Cranes - Monitoring for crane design working period

This International Standard specifies a method for monitoring, during long-term operation, the actual
duty of the crane, and a means of comparing this to the original design duty which was specified through
classification. The related design standard is ISO 4301-1. Approaching the design life limit means an
increased probability of hazards. Monitoring of crane use — as described herein — provides a tool for
predicting the approach of the design limits and for focusing special inspections on the critical areas of
a crane.
This International Standard is intended to be used for adjusting/modifying the inspections defined in
ISO 9927-1.
It is applicable to cranes with a permanent construction throughout the life of the crane.
It is not applicable to mobile or tower cranes, except permanently installed tower cranes.
NOTE The method specified in this International Standard can be adapted to standards or rules other than
ISO 4301-1 which specify classifications.

Appareils de levage à charge suspendue - Surveillance continue de la période d'activité de conception

ISO 12482:2014 sp�cifie une m�thode pour la surveillance continue de l'exploitation r�elle de l'appareil de levage � charge suspendue, pendant un service prolong�, et sp�cifie les moyens de comparer cette exploitation r�elle au service de conception d'origine qui �tait sp�cifi� par le biais de la classification. La norme de conception correspondante est l'ISO 4301‑1. L'approche de la fin de la dur�e de vie th�orique repr�sente une augmentation de la probabilit� d'apparition de ph�nom�nes dangereux. La surveillance continue de l'exploitation des appareils de levage, tel que d�fini dans le pr�sent document, fournit un outil pour pr�dire l'approche des limites de conception et pour concentrer les inspections sp�ciales sur les zones critiques d'un appareil de levage.
La pr�sente Norme internationale est destin�e � �tre utilis�e pour adapter/modifier les inspections d�finies dans l'ISO 9927‑1.
Elle est applicable aux appareils de levage � construction permanente tout au long de leur dur�e de vie.
Elle ne s'applique ni aux grues mobiles, ni aux grues � tour, sauf les grues � tour mont�es de fa�on permanente.
NOTE La m�thode sp�cifi�e dans la pr�sente Norme internationale peut �tre adapt�e aux normes ou r�gles autres que la norme ISO 4301‑1 qui sp�cifient des classifications.

Žerjavi - Spremljanje projektiranega delovnega obdobja žerjava

Ta mednarodni standard določa metodo za spremljanje dejanske obremenitve žerjava med dolgoročnim delovanjem in način za primerjavo s prvotno konstrukcijsko obremenitvijo, ki je bila določena na podlagi
klasifikacije. S tem povezan standard za projektiranje je ISO 4301-1. Približevanje omejitvi življenjske dobe pomeni večjo verjetnost nastanka nevarnosti. Spremljanje uporabe žerjava – kot je opisano v tem standardu – zagotavlja orodje za napovedovanje približevanja konstrukcijskim omejitvam in za usmerjanje posebnih pregledov na ključna področja, povezana z
žerjavom.
Ta mednarodni standard naj bi se uporabljal za prilagajanje/spreminjanje pregledov iz standarda ISO 9927-1. Velja za žerjave s trajno konstrukcijo v celotni življenjski dobi žerjava. Ne velja za mobilne ali stolpne žerjave, razen za trajno nameščene stolpne žerjave.
OPOMBA Metodo iz tega mednarodnega standarda je mogoče prilagoditi standardom ali pravilom, ki niso določeni v standardu ISO 4301-1 in določajo razvrstitve.

General Information

Status
Published
Publication Date
16-Feb-2015
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Jan-2015
Due Date
28-Mar-2015
Completion Date
17-Feb-2015

Relations

Buy Standard

Standard
ISO 12482:2014 - Cranes -- Monitoring for crane design working period
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 12482:2015
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 12482:2014 - Appareils de levage a charge suspendue -- Surveillance continue de la durée de service par période d'activité de conception
French language
14 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 12482
First edition
2014-09-01
Cranes — Monitoring for crane design
working period
Appareils de levage à charge suspendue — Surveillance continue de la
période d’activité de conception
Reference number
ISO 12482:2014(E)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 12482:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 12482:2014(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Recording crane operation . 2
4.1 General . 2
4.2 Methods for counting duty . 2
4.3 Safety factor for duty counting . 3
5 Assessment of design working period . 3
5.1 General . 3
5.2 Schedule . 3
5.3 DWP calculation method . 3
6 Special assessment . 4
6.1 General . 4
6.2 Criteria for special assessment . 4
6.3 Responsibilities of crane user/owner . 4
6.4 Manufacturer’s instructions . 5
6.5 Report . 5
7 General overhaul (GO) . 5
7.1 General . 5
7.2 Categories of actions . 5
Annex A (normative) DWP calculation for cranes designed to ISO 4301‑1 .7
Annex B (normative) DWP calculation for hoisting mechanisms designed to ISO 4301‑1 .10
Bibliography .13
© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 12482:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 96, Cranes, SC 5, Use, operation and maintenance.
ISO 12482 cancels and replaces ISO 12482-1:1995, which has been technically revised.
iv © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 12482:2014(E)

Introduction
Cranes are designed for a finite lifetime duty, which is specified in load cycles and load spectrum and is
not principally related to calendar working time. Classification of crane duty provides the crane owner
a means to specify the intended duty in order to achieve the intended useful operational lifetime of the
crane.
Typically the operational period for industrial cranes is from 10 to 20 years. However, a specified crane
classification may be related to any calendar time depending on the application, e.g. 5 to 10 years for a
special limited use or 40 years for a long-term investment.
Monitoring of crane use does not in any way change requirements for periodic inspections of the cranes,
independent of whatever type of instruments are used for the monitoring. Neither does it remove the
requirement for regular maintenance of cranes. Inspections and monitoring of use are methods, which
complete each other, giving different information of the condition.
The design working period (DWP) introduced in this standard is derived from the design classification
of cranes and is not to be considered as a guaranteed operational period in any respect. Due to the
probabilistic nature of metal fatigue and other influencing factors, premature failures during the DWP
cannot be ruled out. However, the DWP represents a reliable estimate of a safe operational period of the
crane, with due consideration to specified design regulations and standardized design safety factors.
© ISO 2014 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 12482:2014(E)
Cranes — Monitoring for crane design working period
1 Scope
This International Standard specifies a method for monitoring, during long-term operation, the actual
duty of the crane, and a means of comparing this to the original design duty which was specified through
classification. The related design standard is ISO 4301-1. Approaching the design life limit means an
increased probability of hazards. Monitoring of crane use — as described herein — provides a tool for
predicting the approach of the design limits and for focusing special inspections on the critical areas of
a crane.
This International Standard is intended to be used for adjusting/modifying the inspections defined in
ISO 9927-1.
It is applicable to cranes with a permanent construction throughout the life of the crane.
It is not applicable to mobile or tower cranes, except permanently installed tower cranes.
NOTE The method specified in this International Standard can be adapted to standards or rules other than
ISO 4301-1 which specify classifications.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 4301-1:1986, Cranes and lifting appliances — Classification — Part 1: General
ISO 4306-1, Cranes — Vocabulary — Part 1: General
ISO 9927-1, Cranes — Inspections — Part 1: General
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4301-1, ISO 4306-1 and the
following apply.
3.1
design duty
production capacity of a crane or hoist during its total useful operational period, specified by the original
design classification
3.2
design life
estimation of the allowable period of use for a crane based on its original design specifications and
taking into consideration the load cycles and load spectra expected during its intended usage
3.3
design working period
DWP
operation period in a specific actual duty, within which the design duty is reached
© ISO 2014 – All rights reserved 1

---------------------- Page: 6 ----------------------
ISO 12482:2014(E)

3.4
special assessment
SA
thorough examination and evaluation of the crane or hoist, to be made when the actual crane or hoist
duty approaches the design duty
3.5
general overhaul
GO
all refurbishment and maintenance actions based upon a special assessment (SA), required to extend
the safe operation life of a crane
3.6
work cycle
operating sequence starting from hoisting a load, transferring the load, lowering and grounding the
load, detaching the load and moving the unloaded load lifting attachment back to a starting position
ready to hoist another load
4 Recording crane operation
4.1 General
The crane owner should keep records of the crane use, adequate to identify the criteria specified by the
crane manufacturer and applicable to carry out the assessments described in this standard. Records
should also be kept of maintenance, inspections, repairs, modifications and exceptional occurrences,
e.g. overloads, extreme climatic conditions and collisions. Records should be updated at least once a year
during periodic inspections, see ISO 9927-1.
4.2 Methods for counting duty
Estimation of the duty history can be divided into the following categories, based on systematic and
reliable data collection and documentation procedures.
a) Crane operation data are recorded by a special, purpose-built system, which always operates
automatically when the crane is in use. The crane operator does not have a possibility to switch off
the recording system.
b) The crane is provided with counters recording the crane operation data. The user collects and
documents the operation data manually from the counters.
c) The crane duty history is calculated based upon a regular process in which the crane is working.
The crane is an integral part of the process. Process data are documented.
d) The crane duty history is estimated based upon a general production data of the site where the
crane is working.
e) The crane duty history is incomplete.
f) The crane duty history is unknown (e.g. in the case of a second-hand crane). The duty for DWP
calculation is based on estimate or assumed to be according to design classification and design life
reduced using the factor f from Table 1, item 5.
1
The basic Information for counting the crane use is in all cases provided by the crane owner/user.
Where recording instruments or counters are installed, the user should regularly inspect the instruments
to ensure that they are properly functioning.
2 © ISO 2014 – All rights reserved

---------------------- Page: 7 ----------------------
ISO 12482:2014(E)

4.3 Safety factor for duty counting
When calculating the design working period (DWP) of a crane, the estimated duty from the history shall
be increased by a safety factor, f , according to Table 1, to cover the unreliability in the duty recording
1
and estimation.
Table 1 — Safety factor f for duty counting
1
No. Method of duty recording f
1
1 Automatic recording system, 4.2 a), or 1,0
Counters and manual documentation, 4.2 b)
2 Estimation based upon a special, documented process, 4.2 c) 1,1
3 Estimation based upon documented production of the crane site, 4.2 d) 1,2
4 Estimation based upon undocumented, estimated production of the crane site, 4.2 e) 1,3
5 Crane duty history is unknown, 4.2 f) 1,5
5 Assessment of design working period
5.1 General
Many components of a crane may fail because of metal fatigue, which is difficult to predict or estimate
by physical inspections. Safeguarding against fatigue failure by physical inspections may be difficult
due to the following:
— the safe time window for an inspection from detectable to critical crack size can be short, leading to
unnecessary frequent inspections;
— detecting a fatigue crack would require in many cases a full disassembly of a component;
— planning and scheduling future repairs of the crane is not possible, and non-acceptance by an
inspection typically requires immediate action and possibly interruption of crane operation.
The purpose of the assessment of DWP is to estimate accumulated duty of the crane and assess its
remaining life.
It is assumed that
— all periodic inspections scheduled for the crane have been carried out,
— any damage suffered during the operation is recorded and appropriately repaired, and
— maintenance work, as well as replacement of worn parts, is carried out in accordance with the
manufacturer’s instructions.
5.2 Schedule
Collecting the data on the use of a crane and the assessment of DWP should be carried out in conjunction
with periodic inspections (see ISO 9927-1) at 12 month intervals.
5.3 DWP calculation method
The applied DWP calculation method should follow the specific
...

SLOVENSKI STANDARD
SIST ISO 12482:2015
01-marec-2015
1DGRPHãþD
SIST ISO 12482-1:1997
Žerjavi - Spremljanje projektiranega delovnega obdobja žerjava
Cranes - Monitoring for crane design working period
Appareils de levage à charge suspendue - Surveillance continue de la période d'activité
de conception
Ta slovenski standard je istoveten z: ISO 12482:2014
ICS:
53.020.20 Dvigala Cranes
SIST ISO 12482:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 12482:2015

---------------------- Page: 2 ----------------------

SIST ISO 12482:2015
INTERNATIONAL ISO
STANDARD 12482
First edition
2014-09-01
Cranes — Monitoring for crane design
working period
Appareils de levage à charge suspendue — Surveillance continue de la
période d’activité de conception
Reference number
ISO 12482:2014(E)
©
ISO 2014

---------------------- Page: 3 ----------------------

SIST ISO 12482:2015
ISO 12482:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 12482:2015
ISO 12482:2014(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Recording crane operation . 2
4.1 General . 2
4.2 Methods for counting duty . 2
4.3 Safety factor for duty counting . 3
5 Assessment of design working period . 3
5.1 General . 3
5.2 Schedule . 3
5.3 DWP calculation method . 3
6 Special assessment . 4
6.1 General . 4
6.2 Criteria for special assessment . 4
6.3 Responsibilities of crane user/owner . 4
6.4 Manufacturer’s instructions . 5
6.5 Report . 5
7 General overhaul (GO) . 5
7.1 General . 5
7.2 Categories of actions . 5
Annex A (normative) DWP calculation for cranes designed to ISO 4301‑1 .7
Annex B (normative) DWP calculation for hoisting mechanisms designed to ISO 4301‑1 .10
Bibliography .13
© ISO 2014 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 12482:2015
ISO 12482:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 96, Cranes, SC 5, Use, operation and maintenance.
ISO 12482 cancels and replaces ISO 12482-1:1995, which has been technically revised.
iv © ISO 2014 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 12482:2015
ISO 12482:2014(E)

Introduction
Cranes are designed for a finite lifetime duty, which is specified in load cycles and load spectrum and is
not principally related to calendar working time. Classification of crane duty provides the crane owner
a means to specify the intended duty in order to achieve the intended useful operational lifetime of the
crane.
Typically the operational period for industrial cranes is from 10 to 20 years. However, a specified crane
classification may be related to any calendar time depending on the application, e.g. 5 to 10 years for a
special limited use or 40 years for a long-term investment.
Monitoring of crane use does not in any way change requirements for periodic inspections of the cranes,
independent of whatever type of instruments are used for the monitoring. Neither does it remove the
requirement for regular maintenance of cranes. Inspections and monitoring of use are methods, which
complete each other, giving different information of the condition.
The design working period (DWP) introduced in this standard is derived from the design classification
of cranes and is not to be considered as a guaranteed operational period in any respect. Due to the
probabilistic nature of metal fatigue and other influencing factors, premature failures during the DWP
cannot be ruled out. However, the DWP represents a reliable estimate of a safe operational period of the
crane, with due consideration to specified design regulations and standardized design safety factors.
© ISO 2014 – All rights reserved v

---------------------- Page: 7 ----------------------

SIST ISO 12482:2015

---------------------- Page: 8 ----------------------

SIST ISO 12482:2015
INTERNATIONAL STANDARD ISO 12482:2014(E)
Cranes — Monitoring for crane design working period
1 Scope
This International Standard specifies a method for monitoring, during long-term operation, the actual
duty of the crane, and a means of comparing this to the original design duty which was specified through
classification. The related design standard is ISO 4301-1. Approaching the design life limit means an
increased probability of hazards. Monitoring of crane use — as described herein — provides a tool for
predicting the approach of the design limits and for focusing special inspections on the critical areas of
a crane.
This International Standard is intended to be used for adjusting/modifying the inspections defined in
ISO 9927-1.
It is applicable to cranes with a permanent construction throughout the life of the crane.
It is not applicable to mobile or tower cranes, except permanently installed tower cranes.
NOTE The method specified in this International Standard can be adapted to standards or rules other than
ISO 4301-1 which specify classifications.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 4301-1:1986, Cranes and lifting appliances — Classification — Part 1: General
ISO 4306-1, Cranes — Vocabulary — Part 1: General
ISO 9927-1, Cranes — Inspections — Part 1: General
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4301-1, ISO 4306-1 and the
following apply.
3.1
design duty
production capacity of a crane or hoist during its total useful operational period, specified by the original
design classification
3.2
design life
estimation of the allowable period of use for a crane based on its original design specifications and
taking into consideration the load cycles and load spectra expected during its intended usage
3.3
design working period
DWP
operation period in a specific actual duty, within which the design duty is reached
© ISO 2014 – All rights reserved 1

---------------------- Page: 9 ----------------------

SIST ISO 12482:2015
ISO 12482:2014(E)

3.4
special assessment
SA
thorough examination and evaluation of the crane or hoist, to be made when the actual crane or hoist
duty approaches the design duty
3.5
general overhaul
GO
all refurbishment and maintenance actions based upon a special assessment (SA), required to extend
the safe operation life of a crane
3.6
work cycle
operating sequence starting from hoisting a load, transferring the load, lowering and grounding the
load, detaching the load and moving the unloaded load lifting attachment back to a starting position
ready to hoist another load
4 Recording crane operation
4.1 General
The crane owner should keep records of the crane use, adequate to identify the criteria specified by the
crane manufacturer and applicable to carry out the assessments described in this standard. Records
should also be kept of maintenance, inspections, repairs, modifications and exceptional occurrences,
e.g. overloads, extreme climatic conditions and collisions. Records should be updated at least once a year
during periodic inspections, see ISO 9927-1.
4.2 Methods for counting duty
Estimation of the duty history can be divided into the following categories, based on systematic and
reliable data collection and documentation procedures.
a) Crane operation data are recorded by a special, purpose-built system, which always operates
automatically when the crane is in use. The crane operator does not have a possibility to switch off
the recording system.
b) The crane is provided with counters recording the crane operation data. The user collects and
documents the operation data manually from the counters.
c) The crane duty history is calculated based upon a regular process in which the crane is working.
The crane is an integral part of the process. Process data are documented.
d) The crane duty history is estimated based upon a general production data of the site where the
crane is working.
e) The crane duty history is incomplete.
f) The crane duty history is unknown (e.g. in the case of a second-hand crane). The duty for DWP
calculation is based on estimate or assumed to be according to design classification and design life
reduced using the factor f from Table 1, item 5.
1
The basic Information for counting the crane use is in all cases provided by the crane owner/user.
Where recording instruments or counters are installed, the user should regularly inspect the instruments
to ensure that they are properly functioning.
2 © ISO 2014 – All rights reserved

---------------------- Page: 10 ----------------------

SIST ISO 12482:2015
ISO 12482:2014(E)

4.3 Safety factor for duty counting
When calculating the design working period (DWP) of a crane, the estimated duty from the history shall
be increased by a safety factor, f , according to Table 1, to cover the unreliability in the duty recording
1
and estimation.
Table 1 — Safety factor f for duty counting
1
No. Method of duty recording f
1
1 Automatic recording system, 4.2 a), or 1,0
Counters and manual documentation, 4.2 b)
2 Estimation based upon a special, documented process, 4.2 c) 1,1
3 Estimation based upon documented production of the crane site, 4.2 d) 1,2
4 Estimation based upon undocumented, estimated production of the crane site, 4.2 e) 1,3
5 Crane duty history is unknown, 4.2 f) 1,5
5 Assessment of design working period
5.1 General
Many components of a crane may fail because of metal fatigue, which is difficult to predict or estimate
by physical inspections. Safeguarding against fatigue failure by physical inspections may be difficult
due to the following:
— the safe time window for an inspection from detectable to critical crack size can be short, leading to
unnecessary frequent inspections;
— detecting a fatigue crack would require in many cases a full disassembly of a component;
— planning and scheduling future repairs of the crane is not possible, and non-acceptance by an
inspection typically requires immediate action and possibly interruption of crane operation.
The purpose of the assessment of DWP is to estimate accumulated duty of the crane and assess its
remaining life.
It is assumed that
— all periodic inspections scheduled for the crane have been carried out,
— any damage suffered during the operation is recorded and appropri
...

NORME ISO
INTERNATIONALE 12482
Première édition
2014-09-01
Appareils de levage à charge
suspendue — Surveillance continue
de la durée de service par période
d’activité de conception
Cranes — Monitoring for crane design working period
Numéro de référence
ISO 12482:2014(F)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 12482:2014(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2014
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Version française parue en 2015
Publié en Suisse
ii © ISO 2014 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 12482:2014(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Enregistrement des opérations de l’appareil de levage . 2
4.1 Généralités . 2
4.2 Méthode de comptage du service . 2
4.3 Facteur de sécurité pour le comptage du service . 3
5 Évaluation de la période d’activité de conception (DWP) . 3
5.1 Généralités . 3
5.2 Calendrier . 4
5.3 Méthode de calcul de la période d’activité de conception DWP . 4
6 Évaluation spéciale (SA) . 4
6.1 Généralités . 4
6.2 Critères pour l’évaluation spéciale . 4
6.3 Responsabilités de l’utilisateur/du propriétaire de l’appareil de levage . 5
6.4 Instructions du fabricant . 5
6.5 Rapport . 5
7 Révision générale (GO) . 6
7.1 Généralités . 6
7.2 Catégories d’actions . 6
Annexe A (normative) Calcul de la DWP pour des appareils de levage conçus selon l’ISO 4301-1 .8
Annexe B (normative) Calcul de la DWP pour des mécanismes de levage conçus selon l’ISO 4301-1 .
11
Bibliographie .14
© ISO 2014 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 12482:2014(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui concerne
la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les
références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l’élaboration
du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de brevets reçues par
l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à l’évaluation de
la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes de l’OMC concernant
les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos — Informations
supplémentaires.
L’ISO 12482 a été élaborée par le comité technique ISO/TC 96, Appareils de levage à charge suspendue,
sous-comité SC 5, Utilisation, fonctionnement et entretien.
Cette deuxième édition annule et remplace la première édition (ISO 12482-1:1995) qui fait l’objet d’une
révision technique.
iv © ISO 2014 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 12482:2014(F)

Introduction
Les appareils de levage à charge suspendue sont conçus pour une durée de service finie, qui est
spécifiée en termes de cycles de charge et de spectre de charge et surtout qui n’est pas liée à un temps
d’utilisation calendaire. La classification du service de l’appareil de levage à charge suspendue fournit
au propriétaire de l’appareil un moyen de spécifier le service prévu afin d’atteindre la durée de vie utile
de fonctionnement prévue de l’appareil de levage à charge suspendue.
La durée d’exploitation des appareils de levage industriels varie typiquement de 10 à 20 ans. Toutefois,
une classification spécifiée d’appareil de levage peut être liée à toute durée calendaire dépendant d’une
application, par exemple 5 à 10 ans pour une utilisation spéciale limitée ou 40 ans pour un investissement
à long terme.
L’utilisation de la surveillance continue de l’appareil de levage ne modifie en aucun cas les exigences
d’inspections périodiques des appareils de levage, quels que soient les types d’instruments utilisés pour
cette surveillance continue. Il n’annule pas non plus l’exigence d’entretien régulier des appareils de
levage. Les inspections et la surveillance continue de l’exploitation sont des méthodes qui se complètent
l’une et l’autre et donnent des informations différentes sur l’état de l’appareil de levage.
La période d’activité de conception (DWP) introduite dans la présente norme est dérivée de la
classification de conception des appareils de levage à charge suspendue et ne doit en aucun cas être
considérée comme une période opérationnelle garantie. Il n’est pas possible d’exclure des défaillances
prématurées au cours de la période d’activité de conception, en raison de la nature probabiliste de la
fatigue du métal et du fait d’autres facteurs d’influence. Toutefois, la période d’activité de conception
(DWP) constitue une estimation fiable d’une période opérationnelle sure, tenant compte des règles de
conception spécifiées et de facteurs de sécurité de calcul normalisés.
© ISO 2014 – Tous droits réservés v

---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 12482:2014(F)
Appareils de levage à charge suspendue — Surveillance
continue de la durée de service par période d’activité de
conception
1 Domaine d’application
La présente Norme internationale spécifie une méthode pour la surveillance continue de l’exploitation
réelle de l’appareil de levage à charge suspendue, pendant un service prolongé, et spécifie les moyens de
comparer cette exploitation réelle au service de conception d’origine qui était spécifié par le biais de la
classification. La norme de conception correspondante est l’ISO 4301-1. L’approche de la fin de la durée de
vie théorique représente une augmentation de la probabilité d’apparition de phénomènes dangereux. La
surveillance continue de l’exploitation des appareils de levage, tel que défini dans le présent document,
fournit un outil pour prédire l’approche des limites de conception et pour concentrer les inspections
spéciales sur les zones critiques d’un appareil de levage.
La présente Norme internationale est destinée à être utilisée pour adapter/modifier les inspections
définies dans l’ISO 9927-1.
Elle est applicable aux appareils de levage à construction permanente tout au long de leur durée de vie.
Elle ne s’applique ni aux grues mobiles, ni aux grues à tour, sauf les grues à tour montées de façon
permanente.
NOTE La méthode spécifiée dans la présente Norme internationale peut être adaptée aux normes ou règles
autres que la norme ISO 4301-1 qui spécifient des classifications.
2 Références normatives
Les documents suivants, en totalité ou en partie, sont référencés de manière normative dans le présent
document et sont indispensables pour son application. Pour les références datées, seule l’édition citée
s’applique. Pour les références non datées, la dernière édition du document de référence s’applique (y
compris les éventuels amendements).
ISO 4301-1:1986, Grues et appareils de levage — Classification — Partie 1: Généralités
ISO 4306-1, Appareils de levage à charge suspendue — Vocabulaire — Partie 1: Généralités
ISO 9927-1, Appareils de levage à charge suspendue — Vérifications — Partie 1: Généralités
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l’ISO 4301-1, l’ISO 4306-1
ainsi que les suivants s’appliquent.
3.1
service de conception
capacité de production d’un appareil de levage ou d’un palan sur toute sa durée d’exploitation utile,
spécifiée par la classification de conception initiale
3.2
durée de vie de conception
estimation de la période d’exploitation admissible d’un appareil de levage, basée sur ses spécifications
de conception initiales et tenant compte des cycles de charge et des spectres de charge attendus pendant
son exploitation prévue
© ISO 2014 – Tous droits réservés 1

---------------------- Page: 6 ----------------------
ISO 12482:2014(F)

3.3
période d’activité de conception
DWP
période d’exploitation dans un service réel spécifique, durant laquelle le service de conception est atteint
3.4
évaluation spéciale
SA
examen et évaluation approfondis de l’appareil de levage ou d’un palan, à effectuer lorsque le service
réel de l’appareil de levage ou du palan approche du service de conception
3.5
révision générale
GO
toutes les opérations de remise à neuf et d’entretien basées sur une évaluation spéciale (SA), nécessaires
pour prolonger la durée de service d’un appareil de levage en toute sécurité
3.6
cycle de travail
séquence d’opérations (de manœuvre) débutant avec le levage d’une charge, son transfert, sa descente
et sa mise au sol, son détachement et le replacement de l’accessoire de levage non chargé en position de
départ, prêt à lever une autre charge
4 Enregistrement des opérations de l’appareil de levage
4.1 Généralités
Il convient que le propriétaire de l’appareil de levage conserve des enregistrements des opérations
de l’appareil de levage, qui permettent d’identifier les critères spécifiés par le fabricant de l’appareil
de levage et d’effectuer les évaluations décrites dans la présente norme. Des enregistrements des
opérations de maintenance, des inspections, des réparations, des modifications apportées à l’appareil
et des événements exceptionnels tels que les surcharges, les conditions climatiques extrêmes et les
collisions, doivent également être conservés. Il convient que les enregistrements soient mis à jour au
moins une fois par an dans le cadre des inspections périodiques, voir l’ISO 9927-1.
4.2 Méthode de comptage du service
L’estimation de l’historique du service peut être répartie dans les catégories suivantes, basées sur des
recueils de données réguliers et fiables et sur des procédures de documentation.
a) Les données du service de l’appareil de levage sont enregistrées par un système spécial prévu à cet
effet qui fonctionne toujours de manière automatique lorsque l’appareil de levage est en marche.
L’opérateur de l’appareil de levage n’a pas la possibilité d’éteindre le système d’enregistrement.
b) L’appareil de levage est fourni avec des compteurs enregistrant les données de son service.
L’utilisateur collecte et documente manuellement les données du service relevées par les compteurs.
c) L’historique du service de l’appareil de levage est calculé à partir d’un processus d’exploitation
régulier de l’appareil de levage. L’appareil de levage fait partie intégrante de ce processus. Les
données du processus sont documentées.
d) L’historique du service de l’appareil de levage est estimé à partir de données de production générales
du site d’exploitation de l’appareil de levage.
e) L’historique du service de l’appareil de levage est incomplet.
f) L’historique de l’appareil de levage est inconnu (par exemple dans le cas d’un appareil de levage
d’occasion). L’historique pour le calcul de la DWP est basé sur une estimation ou supposé être selon
2 © ISO 2014 – Tous droits réservés

---------------------- Page: 7 ----------------------
ISO 12482:2014(F)

la classification de conception et la durée de vie de conception réduite utilisant le facteur f du
1
Tableau 1, pour le cas n° 5.
Les informations de base pour le comptage du service de l’appareil de levage sont dans tous les cas
fournies par le propriétaire/l’utilisateur de l’appareil de levage.
Lorsque les instruments d’enregistrement ou compteurs sont installés, il convient que l’utilisateur
inspecte régulièrement les instruments afin de s’assurer de leur bon fonctionnement.
4.3 Facteur de sécurité pour le comptage du service
Lors du calcul de la période d’activité de conception DWP d’un appareil de levage, le service estimé à
partir de l’historique doit être multiplié par un facteur de sécurité f conformément au Tableau 1, pour
1
couvrir le manque de fiabilité de l’enregistrement et de l’estimation du service.
Tableau 1 — Facteur de sécurité f pour le comptage du service
1
N° Méthode d’enregistrement du service f
1
Système d’enregistrement automatique, 4.2 a), ou
1,0
1
Compteurs et documentation manuelle, 4.2 b)
2 Estimation basée sur un processus spécial et documenté, 4.2 c) 1,1
Estimation basée sur la production documentée du site d’exploitation de l’appareil
3 1,2
de levage, 4.2 d)
Estimation basée sur la production estimée et non documentée du site d’exploita-
4 1,3
tion de l’appareil de levage, 4.2 e)
5 Historique inconnu du service de l’appareil de levage, 4.2 f) 1,5
5 Évaluation de la période d’activité de conception (DWP)
5.1 Généralités
De nombreux composants d’un appareil de levage peuvent défaillir à cause de la fatigue du métal, qui est
difficile à prévoir ou estimer par des inspections physiques. La protection contre les défaillances dues à
la fatigue par des inspections physiques peut être difficile à cause des raisons suivantes:
— La fenêtre de temps pour une inspection en toute sécurité d’une fissure variant d’une taille détectable
jusqu’à une taille critique peut être courte, menant à des inspections fréquentes et inutiles;
— la détection d’une fissure de fatigue nécessiterait dans de nombreux cas le démontage complet d’un
composant;
— il n’est pas possible de planifier et de programmer un calendrier des futures réparations de l’appareil
de levage et une non-acceptation lors d’une inspection nécessite en général une action immédiate et
éventuellement l’arrêt de l’exploitation de l’appareil de levage.
L’objectif de l’évaluation de la DWP est d’estimer le service réel cumulé de l’appareil de levage et d’évaluer
sa durée de vie restante.
Il est supposé que
— toutes les inspections périodiques programmées pour l’appareil de levage ont été effectuées,
— tout dommage subi pendant son exploitation est enregistré et réparé de manière appropriée, et
— les opérations de maintenance, ainsi que le remplacement des pièces d’usure, sont réalisés
conformément aux instructions du fabricant.
© ISO 2014 – Tous droits réservés 3

---------------------- Page: 8 ----------------------
ISO 12482:2014(F)

5.2 Calendrier
Il convient de collecter tous les 12 mois les données d’exploitation de l’appareil de levage, ainsi que
l’évaluation de la DWP, dans le cadre des inspections périodiques (voir l’ISO 9927-1).
5.3 Méthode de calcul de la période d’activité de conception DWP
Il convient que la méthode de calcul appliquée de la DWP suive, aussi précisément que possible, la
spécification et la classification de
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.