Cranes - Offshore cranes - Part 3: Light offshore cranes

This document applies to light offshore cranes including their supporting pedestals and structures.
NOTE   The supporting pedestal and structures such as columns and boom rests are covered by this standard to the extent where their main purpose is to support the crane.
This document is applicable to light offshore cranes, whose structures are made of steel.
The following characteristics distinguish light offshore cranes from other types of offshore cranes:
-   maximum rated capacity 20 tonnes, maximum load moment 300 tm;
-   limitation for off-board lifting operation Hs = 2,0 m and wind speed 15 m/s (3s gust);
-   maximum number of working cycles class U3 (C ≤ 125.000) according to EN 13001-1.
This document gives requirements for all significant hazards, hazardous situations and events relevant to light offshore cranes, when used as intended and under conditions foreseen by the risk assessment (see Clause 4).
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping or changing the configuration of the crane;
b)   non- fixed load lifting attachments, i.e. any item between the hook and the load;
c)   lifting operations in ambient temperatures below −20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   lifting operations involving more than one crane;
f)   accidental loads due to collisions or earthquakes;
g)   emergency personnel rescue operations (except training);
h)   subsea lifting operations;
i)   general purpose offshore cranes, floating cranes and motion compensated cranes.
This document is applicable for the lifting of personnel.
This document is applicable to light offshore cranes, which are manufactured after the date of approval by CEN of this document.

Krane - Offshore-Krane - Teil 3: Offshore-Krane mit kleiner Kapazität

Dieses Dokument gilt für Offshore Krane mit kleiner Kapazität, einschließlich deren unterstützenden Trag-säulen und Fundamentstrukturen.
ANMERKUNG   Die unterstützenden Tragsäulen und Fundamentstrukturen, wie z. B. Kranmast  und Auslegerstützen, werden in dieser Norm behandelt, soweit ihre Hauptaufgabe darin besteht, den Kran zu abzustützen.
Dieses Dokument gilt für Offshore Krane mit kleiner Kapazität, deren Kranstrukturen aus Stahl gefertigt sind.
Die folgenden Merkmale unterscheiden Offshore Krane mit kleiner Kapazität von anderen Offshore Kran-arten:
-   maximale Tragfähigkeit von 20 Tonnen, maximales Lastmoment von 300 tm;
-   Begrenzung von Hubvorgängen außerhalb der Offshore Anlage auf Hs = 2,0 m bei einer Windgeschwindigkeit von 15 m/s (bei 3 s Böenwind);
-   maximale Gesamtzahl von Arbeitsspielen entsprechend Klasse U3 (C ≤ 1,25 ⤬105 Arbeitsspiele) nach EN 13001 1.
Dieses Dokument enthält Anforderungen im Hinblick auf alle signifikanten Gefährdungen, Gefährdungs-situationen und Gefährdungsereignisse, die auf Offshore Krane mit kleiner Kapazität zutreffen, wenn sie bestimmungsgemäß und unter den durch die Risikobeurteilung vorhergesehenen Bedingungen verwendet werden (siehe Abschnitt 4).
Dieses Dokument gilt nicht für:
a)   den Transport, die Montage, die Außerbetriebnahme, die Verschrottung oder die Rüstzustandsänderung des Krans;
b)   lose Lastaufnahmemittel, d. h. alle Teile zwischen dem Haken und der Last;
c)   Hubvorgänge bei Umgebungstemperaturen unter −20 °C;
d)   Hubvorgänge bei Umgebungstemperaturen über 45 °C;
e)   Hubvorgänge, an denen mehr als ein Kran beteiligt ist;
f)   unbeabsichtigte Lasten aufgrund von Kollisionen oder Erdbeben;
g)   Personenrettungsmaßnahmen in Notfällen (ausgenommen Training);
h)   Unterwasser Hebearbeiten;
i)   Offshore Krane für allgemeine Verwendung, Schwimmkrane und Krane mit Bewegungsfolgeeinrichtung.
Dieses Dokument gilt für das Heben von Personal.
Dieses Dokument gilt für Offshore Krane mit kleiner Kapazität, die nach dem Datum der Veröffentlichung dieses Dokument durch CEN hergestellt wurden.

Appareils de levage à charge suspendue - Grues off-shore - Partie 3 : Grues off-shore légères (potence off-shore)

Le présent document s’applique aux grues off-shore légères (potence off-shore), y compris à leurs socles et structures d’appui.
NOTE   Le socle et les structures d’appui comme les colonnes et supports de flèche sont couverts par la présente norme dans la mesure où leur objectif principal est de soutenir la grue.
Le présent document s’applique aux grues off-shore légères, dont les structures sont en acier.
Les caractéristiques suivantes distinguent les grues off-shore légères des autres types de grues off-shore :
-   charge nominale maximale 20 tonnes, moment de charge maximal 300 tm ;
-   limite pour les opérations de levage hors bord Hs = 2,0 m et vitesse de vent 15 m/s (rafale de 3 s) ;
-   nombre maximal de cycles de travail classe U3 (C ≤ 1,25 × 105) conformément à l’EN 13001-1.
Le présent document indique les exigences relatives à l'ensemble des phénomènes, situations et événements dangereux majeurs relatifs aux grues off-shore légères, lorsque celles-ci sont utilisées comme prévu et dans les conditions prévues par l'évaluation des risques (voir Article 4).
Le présent document ne s’applique pas :
(a)   au transport, au montage, au démontage, à la mise au rebut ou à la modification de configuration de la grue ;
b)   aux accessoires amovibles de levage de charge, c'est-à-dire tout élément entre le crochet et la charge ;
c)   aux opérations de levage à des températures ambiantes inférieures à −20 °C ;
d)   aux opérations de levage à des températures ambiantes supérieures à 45 °C ;
e)   aux opérations de levage impliquant plus d'un appareil de levage à charge suspendue ;
f)   aux charges accidentelles dues à des collisions ou à des tremblements de terre ;
g)   aux opérations de sauvetage de personnel (hors entraînement) ;
h)   aux opérations de levage sous-marines ;
i)   aux grues off-shore pour usage général, aux grues flottantes et aux grues à compensation de mouvement.
Le présent document s’applique au levage de personnel.
Le présent document s’applique aux grues off-shore légères fabriquées après la date d'approbation du présent document par le CEN.

Dvigala (žerjavi) - Dvigala na plavajočih objektih - 3. del: Lahka dvigala na plavajočih objektih

General Information

Status
Published
Public Enquiry End Date
29-Nov-2018
Publication Date
09-May-2021
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
02-Apr-2021
Due Date
07-Jun-2021
Completion Date
10-May-2021

Buy Standard

Standard
SIST EN 13852-3:2021 - BARVE na PDF-str 28,41,58,85,92,93
English language
111 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 13852-3:2021
01-junij-2021
Dvigala (žerjavi) - Dvigala na plavajočih objektih - 3. del: Lahka dvigala na
plavajočih objektih
Cranes - Offshore cranes - Part 3: Light offshore cranes
Krane - Offshore-Krane - Teil 3: Offshore-Krane mit kleiner Kapazität

Appareils de levage à charge suspendue - Grues off-shore - Partie 3 : Grues off-shore

légères (potence off-shore)
Ta slovenski standard je istoveten z: EN 13852-3:2021
ICS:
47.020.40 Dvigalna oprema in oprema Lifting and cargo handling
za pretovor equipment
53.020.20 Dvigala Cranes
SIST EN 13852-3:2021 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13852-3:2021
---------------------- Page: 2 ----------------------
SIST EN 13852-3:2021
EN 13852-3
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2021
EUROPÄISCHE NORM
ICS 47.020.40; 53.020.20
English Version
Cranes - Offshore cranes - Part 3: Light offshore cranes

Appareils de levage à charge suspendue - Grues off- Krane - Offshore-Krane - Teil 3: Offshore-Krane mit

shore - Partie 3 : Grues off-shore légères (potence off- kleiner Kapazität
shore)
This European Standard was approved by CEN on 8 February 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13852-3:2021 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)
Contents Page

European foreword .............................................................................................................................................. 4

Introduction ............................................................................................................................................................ 5

1 Scope ............................................................................................................................................................ 6

2 Normative references ............................................................................................................................ 6

3 Terms and definitions ......................................................................................................................... 12

4 List of significant hazards .................................................................................................................. 16

5 Safety requirements and/or protective measures ................................................................... 23

5.1 General ...................................................................................................................................................... 23

5.2 Strength and stability .......................................................................................................................... 25

5.3 Electrical systems ................................................................................................................................. 29

5.4 Mechanical equipment ........................................................................................................................ 33

5.5 Limiting and indicating devices ....................................................................................................... 36

5.6 Protection and emergency systems ............................................................................................... 38

5.7 User interface ......................................................................................................................................... 41

5.8 Fabrication .............................................................................................................................................. 45

5.9 Surface preparation and protective coating ............................................................................... 45

5.10 Lifting of persons .................................................................................................................................. 46

6 Verification of the safety requirements and/or protective measures .............................. 49

6.1 General ...................................................................................................................................................... 49

6.2 Testing ...................................................................................................................................................... 54

7 Information for use .............................................................................................................................. 58

7.1 General ...................................................................................................................................................... 58

7.2 Operation ................................................................................................................................................. 59

7.3 Maintenance ........................................................................................................................................... 62

7.4 Marking .................................................................................................................................................... 63

Annex A (informative) Selection of a suitable set of crane standards for a given application 64

Annex B (normative) Determination of factors ........................................................................................ 66

B.1 Calculation of the dynamic coefficient .......................................................................................... 66

B.2 Offlead and sidelead ............................................................................................................................ 68

B.3 Hook velocity .......................................................................................................................................... 69

Annex C (normative) Environmental influences ...................................................................................... 76

C.1 General ...................................................................................................................................................... 76

C.2 Atmosphere ............................................................................................................................................. 76

C.3 Temperature ........................................................................................................................................... 76

---------------------- Page: 4 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)

C.4 Wind .......................................................................................................................................................... 77

C.5 Installation motions............................................................................................................................. 77

C.6 Ice and snow loads ............................................................................................................................... 79

Annex D (normative) Failure mode analyses ............................................................................................ 80

D.1 General ..................................................................................................................................................... 80

D.2 Failure mode charts ............................................................................................................................. 80

Annex E (normative) Arrangement of controls ........................................................................................ 82

E.1 Control station (permanent location) ........................................................................................... 82

E.2 Control console (permanent location or remote) ..................................................................... 82

Annex F (normative) Requirements for brakes ........................................................................................ 83

Annex G (normative) Ranking of safety functions ................................................................................... 85

Annex H (normative) Safety functions and required performance levels ...................................... 86

Annex I (informative) Typical light offshore cranes and their terminology .................................. 87

Annex J (normative) Excursion envelopes ................................................................................................. 91

Annex K (normative) Equipment for use in a hazardous area ............................................................ 92

K.1 General ..................................................................................................................................................... 92

K.2 Avoidance or reduction of ignition sources ................................................................................ 92

K.3 Electrical equipment ........................................................................................................................... 92

K.4 Non-electrical equipment .................................................................................................................. 93

K.5 Electrostatic discharge ....................................................................................................................... 93

Annex L (informative) Light offshore crane data sheet ......................................................................... 94

Annex ZA (informative) Relationship between this European Standard and the essential

requirements of Directive 2006/42/EC aimed to be covered ........................................... 102

Annex ZB (informative) Relationship between this European Standard and the Essential

requirements of EU Directive 2014/34/EU ............................................................................. 106

Bibliography ...................................................................................................................................................... 110

---------------------- Page: 5 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)
European foreword

This document (EN 13852-3:2021) has been prepared by Technical Committee CEN/TC 147 “Cranes -

safety”, the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by September 2021, and conflicting national standards

shall be withdrawn at the latest by September 2021.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document has been prepared under a mandate given to CEN by the European Commission and

the European Free Trade Association, and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative Annex ZA or ZB, which are integral parts of this

document.
This document is one part of EN 13852. The parts are the following ones:
— Part 1: General purpose offshore cranes;
— Part 2: Floating cranes;
— Part 3: Light offshore cranes.

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,

Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey

and the United Kingdom.
---------------------- Page: 6 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)
Introduction
This document is a type C standard as defined in EN ISO 12100.

This document has been prepared to provide one means for light offshore cranes to conform to the

essential health and safety requirements of the Machinery Directive.

The machinery concerned and the extent to which hazards, hazardous situations and hazardous events

are covered and are indicated in the scope of this document (see Clause 1).

When provisions of this type C standard are different from those which are stated in type A or B

standards, the provisions of this type C standard take precedence over the provisions of the other

standards, for machines that have been designed and built according to the provisions of this type C

standard.
---------------------- Page: 7 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)
1 Scope

This document applies to light offshore cranes including their supporting pedestals and structures.

NOTE Supporting pedestal and structures such as columns and boom rests, are covered by this document

to the extent where their main purpose is to support the crane.

This document is applicable to light offshore cranes, whose structures are made of steel, and fulfil all

of the following characteristics:
— maximum rated capacity 15 tonnes or maximum static load moment 3 000 kNm;

— limitation for off-board lifting operation up to H = 2,0 m and wind speed 15 m/s (3 s gust);

— maximum number of working cycles class U (C ≤ 3,15 × 10 ) according to EN 13001-1.

This document provides requirements for all significant hazards, hazardous situations and events

relevant to light offshore cranes for lifting of goods and lifting of persons, when used as intended and

under conditions foreseen by the risk assessment (see Clause 4).

This document is applicable to light offshore cranes, which are manufactured after the date of approval

by CEN of this document.
This document is not applicable for:

a) transportation, assembly, disabling, scrapping, installation or erecting of the crane;

b) any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories,

baskets, carriers and containers;
c) lifting operations in ambient temperatures below −20 °C;
d) lifting operations in ambient temperatures above 45 °C;
e) lifting operations involving more than one crane;

f) accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by

exceptional loads defined in Table B.7;
g) emergency personnel rescue operations (except training);
h) subsea lifting operations;

i) general purpose offshore cranes (covered by EN 13852-1), floating cranes and motion

compensated cranes.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments)

applies.

EN 614-1:2006+A1:2009, Safety of machinery — Ergonomic design principles — Part 1: Terminology

and general principles
---------------------- Page: 8 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)

EN 614-2:2000+A1:2008, Safety of machinery — Ergonomic design principles — Part 2: Interactions

between the design of machinery and work tasks
EN 795:2012, Personal fall protection equipment — Anchor devices

EN 842:1996+A1:2008, Safety of machinery — Visual danger signals — General requirements, design

and testing

EN 894-1:1997+A1:2008, Safety of machinery — Ergonomics requirements for the design of displays and

control actuators — Part 1: General principles for human interactions with displays and control

actuators

EN 894-2:1997+A1:2008, Safety of machinery — Ergonomics requirements for the design of displays and

control actuators — Part 2: Displays

EN 894-3:2000+A1:2008, Safety of machinery — Ergonomics requirements for the design of displays and

control actuators — Part 3: Control actuators

EN 1127-1:2019, Explosive atmospheres — Explosion prevention and protection — Part 1: Basic

concepts and methodology
EN 1837:2020, Safety of machinery — Integral lighting of machines
EN 10204:2004, Metallic products — Types of inspection documents

EN 12077-2:1998+A1:2008, Cranes safety — Requirements for health and safety — Part 2: Limiting and

indicating devices

EN 12385-1:2002+A1:2008, Steel wire ropes — Safety — Part 1: General requirements

EN 12385-2:2002+A1:2008, Steel wire ropes — Safety — Part 2: Definitions, designation and

classification

EN 12385-3:2020, Steel wire ropes — Safety — Part 3: Information for use and maintenance

EN 12385-4:2002+A1:2008, Steel wire ropes — Safety — Part 4: Stranded ropes for general lifting

applications

EN 12464-2:2014, Light and lighting — Lighting of work places — Part 2: Outdoor work places

EN 12644-1:2001+A1:2008, Cranes — Information for use and testing — Part 1: Instructions

EN 12644-2:2000+A1:2008, Cranes — Information for use and testing — Part 2: Marking

EN 13001-1:2015, Cranes — General design — Part 1: General principles and requirements

EN 13001-2:2014, Crane safety — General design — Part 2: Load actions

EN 13001-3-1:2012+A2:2018, Cranes — General design — Part 3-1: Limit states and proof of

competence of steel structure

EN 13001-3-2:2014, Cranes — General design — Part 3-2: Limit states and proof of competence of wire

ropes in reeving systems
---------------------- Page: 9 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)

EN 13001-3-3:2014, Cranes — General design — Part 3-3: Limit states and proof of competence of

wheel/rail contacts

EN 13001-3-4:2018, Cranes — General design — Part 3-4: Limit states and proof of competence of

machinery bearings

EN 13001-3-5:2016, Cranes — General design — Part 3-5: Limit states and proof of competence of forged

hooks

EN 13001-3-6:2018, Cranes — General design — Part 3-6: Limit states and proof of competence of

machinery — Hydraulic cylinders
EN 13135:2013+A1:2018, Cranes — Safety — Design — Requirements for equipment
EN 13557:2003+A2:2008, Cranes — Controls and control stations
EN 13586:2020, Cranes — Access

EN ISO 13732-1:2008, Ergonomics of the thermal environment — Methods for the assessment of human

responses to contact with surfaces — Part 1: Hot surfaces (ISO 13732-1:2006)

EN ISO 14118:2018, Safety of machinery — Prevention of unexpected start-up (ISO 14118:2017)

EN 14502-1:2010, Cranes — Equipment for the lifting of persons — Part 1: Suspended baskets

EN IEC 60079-0:2018, Explosive atmospheres — Part 0: Equipment — General requirements

(IEC 60079-0:2017)

EN 60079-1:2014, Explosive atmospheres — Part 1: Equipment protection by flameproof enclosures “d”

(IEC 60079-1:2014)

EN 60079-2:2014, Explosive atmospheres — Part 2: Equipment protection by pressurized enclosure “p”

(IEC 60079-2:2014)

EN 60079-5:2015, Explosive atmospheres — Part 5: Equipment protection by powder filling “q”

(IEC 60079-5:2015)

EN 60079-6:2015, Explosive atmospheres — Part 6: Equipment protection by liquid immersion “o”

(IEC 60079-6:2015)

EN 60079-7:2015, Explosive atmospheres — Part 7: Equipment protection by increased safety “e”

(IEC 60079-7:2015)

EN 60079-11:2012, Explosive atmospheres — Part 11: Equipment protection by intrinsic safety “i”

(IEC 60079-11:2011)
This document is impacted by EN 60079-1:2014/AC:2018-09.
This document is impacted by EN 60079-7:2015/A1:2018.
---------------------- Page: 10 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)

EN 60079-14:2014, Explosive atmospheres — Part 14: Electrical installations design, selection and

erection (IEC 60079-14:2013)

EN 60079-18:2015, Explosive atmospheres — Part 18: Equipment protection by encapsulation “m”

(IEC 60079-18:2014)

EN 60079-25:2010, Explosive atmospheres — Part 25: Intrinsically safe electrical systems

(IEC 60079-25:2010)

EN 60204-32:2008, Safety of machinery — Electrical equipment of machines — Part 32: Requirements

for hoisting machines (IEC 60204-32:2008)

EN IEC 61000-6-2:2019, Electromagnetic compatibility (EMC) — Part 6-2: Generic standards —

Immunity for industrial environments (IEC 61000-6-2:2016)

EN IEC 61000-6-4:2019, Electromagnetic compatibility (EMC) — Part 6-4: Generic standards —

Emission standard for industrial environments (IEC 61000-6-4:2018)

EN ISO 898-1:2013, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1:

Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread

(ISO 898-1:2013)

EN ISO 3744:2010, Acoustics — Determination of sound power levels and sound energy levels of noise

sources using sound pressure — Engineering methods for an essentially free field over a reflecting plane

(ISO 3744:2010)

EN ISO 3834-1:2005, Quality requirements for fusion welding of metallic materials — Part 1: Criteria for

the selection of the appropriate level of quality requirements (ISO 3834-1:2005)

EN ISO 3834-2:2005, Quality requirements for fusion welding of metallic materials — Part 2:

Comprehensive quality requirements (ISO 3834-2:2005)

EN ISO 3834-3:2005, Quality requirements for fusion welding of metallic materials — Part 3: Standard

quality requirements (ISO 3834-3:2005)

EN ISO 4413:2010, Hydraulic fluid power — General rules and safety requirements for systems and their

components (ISO 4413:2010)

EN ISO 4414:2010, Pneumatic fluid power — General rules and safety requirements for systems and their

components (ISO 4414:2010)

EN ISO 4871:2009, Acoustics — Declaration and verification of noise emission values of machinery and

equipment (ISO 4871:1996)

EN ISO 7731:2008, Ergonomics — Danger signals for public and work areas — Auditory danger signals

(ISO 7731:2003)

This document is impacted by EN 60079-18:2010/A1:2017 and EN 60079-18:2010/AC:2018-09.

This document is impacted by EN 60079-25:2010/AC:2013.
---------------------- Page: 11 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)

EN ISO 11201:2010, Acoustics — Noise emitted by machinery and equipment — Determination of

emission sound pressure levels at a work station and at other specified positions in an essentially free field

over a reflecting plane with negligible environmental corrections (ISO 11201:2010)

EN ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk

reduction (ISO 12100:2010)

EN ISO 13849-1:2015, Safety of machinery — Safety-related parts of control systems — Part 1: General

principles for design (ISO 13849-1:2015)

EN ISO 13850:2015, Safety of machinery — Emergency stop function — Principles for design

(ISO 13850:2015)

EN ISO 13857:2019, Safety of machinery — Safety distances to prevent hazard zones being reached by

upper and lower limbs (ISO 13857:2019)

EN ISO 14120:2015, Safety of machinery — Guards — General requirements for the design and

construction of fixed and movable guards (ISO 14120:2015)

EN ISO 15614-1:2017, Specification and qualification of welding procedures for metallic materials —

Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys

(ISO 15614-1:2017, Corrected version 2017-10-01)

EN ISO 15614-11:2002, Specification and qualification of welding procedures for metallic materials —

Welding procedure test — Part 11: Electron and laser beam welding (ISO 15614-11:2002)

EN ISO 15614-12:2014, Specification and qualification of welding procedures for metallic materials —

Welding procedure test — Part 12: Spot, seam and projection welding (ISO 15614-12:2014)

EN ISO 15614-13:2012, Specification and qualification of welding procedures for metallic materials —

Welding procedure test — Part 13: Upset (resistance butt) and flash welding (ISO 15614-13:2012)

EN ISO 19353:2019, Safety of machinery — Fire prevention and fire protection (ISO 19353:2019)

EN ISO 80079-36:2016, Explosive atmospheres — Part 36: Non-electrical equipment for explosive

atmospheres — Basic method and requirements (ISO 80079-36:2016)

EN ISO 80079-37:2016, Explosive atmospheres — Part 37: Non-electrical equipment for explosive

atmospheres — Non-electrical type of protection constructional safety “c”, control of ignition sources “b”,

liquid immersion “k” (ISO 80079-37:2016)

EN 60529:1991, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989)

EN 61310-1:2008, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for

visual, acoustic and tactile signals (IEC 61310-1:2007)

EN 61310-2:2008, Safety of machinery — Indication, marking and actuation — Part 2: Requirements for

marking (IEC 61310-2:2007)

As impacted by EN60529:1991/AC:2006-12, EN60529:1991/A1:2000, EN60529:1991/A2:2013 and

EN60529:1991/A2:2013/AC:2019-02.
---------------------- Page: 12 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)

EN 61310-3:2008, Safety of machinery — Indication, marking and actuation — Part 3: Requirements for

the location and operation of actuators (IEC 61310-3:2007)

ISO 3864-1:2011, Graphical symbols — Safety colours and safety signs — Part 1: Design principles for

safety signs and safety markings

ISO 3864-2:2016, Graphical symbols — Safety colours and safety signs — Part 2: Design principles for

product safety labels

ISO 3864-3:2012, Graphical symbols — Safety colours and safety signs — Part 3: Design principles for

graphical symbols for use in safety signs

ISO 3864-4:2011, Graphical symbols — Safety colours and safety signs — Part 4: Colorimetric and

photometric properties of safety sign materials

ISO 5817:2014, Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding

excluded) — Quality levels for imperfections

ISO 7010:2019, Graphical symbols — Safety colours and safety signs — Registered safety signs

ISO 9927-1:2013, Cranes — Inspections — Part 1: General
ISO 12478-1:1997, Cranes — Maintenance manual — Part 1: General
ISO 12480-1:1997, Cranes — Safe use — Part 1: General
ISO 12482:2014, Cranes — Monitoring for crane design working period

EN ISO 12944-1:2017, Paints and varnishes — Corrosion protection of steel structures by protective

paint systems — Part 1: General introduction (ISO 12944-1:2017)

EN ISO 12944-2:2017, Paints and varnishes — Corrosion protection of steel structures by protective

paint systems — Part 2: Classification of environments (ISO 12944-2:2017)

EN ISO 12944-3:2017, Paints and varnishes — Corrosion protection of steel structures by protective

paint systems — Part 3: Design considerations (ISO 12944-3:2017)

EN ISO 12944-4:2017, Paints and varnishes — Corrosion protection of steel structures by protective

paint systems — Part 4: Types of surface and surface preparation (ISO 12944-4:2017)

EN ISO 12944-5:2019, Paints and varnishes — Corrosion protection of steel structures by protective

paint systems — Part 5: Protective paint systems (ISO 12944-5:2019)

EN ISO 12944-6:2018, Paints and varnishes — Corrosion protection of steel structures by protective

paint systems — Part 6: Laboratory performance test methods (ISO 12944-6:2018)

EN ISO 12944-7:2017, Paints and varnishes — Corrosion protection of steel structures by protective

paint systems — Part 7: Execution and supervision of paint work (ISO 12944-7:2017)

EN ISO 12944-8:2017, Paints and varnishes — Corrosion protection of steel structures by protective

paint systems — Part 8: Development of specifications for new work and maintenance (ISO 12944-

8:2017)
---------------------- Page: 13 ----------------------
SIST EN 13852-3:2021
EN 13852-3:2021 (E)

EN ISO 12944-9:2018, Paints and varnishes — Corrosion protection of steel structures by protective

paint systems — Part 9: Protective paint systems and laboratory performance test methods for offshore

and related structures (ISO 12944-9:2018)

ISO 17635:2016, Non-destructive testing of welds — General rules for metallic materials

ISO 20332:2016, Cranes — Proof of competence of steel structures
ISO 23815-1:2007, Cranes —Maintenance — Part 1: General
3 Terms and definitions
For the purposes of this document, the terms and definit
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.