iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1501-1:2011/kFprA1:2014

(Amendment)

Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles

Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles

This European Standard applies to rear loaded refuse collection vehicles (RCV), as defined in 3.2. This European Standard deals with all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.This European Standard is applicable to the design and construction of the rear loaded RCV so as to ensure that it is fit for its function and can be operated adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the rear loaded RCV.This part 1 describes and defines the safety requirements of rear loaded RCV excluding the interface tailgate/discharge door with the lifting device(s) and the lifting device(s) as illustrated in Figure A.1.Safety requirements for the lifting device(s) and the interface with the tailgate/discharge door are defined in prEN 1501-5.This European Standard is not applicable to:- operation in severe conditions e.g. extreme environmental conditions such as:- below - 25 °C and above + 40 °C temperatures;- tropical environment;- wind velocity in excess of 75 km/h;- contaminating environment;- corrosive environment;- operation in potentially explosive atmospheres;- handling of loads the nature of which could lead to dangerous situations (e.g. hot wastes, acids and bases, radioactive materials, contaminated waste, especially fragile loads, explosives);- operation on ships.This European Standard is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

Abfallsammelfahrzeuge und die dazugehörigen Schüttungen - Allgemeine Anforderungen und Sicherheitsanforderungen - Teil 1: Hecklader

Bennes de collecte des déchets - Exigences générales et exigences de sécurité - Partie 1 : Bennes à chargement arrière

Vozila za zbiranje odpadkov - Splošne in varnostne zahteve - 1. del: Vozila za zbiranje odpadkov z nakladanjem zadaj

General Information

Status
Not Published
Public Enquiry End Date
14-Oct-2014
ICS
13.030.40 - Installations and equipment for waste disposal and treatment
43.160 - Special purpose vehicles
Technical Committee
I13 - Imaginarni 13
Current Stage
98 - Abandoned project (Adopted Project)
Start Date
08-Oct-2019
Due Date
13-Oct-2019
Completion Date
08-Oct-2019
Ref Project
EN 1501-1:2011/FprA1 - Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles

Relations

Consolidated By
SIST EN 1501-1:2011+A1:2015 - Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
Effective Date
18-Jan-2023
Amends
SIST EN 1501-1:2011 - Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
Effective Date
01-Sep-2014
Consolidated By
SIST EN 1501-1:2011+A1:2015 - Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
Effective Date
19-Jan-2023
Consolidated By
SIST EN 1501-1:2011+A1:2015 - Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
Effective Date
01-Jun-2015

Buy Standard

EN 1501-1:2011/kFprA1:2014EN 1501-1:2011/kFprA1:2014
PreviousNext
Draft
EN 1501-1:2011/kFprA1:2014
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1501-1:2011/kFprA1:2014
01-september-2014
Vozila za zbiranje odpadkov - Splošne in varnostne zahteve - 1. del: Vozila za
zbiranje odpadkov z nakladanjem zadaj
Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear
loaded refuse collection vehicles
Abfallsammelfahrzeuge und die dazugehörigen Schüttungen - Allgemeine
Anforderungen und Sicherheitsanforderungen - Teil 1: Hecklader
Bennes de collecte des déchets - Exigences générales et exigences de sécurité - Partie
1 : Bennes à chargement arrière
Ta slovenski standard je istoveten z: EN 1501-1:2011/FprA1
ICS:
13.030.40 Naprave in oprema za Installations and equipment
odstranjevanje in obdelavo for waste disposal and
odpadkov treatment
43.160 Vozila za posebne namene Special purpose vehicles
SIST EN 1501-1:2011/kFprA1:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1501-1:2011/kFprA1:2014

---------------------- Page: 2 ----------------------

SIST EN 1501-1:2011/kFprA1:2014

EUROPEAN STANDARD
FINAL DRAFT
EN 1501-1:2011
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
July 2014
ICS 43.160
English Version
Refuse collection vehicles - General requirements and safety
requirements - Part 1: Rear loaded refuse collection vehicles
Bennes de collecte des déchets - Exigences générales et Abfallsammelfahrzeuge und die dazugehörigen
exigences de sécurité - Partie 1 : Bennes à chargement Schüttungen - Allgemeine Anforderungen und
arrière Sicherheitsanforderungen - Teil 1: Hecklader
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 183.

This draft amendment A1, if approved, will modify the European Standard EN 1501-1:2011. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1501-1:2011/FprA1:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1501-1:2011/kFprA1:2014
EN 1501-1:2011/FprA1:2014 (E)
Contents Page
Foreword .3
1 Modification to Clause 2, Normative references .4
2 Modification to 5.2.3.3, Guide flap.4
3 Modifications to 5.2.3.6, Protective devices .4
4 Modifications to 5.10.3.1, Footboards .4
5 Modifications to 5.10.3.3, Provisions for footboard(s).5
6 Modification to 5.15.1, General .5
7 Modification to 7.1.1.2, Visual .5
8 Modifications to Annex B (normative), Open and closed systems – Footboard(s) .5

2

---------------------- Page: 4 ----------------------

SIST EN 1501-1:2011/kFprA1:2014
EN 1501-1:2011/FprA1:2014 (E)
Foreword
This document (EN 1501-1:2011/FprA1:2014) has been prepared by Technical Committee CEN/TC 183
“Waste management”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been pr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1501-4:2023(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles
EN 1501-4:2023

This European Standard provides all of the information required in order to efficiently perform, and in standardized conditions, the determination, the declaration and the verification of noise emission values of refuse collection vehicles.
The use of this annex ensures the reproducibility of the determination of noise emission values within the limits established for the accuracy grade of the basic standard used to determine noise emission values. The methods used to determine these noise emission values, corresponding to this normative annex, are grade 2 accuracy measurement methods.
This standard deals with the noise measurement conditions for the types of RCVs defined and described in the standards of the EN 1501 series
This European Standard applies to machines which are manufactured after the date of approval of this standard by CEN.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1501-2:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles
EN 1501-2:2021

This document applies to side loaded refuse collection vehicle (RCV), as defined in prEN 1501-1.
This document deals with all significant hazards, hazardous situations and events relevant to the side loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the side loaded RCV so as to ensure that it is fit for its intended function and can be operated, moved, cleaned (including unblocking), adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the side loaded RCV.
This document describes and defines the safety requirements of side loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Safety requirements for the lifting device(s) including the loader cranes and the interface to the RCV are defined in prEN 1501-5.
Safety requirements for loader cranes are defined in EN 12999.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
-   below −25 °C and above +40 °C temperatures;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1501-3:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles
EN 1501-3:2021

This document applies to front loaded refuse collection vehicle (RCV), as defined in 3.2 with closed system defined in 3.13.
This document deals with all significant hazards, hazardous situations and events relevant to the front loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the front loaded RCV so as to ensure that it is fitted for its function and can be operated adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the front loaded RCV.
prEN 1501-3 describes and defines the safety requirements of front loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Safety requirements for the lifting device(s), loader cranes and their interface to the RCV are defined in prEN 1501-5.
Safety requirements for loader cranes are defined in EN 12999. Additional requirements to loader cranes installed as a loading device for handling containers for refuse or recyclable material on RCVs are defined in prEN 1501 5.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
-   operation in severe conditions e.g. extreme environmental conditions such as:
-   below −25 °C and above +40 °C temperatures;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1501-1:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
EN 1501-1:2021

This document applies to rear loaded refuse collection vehicles (RCV), as defined in 3.2.
This document deals with all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the rear loaded RCV so as to ensure that it is fit for its function and can be operated, adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the rear loaded RCV.
This document describes and defines the safety requirements of rear loaded RCVs excluding the interface tailgate/discharge door with the lifting device(s) and the lifting device(s) as illustrated in Figure A.1.
Safety requirements for the lifting device(s) and the interface with the tailgate/discharge door are defined in prEN 1501-5. Safety requirements for loader cranes are defined in EN 12999.
This European Standard is not applicable to:
-   operation in severe conditions, e.g. extreme environmental conditions such as:
-   below -25 °C and above +40 °C temperatures;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1501-5:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles
EN 1501-5:2021

This document deals with all significant hazards, hazardous situations and events relevant to lifting devices used for the emptying of designated refuse containers into RCVs and their fitting onto the RCVs when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer throughout their foreseeable lifetime as defined in Clause 4.
This document is applicable to the design and construction of the refuse container lifting devices and the mounting of other lifting devices so as to ensure that they are fitted for their function and can be operated, adjusted and maintained during their entire lifetime. It is not applicable to the end of life of the lifting devices.
This document describes and gives the safety requirements of the lifting devices for emptying refuse containers and their interfaces with the corresponding parts of the RCVs and will be used in conjunction with prEN 1501-1 for the rear, side and front loaded RCVs. It refers to EN 1501-4 for the noise test code.
This document is not applicable to:
-   operation in severe conditions e.g. extreme environmental conditions such as:
-   temperatures below −25 °C and above +40 °C;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   lifting and transportation of persons;
-   emptying refuse containers other than those manufactured according to EN 840 (all parts), EN 12574 (all parts), EN 13071 (all parts), and those described as paladin, diamond, skip containers;
-   loading bulky refuse by means of platform or forks;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships;
-   fitting and operation on stationary compactors.
This document is not applicable to machinery which is manufactured before the date of its publication by CEN.

  • Standard
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15429-3:2015(Main)
Sweepers - Part 3: Efficiency of particulate matter collection - Testing and Evaluation
EN 15429-3:2015

This test establishes a method to assess the PM10 and PM2.5 efficiency of road sweepers. PM10 and PM2.5 efficiency includes a sweeper’s ability to:
   Remove and capture PM10 and PM2.5 particulate matter, and coarse size fractions, from typical urban road surfaces;
   Minimize the amount of airborne and entrained PM10 and PM2.5 particulate matter resulting from the sweeping process.
The sweeper’s ability to remove and capture particulate matter and coarse size fractions is assessed using procedures and equipment to determine the amount of a test material (consisting of particulate matter and coarser size fractions) the sweeper is able to remove from a test surface during a controlled test run. This test measurement is used to calculate the removal efficiency for the sweeper.
The sweeper’s ability to minimize the amount of airborne and entrained particulate matter is also assessed using procedures and equipment to determine the airborne concentrations of PM10 and PM2.5 resulting from the sweeping of a test material (consisting of particulate matter and coarser size fractions) during a controlled test run. The test measurements are used to calculate PM10 and PM2.5 emission ratings for the sweeper.
This test allows the use of dust suppression water. Sweepers configured as flushing machines, or equipped with front-mounted spray bars which are not part of a dust suppression water system are not within the scope of this test.
The road sweeper’s performance results are reported in a quantitative numerical format that will allow comparative assessments of similarly classified sweepers. This test does not specify pass/fail criteria for the PM10 and PM2.5 efficiency measurements specified in the test procedure.
This test is applicable to truck mounted, self-propelled, towed and attached sweeping equipment as defined in EN 15429-1, Section 2.
This test is a model/type test, requiring the sweeper being tested to be representative of all factory production of that particular sweeper model.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15429-4:2015(Main)
Sweepers - Part 4: Symbols for operator controls and other displays
EN 15429-4:2015

This document deals with graphical symbols uniquely used to indicate the function and status of operator controls and tell-tale displays of the specialized equipment.
Common symbols that are included in other standards and applied to a wider range of machines are not included. Typically, symbols in this category that may equally be applied to surface cleaning machines can be found in ISO 2575 and ISO 6405.
This document does not apply to machines or components that are specifically designed for cleaning tramlines and rail tracks. Industrial sweepers, within the scope of EN 60335-2-72 are excluded from this standard.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 16596:2014(Main)
Electric-electronic interface between chassis-cab and bodywork of refuse collection vehicles (RCVs)
CEN/TR 16596:2013

This Technical Report proposes a standardized interface between the chassis-cab and the bodywork of refuse collection vehicles. The solution, initially for vehicles with hard wired interface and CAN interface, is developed into full CAN communication between the bodywork and the chassis-cab.

  • Technical report
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15429-2:2013(Main)
Sweepers - Part 2: Performance requirements and test methods
EN 15429-2:2012

This European Standard applies to surface cleaning machines for outdoor applications in public areas, roads, airports and industrial complexes. Cleaning machines for winter maintenance and/or indoor applications are not included within the scope of this European Standard. Surface cleaning machines in terms of this standard, are self-propelled, truck mounted, attached sweeping equipment or pedestrian controlled. This European Standard deals with the performance and functional characteristics and the test methods applied to the sweeping equipment when used as intended and under the conditions foreseen by the manufacturer. This European Standard does not include carrier vehicles (e.g. trucks). These are covered in national or EU Directives for vehicles. This European Standard does not apply to road surface cleaning equipment that would be front mounted on tractors according to EN 13524, or other vehicles. This European Standard does not apply to machines or components that are specifically designed for cleaning tramlines and rail tracks. This European Standard does not cover noise emission or any overload protection as these are covered by regulatory requirements. Industrial sweepers, within the scope of EN 60335-2-72 are excluded from this standard.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15906:2012(Main)
Winter maintenance equipment - Snow removal machines with rotating tools - Specification and clearing capacity
EN 15906:2011

This European standard specifies requirements for snow removal machines with rotating tools for winter application on traffic areas. It is valid for design and construction. It also includes the minimum requirement concerning contents of the operating instructions.
This standard applies to:
- snow blower;
- snow cutter;
- snow cutter - blower;
and related products as side blower, side cutter, etc.
This standard does not apply for:
- requirements for registration and approval;
- vehicle manufacturer requirements;
- safety requirements.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day