SIST EN 14540:2004+A1:2007
(Main)Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
This European Standard specifies the requirements and test methods for non-percolating layflat hoses for fixed systems. The hoses are intended for use at a maximum working pressure of 1,5 MPa over a range of inside diameters from 25 mm to 52 mm. The standard applies exclusively to hoses for fire-fighting purposes intended for use at a minimum ambient temperature of -20 °C in normal conditions, and a minimum temperature of -30 °C in colder climatic conditions. Hoses conforming to this standard should be used with fire hose couplings conforming to the relevant national standards for couplings. !Hoses in marine applications and/or aggressive environments to be used with wall hydrants as specified in EN 671-2 can conform to the requirements of this standard."
Feuerlöschschläuche - Flachschläuche für Wandhydranten
Diese Europäische Norm legt die Anforderungen und Prüfverfahren für Flachschläuche für Wandhydranten fest. Die Schläuche sind für den Einsatz bei einem maximalen Arbeitsdruck von 1,5 MPa und für Innendurchmesser von 25 mm bis 52 mm vorgesehen.
Die Norm gilt ausschließlich für Schläuche für Feuerlöschzwecke, die für den Einsatz bei einer niedrigsten Temperatur von -20 °C unter normalen Bedingungen und einer niedrigsten Temperatur von -30 °C bei kälteren klimatischen Bedingungen vorgesehen sind.
Schläuche, die dieser Norm entsprechen, sollten mit Feuerlöschschlauchkupplungen verwendet werden, die den jeweiligen nationalen Normen für Kupplungen entsprechen.
! Schläuche für den Einsatz auf Schiffen und/oder in aggressiven Umgebungen zur Verwendung in Wandhy¬dranten nach EN 671-2 können den Anforderungen dieser Norm entsprechen. "
ANMERKUNG Alle Drücke sind Manometerdrücke und werden in Megapascal angegeben. )
Tuyaux de lutte contre l'incendie - Tuyaux aplatissables étanches pour systemes fixes
La présente Norme européenne spécifie les prescriptions et méthodes d'essai relatives aux tuyaux aplatissables étanches pour systemes fixes. Ces tuyaux sont destinés a etre utilisés a une pression maximale de 1,5 MPa et dans une plage de diametres comprise entre 25 mm et 52 mm.
La norme s'applique exclusivement aux tuyaux de lutte contre l'incendie destinés a etre utilisés a une température minimale de - 20 °C dans des conditions normales, et a une température minimale de -30 °C dans des conditions climatiques plus froides.
Il convient que les tuyaux conformes a la présente norme soient utilisés avec des raccords type incendie conformes aux normes nationales relatives a ces raccords.
!Si les tuyaux pour applications marines et/ou environnements agressifs sont utilisés avec des postes d’eau muraux tels que spécifiés dans l’EN 671-2, ils peuvent etre conformes aux prescriptions énoncées dans la présente norme."
NOTE Toutes les pressions sont des pressions manométriques et sont exprimées en mégapascals ).
Gasilske cevi – Gasilske poltoge tlačne cevi za vgrajene sisteme
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fire-fighting hoses - Non-percolating layflat hoses for fixed systemsTuyaux de lutte contre l'incendie - Tuyaux aplatissables étanches pour systemes fixesFeuerlöschschläuche - Flachschläuche für WandhydrantenTa slovenski standard je istoveten z:EN 14540:2004+A1:2007SIST EN 14540:2004+A1:2007en;fr;de23.040.70Gumene cevi in armatureHoses and hose assemblies13.220.10Gašenje požaraFire-fightingICS:SLOVENSKI
STANDARDSIST EN 14540:2004+A1:200701-julij-2007
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14540:2004+A1
April 2007 ICS 13.220.10; 23.040.70 Supersedes EN 14540:2004English Version
Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
Tuyaux de lutte contre l'incendie - Tuyaux aplatissables étanches pour systèmes fixes
Feuerlöschschläuche - Flachschläuche für WandhydrantenThis European Standard was approved by CEN on 1 August 2003 and includes Amendment 1 approved by CEN on 12 March 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14540:2004+A1:2007: E
EN 14540:2004+A1:2007 (E) 2 Contents Foreword.4 Introduction.5 1 Scope.6 2 Normative references.6 3 Terms and definitions.6 4 Materials and construction of hose.7 5 Dimensions, tolerances and maximum mass.7 5.1 Inside diameter and maximum mass.7 5.2 Length and tolerances on length.7 6 Performance requirements of finished hose.8 6.1 Hydrostatic requirements.8 6.2 Adhesion.9 6.3 Accelerated ageing.9 6.4 Low temperature flexibility.9 6.5 Hot surface resistance.10 6.6 Resistance to kinking.10 7 !!!!Frequency of testing.10 8 Marking.10 Annex A (normative)
Kink pressure test.11 A.1 Principle.11 A.2 Test piece.11 A.3 Apparatus.11 A.4 Procedure.11 A.5 Test report.11 Annex B (normative)
Accelerated ageing test.12 B.1 Test piece.12 B.2 Procedure.12 B.3 Test report.12 Annex C (normative)
Low temperature flexibility test.13 C.1 Test piece.13 C.2 Apparatus.13 C.3 Procedure.17 C.4 Test report.17 Annex D (normative)
Hot surface resistance test.18 D.1 Test piece.18 D.2 Apparatus.18 D.3 Procedure.21 D.4 Test report.21 Annex E (normative)
Test for resistance to kinking.22 E.1 Test piece.22 E.2 Apparatus.22 E.3 Procedure.23 E.4 Test report.23
EN 14540:2004+A1:2007 (E) 3 Annex F (normative) !Frequencies of testing (type test and production test).24 Annex G (informative) !Frequencies of testing (batch test).25 Bibliography.26
EN 14540:2004+A1:2007 (E) 4 Foreword This document (EN 14540:2004+A1:2007) has been prepared by Technical Committee CEN/TC 192 “Fire service equipment”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2007 and conflicting national standards shall be withdrawn at the latest by October 2007. This document includes Amendment 1, approved by CEN on 2007-03-12. This document supersedes EN 14540:2004. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! " The standard is based on recommendations from CEN/TC 191 “Fixed fire fighting systems” and should be read in conjunction with EN 671-2. !deleted text" At present there is no existing ISO standard on the same subject. !deleted text". Users of this European Standard are advised to consider the desirability of independent certification of product conformity with this European Standard based on testing and continuing surveillance, which may be coupled with assessment of a supplier's quality systems against EN ISO 9001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 14540:2004+A1:2007 (E) 5 Introduction A fixed system is a manually operated unit installed in a building in order to make it possible for the occupants to control and extinguish a small fire. The system consists of fixed units mounted on walls or in cabinets permanently connected to a water supply. The fixed units are composed of a coupling, a valve with a pressure indicator, a layflat water filled hose with its support and a nozzle.
EN 14540:2004+A1:2007 (E) 6 1 Scope This European Standard specifies the requirements and test methods for non-percolating layflat hoses for fixed systems. The hoses are intended for use at a maximum working pressure of 1,5 MPa over a range of inside diameters from 25 mm to 52 mm. The standard applies exclusively to hoses for fire-fighting purposes intended for use at a minimum ambient temperature of -20 °C in normal conditions, and a minimum temperature of -30 °C in colder climatic conditions. Hoses conforming to this standard should be used with fire hose couplings conforming to the relevant national standards for couplings. !Hoses in marine applications and/or aggressive environments to be used with wall hydrants as specified in EN 671-2 can conform to the requirements of this standard." NOTE All pressures are gauge pressures and are expressed in megapascals1. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 28033, Rubber and plastics hoses — Determination of adhesion between components (ISO 8033:1991). EN ISO 1307, Rubber and plastics hoses for general purpose industrial applications — Bore diameters and tolerances, and tolerances on length (ISO 1307:1992). EN ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing (ISO 1402:1994). EN ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of dimensions (ISO 4671:1999). EN ISO 8330:2000, Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:1998). ISO 188, Rubber, vulcanised or thermoplastic — Accelerated ageing or heat resistance tests. 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN ISO 8330:2000 and the following apply.
1 1 MPa = 10 bar
EN 14540:2004+A1:2007 (E) 7 3.1 layflat hose hose with a soft wall which, when unpressurized internally, collapses to such an extent that the inner faces of the inside diameter make contact and the hose takes up a flat cross-sectional appearance 3.2 jacket circular woven seamless reinforcement 4 Materials and construction of hose The hose shall be uncovered. It shall consist of the following: an impermeable rubber or plastics lining; a synthetic fibre jacket. NOTE 1 The hose jacket can be dyed or pigmented. NOTE 2 The hose manufacturer should weave the jacket and assemble the jacket and lining. NOTE 3 The lining should be as smooth as possible so as to minimize friction. 5 Dimensions, tolerances and maximum mass 5.1 Inside diameter and maximum mass The inside diameter of the hose and tolerances when measured in accordance with EN ISO 4671 shall conform to the requirements given in Table 1. The mass per metre length for a length of hose of at least 2 m, without couplings fitted, shall not exceed the value given in Table 1. Table 1 — Inside diameter, tolerances on inside diameter and maximum mass per unit length Inside diameter Tolerances for inside diameter Mass per unit length
kg/m mm mm max. 25 -0,5 to +1,0 0,18 38
0,24 40/42/45 -0,5 to +1,5 0,29 50/51/52
0,35
5.2 Length and tolerances on length The total length of hose supplied shall be in accordance with the purchaser’s requirements and shall be stated in metres. Tolerances on length shall be in accordance with EN ISO 1307. NOTE The coil or flake size, and the test procedures to determine these can, if considered necessary, be agreed between the manufacturer and purchaser.
EN 14540:2004+A1:2007 (E) 8 6 Performance requirements of finished hose 6.1 Hydrostatic requirements 6.1.1 Deformation under normal working pressure The dimensional stability of the hose when tested in accordance with EN ISO 1402, shall conform to the requirements of Tables 2 and 3. The initial test pressure shall be 0,07 MPa, and the final test pressure shall be 1,0 MPa. The twisting line shall be clockwise. Table 2 — Change in length and external diameter
Tolerances
% Change in length 0,0 to +5,0 Change in external diameter 0,0 to +5,0
Table 3 — Twisting line Inside diameter Maximum twist mm °/m 25 120 38 to 52 inclusive 100
6.1.2 Deformation under proof pressure A proof pressure hold test shall be carried out on three hose lengths each of 1 m in accordance with EN ISO 1402. The proof pressure shall be as given in Table 4 and on examination during the test, the test pieces shall not show any evidence of leakage, cracking, abrupt distortion or other signs of failure.
Table 4 — Working pressure
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.