastics - Thermoplastic materials -
IS0 4894-l : 1990, Plastics - Styrene/acrylonitrile
Determination of Vicat softening temperature (VST).
(SAiV) copolymer moulding and extrusion materials
IS0 527-l :I 993, Plastics - Determination of tensile - Part 7: Designation.
properties - Part 7: General principles.
IS0 8256:1990, Plastics - Determination of tensile-
IS0 527-2:1993, Plastics - Determination of tensile impact strength.
properties - Part 2: Test conditions for moulding and
extrusion p/as tics. IS0 10350: 1993, Plastics - Acquisition and presen-
ta tion of comparable single-point data.
IS0 527-4:-l), Plastics - Determination of tensile
properties - Part 4: Test conditions for isotropic and IEC 93:1980, Methods of test for volume resistivity
orthotropic fibre-rein forced p/as tic composites. and surface resistivity of solid electrical insulating
materials.
IS0 899-l : 1993, Plastics - Determination of creep
IEC 112:1979, Method for determining the compar-
behaviour - Part 7: Tensile creep.
ative and the proof tracking indices of solid insulating
IS0 1133:1991, Plastics - Determination of the melt
materials under moist conditions.
mass-flow rate (MFt?) and the melt volume-flow rate
(M VR) of thermoplastics. IEC 243-l :I 988, Methods of test for electric strength
of solid insulating materials - Part 7: Tests at power
IS0 1183:1987, Plastics - Methods for determining
frequencies.
the density and relative density of non-cellular
IEC 250: 1969, Recommended methods for the deter-
plastics.
mination of the permittivity and dielectric dissipation
IS0 1210:1992, Plastics - Determination of the factor of electrical insulating materials at power, audio
burning behaviour of horizontal and vertical specimens and radio frequencies including metre wavelengths.
in contact with a small-flame ignition source.
IEC 296: 1982, Specification for unused mineral insu-
IS0 1656:1988, Rubber
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.