SIST EN ISO 11339:2022

Adhesives - T-peel test for flexible-to-flexible bonded assemblies (ISO 11339:2022)

This document specifies a T‑peel test for the determination of the peel resistance of an adhesive by
measuring the peeling force of a T‑shaped bonded assembly of two flexible adherends. This test
procedure does not provide design information.
NOTE This method was originally developed for use with metal adherends but other, flexible, adherends can
also be used.

Klebstoffe - T-Schälprüfung für geklebte Verbindungen aus flexiblen Fügeteilen (ISO 11339:2022)

Dieses Dokument legt eine T-Schälprüfung fest für die Bestimmung des Schälwiderstands eines Klebstoffes durch Messung der Schälkraft einer T-förmigen Klebung zweier flexibler Fügeteile. Dieses Prüfverfahren liefert keine Informationen zur Konstruktion.
ANMERKUNG   Dieses Verfahren wurde ursprünglich für Metallfügeteile entwickelt, aber andere, flexible, Fügeteile können ebenso verwendet werden.
SICHERHEITSHINWEIS — Die Anwender dieses Dokuments sollten, sofern zutreffend, mit der üblichen Laborpraxis vertraut sein. Dieses Dokument beansprucht nicht, alle mit seiner Anwendung verbundenen Sicherheitsprobleme, soweit diese gegeben sind, zu behandeln. Es liegt in der Verantwortung des Anwenders, vor der Anwendung angemessene Sicherheitsvorkehrungen und Gesundheitsschutzmaßnahmen einzuleiten und die Anwendbarkeit aller regulatorischen Rahmenbedingungen zu ermitteln.
Es ist anerkannt, dass einige der in diesem Dokument zugelassenen Materialien negative Auswirkungen auf die Umwelt haben können. Sobald der technische Fortschritt zu annehmbaren Alternativen für diese Materialien führt, werden diese, so weit wie möglich, aus diesem Dokument entfernt.
Am Ende der Prüfung sollte für eine geeignete Entsorgung der Abfälle Sorge getragen werden.

Adhésifs - Essai de pelage en T d'assemblages collés flexible sur flexible (ISO 11339:2022)

Le présent document spécifie un essai de pelage en T pour la détermination de la résistance au pelage d’un adhésif par mesurage de la force de pelage d’un assemblage collé en forme de T, formé de deux supports flexibles. Ce mode opératoire d’essai ne fournit aucune information concernant la conception.
NOTE            Cette méthode a été mise au point à l’origine pour des supports métalliques, mais elle peut également être utilisée pour d’autres supports flexibles.

Lepila - T-preskus luščenja za lepljenje dveh gibkih lepljencev (ISO 11339:2022)

Ta dokument določa T preskus luščenja za določevanje odpornosti lepila proti razslojevanju z merjenjem sile luščenja lepljenega spoja dveh gibkih lepljencev v obliki T. Ta preskusni postopek ne podaja informacij o zasnovi. OPOMBA: Ta metoda je bila prvotno razvita za uporabo s kovinskimi lepljenci, vendar je mogoče uporabiti tudi druge, gibke lepljence.

General Information

• Status: Published
• Public Enquiry End Date: 29-Dec-2021
• Publication Date: 23-Feb-2022
• ICS: 83.180 - Adhesives
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 23-Feb-2022
• Due Date: 30-Apr-2022
• Completion Date: 24-Feb-2022
• Ref Project: EN ISO 11339:2022 - Adhesives - T-peel test for flexible-to-flexible bonded assemblies (ISO 11339:2022)

Relations

• Replaces: SIST EN ISO 11339:2011 - Adhesives - T-peel test for flexible-to-flexible bonded assemblies (ISO 11339:2010)
• Effective Date: 23-Feb-2022
• Replaces: SIST EN ISO 11339:2011 - Adhesives - T-peel test for flexible-to-flexible bonded assemblies (ISO 11339:2010)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11339:2022
01-april-2022
Nadomešča:
SIST EN ISO 11339:2011
Lepila - T-preskus luščenja za lepljenje dveh gibkih lepljencev (ISO 11339:2022)
Adhesives - T-peel test for flexible-to-flexible bonded assemblies (ISO 11339:2022)
Klebstoffe - T-Schälprüfung für geklebte Verbindungen aus flexiblen Fügeteilen (ISO
11339:2022)
Adhésifs - Essai de pelage en T d'assemblages collés flexible sur flexible (ISO
11339:2022)
Ta slovenski standard je istoveten z: EN ISO 11339:2022
ICS:
83.180 Lepila Adhesives
SIST EN ISO 11339:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 11339:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 11339:2022


EN ISO 11339
EUROPEAN STANDARD

NORME EUROPÉENNE

February 2022
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN ISO 11339:2010
English Version

Adhesives - T-peel test for flexible-to-flexible bonded
assemblies (ISO 11339:2022)
Adhésifs - Essai de pelage en T d'assemblages collés Klebstoffe - T-Schälprüfung für geklebte Verbindungen
flexible sur flexible (ISO 11339:2022) aus flexiblen Fügeteilen (ISO 11339:2022)
This European Standard was approved by CEN on 1 February 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11339:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 11339:2022
EN ISO 11339:2022 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 11339:2022
EN ISO 11339:2022 (E)
European foreword
This document (EN ISO 11339:2022) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by
UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2022, and conflicting national standards shall
be withdrawn at the latest by August 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11339:2010.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11339:2022 has been approved by CEN as EN ISO 11339:2022 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 11339:2022

---------------------- Page: 6 ----------------------
SIST EN ISO 11339:2022
INTERNATIONAL ISO
STANDARD 11339
Fourth edition
2022-02
Adhesives — T-peel test for flexible-to-
flexible bonded assemblies
Adhésifs — Essai de pelage en T d'assemblages collés flexible sur
flexible
Reference number
ISO 11339:2022(E)
© ISO 2022

---------------------- Page: 7 ----------------------
SIST EN ISO 11339:2022
ISO 11339:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2022 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 11339:2022
ISO 11339:2022(E)
Contents  Page
Foreword .iv
1 Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Principle . 2
5  Apparatus . 2
6  Test specimens . 2
7  Procedure .3
8  Expression of results . 4
9  Precision . 4
10 Test report . 4
Bibliography . 6
iii
© ISO 2022 – All rights reserved

---------------------- Page: 9 ----------------------
SIST EN ISO 11339:2022
ISO 11339:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 193, Adhesives, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 11339:2010), of which it constitutes a
minor revision.
The changes are as follows:
a) the term “peel strength” is replaced by the term “peel resistance” in the whole text;
b) the text has been editorially revised and the references has been updated.
Any feedback or questions on this docume
...

SLOVENSKI STANDARD
oSIST prEN ISO 11339:2021
01-december-2021
Lepila - T-preskus luščenja za lepljenje dveh gibkih lepljencev (ISO/FDIS
11339:2021)
Adhesives - T-peel test for flexible-to-flexible bonded assemblies (ISO/FDIS 11339:2021)
Klebstoffe - T-Schälprüfung für geklebte Verbindungen aus flexiblen Fügeteilen
(ISO/FDIS 11339:2021)
Adhésifs - Essai de pelage en T d'assemblages collés flexible sur flexible (ISO/FDIS
11339:2021)
Ta slovenski standard je istoveten z: prEN ISO 11339
ICS:
83.180 Lepila Adhesives
oSIST prEN ISO 11339:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 11339:2021

---------------------- Page: 2 ----------------------
oSIST prEN ISO 11339:2021
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 11339
ISO/TC 61/SC 11
Adhesives — T-peel test for flexible-to-
Secretariat: JISC
flexible bonded assemblies
Voting begins on:
2021-10-08
Adhésifs — Essai de pelage en T d'assemblages collés flexible sur
flexible
Voting terminates on:
2021-12-31
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 11339:2021(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2021

---------------------- Page: 3 ----------------------
oSIST prEN ISO 11339:2021
ISO/FDIS 11339:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 11339:2021
ISO/FDIS 11339:2021(E)
Contents  Page
Foreword .iv
1 Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Principle . 2
5  Apparatus . 2
6  Test specimens . 2
7  Procedure .3
8  Expression of results . 4
9  Precision . 4
10 Test report . 4
Bibliography . 6
iii
© ISO 2021 – All rights reserved

---------------------- Page: 5 ----------------------
oSIST prEN ISO 11339:2021
ISO/FDIS 11339:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 193, Adhesives, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 11339:2010), of which it constitutes a
minor revision.
The changes compared to the previous edition are as follows:
a) the term “peel strength” is replaced by the term “peel resistance” in the whole text.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2021 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 11339:2021
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 11339:2021(E)
Adhesives — T-peel test for flexible-to-flexible bonded
assemblies
SAFETY STATEMENT — Persons using this document should be familiar with normal laboratory
practice, if applicable. This document does not purport to address all of the safety problems, if
any, associated with its use. It is the responsibility of the user to establish appropriate safety
and health practices and determine the applicability of any regulatory conditions prior to use.
It is recognized that some of the materials permitted in this document may have a negative
environmental impact. As technological advances lead to more acceptable alternatives for such
materials, they will be eliminated to the greatest extent possible.
At the end of the test, care should be taken to dispose of all waste in an appropriate manner.
1 Scope
This document specifies a T‑peel test for the determination of the peel resistance of an adhesive by
measuring the peeling force of a T‑shaped bonded assembly of two flexible adherends. This test
procedure does not provide design information.
NOTE This method was originally developed for use with metal adherends but other, flexible, adherends can
also be used.
2  Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the late
...