SIST EN ISO 10140-1:2010/A2:2014
(Amendment)Acoustics - Laboratory measurement of sound insulation of building elements - Part 1: Application rules for specific products - Amendment 2: Rainfall sound (ISO 10140-1:2010/Amd 2:2014)
Acoustics - Laboratory measurement of sound insulation of building elements - Part 1: Application rules for specific products - Amendment 2: Rainfall sound (ISO 10140-1:2010/Amd 2:2014)
This part of ISO 10140 specifies test requirements for building elements and products, including detailed requirements for preparation, mounting, operating and test conditions, as well as applicable quantities and additional test information for reporting. The general procedures for airborne and impact sound insulation measurements are given in ISO 10140-2 and ISO 10140-3, respectively.
Akustik - Messung der Schalldämmung von Bauteilen im Prüfstand - Teil 1: Anwendungsregeln für bestimmte Produkte - Änderung 2: Regenschall (ISO 10140-1:2010/Amd 2:2014)
Dieser Teil der ISO 10140 legt Prüfanforderungen für Bauteile und Produkte, einschließlich der ausführlichen Anforderungen an die Vorbereitung, Befestigung, die Betriebs und die Prüfbedingungen sowie anwendbare Größen und zusätzlich in den Prüfbericht aufzunehmende Angaben fest. Die allgemeinen Vorgehensweisen für die Messung der Luftschall und der Trittschalldämmung sind in ISO 10140-2 bzw. ISO 10140-3 enthalten.
Acoustique - Mesurage en laboratoire de l'isolation acoustique des éléments de construction - Partie 1: Règles d'application pour produits particuliers - Amendement 2: Bruit produit par la pluie (ISO 10140-1:2010/Amd 2:2014)
Akustika - Laboratorijsko merjenje zvočne izolirnosti gradbenih elementov - 1. del: Pravila uporabe za določene izdelke - Dopolnilo 2: Hrup zaradi dežja (ISO 10140-1:2010/Amd 2:2014)
Ta del ISO 10140 določa preskusne zahteve za gradbene elemente in izdelke, vključno z podrobnimi zahtevami za pripravljalne, namestitvene, obratovalne in preskusne pogoje ter prav tako z ustreznimi količinami in dodatnimi informacijami o preskušanju za poročanje. Splošni postopki za ukrepe izolirnosti pred zvokom v zraku in udarnim zvokom so podani v ISO 10140-2 in ISO 10140-3 v tem zaporedju.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10140-1:2010/A2:2014
01-september-2014
$NXVWLND/DERUDWRULMVNRPHUMHQMH]YRþQHL]ROLUQRVWLJUDGEHQLKHOHPHQWRYGHO
3UDYLODXSRUDEH]DGRORþHQHL]GHONH'RSROQLOR +UXS]DUDGLGHåMD ,62
$PG
Acoustics - Laboratory measurement of sound insulation of building elements - Part 1:
Application rules for specific products - Amendment 2: Rainfall sound (ISO 10140-
1:2010/Amd 2:2014)
Akustik - Messung der Schalldämmung von Bauteilen im Prüfstand - Teil 1:
Anwendungsregeln für bestimmte Produkte - Änderung 2: Regenschall (ISO 10140-
1:2010/Amd 2:2014)
Acoustique - Mesurage en laboratoire de l'isolation acoustique des éléments de
construction - Partie 1: Règles d'application pour produits particuliers - Amendement 2:
Bruit produit par la pluie (ISO 10140-1:2010/Amd 2:2014)
Ta slovenski standard je istoveten z: EN ISO 10140-1:2010/A2:2014
ICS:
17.140.01 $NXVWLþQDPHUMHQMDLQ Acoustic measurements and
EODåHQMHKUXSDQDVSORãQR noise abatement in general
91.060.01 Stavbni elementi na splošno Elements of buildings in
general
91.120.20 $NXVWLNDYVWDYEDK=YRþQD Acoustics in building. Sound
L]RODFLMD insulation
SIST EN ISO 10140-1:2010/A2:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
EUROPEAN STANDARD
EN ISO 10140-1:2010/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2014
ICS 91.120.20
English Version
Acoustics - Laboratory measurement of sound insulation of
building elements - Part 1: Application rules for specific products
- Amendment 2: Rainfall sound (ISO 10140-1:2010/Amd 2:2014)
Acoustique - Mesurage en laboratoire de l'isolation Akustik - Messung der Schalldämmung von Bauteilen im
acoustique des éléments de construction - Partie 1: Règles Prüfstand - Teil 1: Anwendungsregeln für bestimmte
d'application pour produits particuliers - Amendement 2: Produkte - Änderung 2: Regenschall (ISO 10140-
Bruit produit par la pluie (ISO 10140-1:2010/Amd 2:2014) 1:2010/Amd 2:2014)
This amendment A2 modifies the European Standard EN ISO 10140-1:2010; it was approved by CEN on 20 March 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10140-1:2010/A2:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
EN ISO 10140-1:2010/A2:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
EN ISO 10140-1:2010/A2:2014 (E)
Foreword
This document (EN ISO 10140-1:2010/A2:2014) has been prepared by Technical Committee ISO/TC 43
"Acoustics" in collaboration with the Technical Committee CEN/TC 126 “Acoustic properties of building
elements and of buildings” the secretariat of which is held by AFNOR.
This Amendment to the European Standard EN ISO 10140-1:2010 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by November 2014, and
conflicting national standards shall be withdrawn at the latest by November 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of EN ISO 10140-1:2010/Amd 2:2014 has been approved by CEN as EN ISO 10140-1:2010/A2:2014
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
INTERNATIONAL ISO
STANDARD 10140-1
First edition
2010-09-01
AMENDMENT 1
2012-02-01
Acoustics — Laboratory measurement of
sound insulation of building elements —
Part 1:
Application rules for specific products
AMENDMENT 1: Guidelines for the
determination of the sound reduction index
of joints filled with fillers and/or seals
Acoustique — Mesurage en laboratoire de l'isolation acoustique des
éléments de construction —
Partie 1: Règles d'application pour produits particuliers
AMENDEMENT 1: Lignes directrices pour la détermination de l'indice
de réduction acoustique de joints comblés de matière de remplissage
et/ou d'éléments d'étanchéité
Reference number
ISO 10140-1:2010/Amd.1:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
ISO 10140-1:2010/Amd.1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
ISO 10140-1:2010/Amd.1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 10140-1:2010 was prepared by Technical Committee ISO/TC 43, Acoustics,
Subcommittee SC 2, Building acoustics.
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
---------------------- Page: 10 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
ISO 10140-1:2010/Amd.1:2012(E)
Acoustics — Laboratory measurement of sound insulation of
building elements —
Part 1:
Application rules for specific products
AMENDMENT 1: Guidelines for the determination of the sound
reduction index of joints filled with fillers and/or seals
page v, Introduction
Add the following final paragraph.
Annex J has been developed for joints filled with fillers or seals.
page 1, Clause 2
Add the date “2010” to ISO 10140-2.
page 31
Insert Annex J, which starts on page 2, before the Bibliography.
page 32, Bibliography
Add the following entries.
[15] EN 12354-3, Building acoustics — Estimation of acoustic performance of buildings from the
performance of elements — Part 3: Airborne sound insulation against outdoor sound
[16] NEN 5273, Akoestische prestatie van kier- en naaddichting — Laboratoriummeetmethode op
basis van NEN-EN-ISO 140-3 [Acoustic performance of sealing — Laboratory measurement
based on EN ISO 140-3]
[17] ERTEL, H., MECHEL, F.P. Akustische Dichtung von Fugen durch akustisch wirksame
Nebenvolumen -akustiche Filter- und akustische Lippendichtungen. [Acoustic sealing of joints
by acoustically effective supplementary volumes — Acoustic filter and acoustic lip seals].
Stuttgart: Fraunhofer IRB, 1979. 37 p. (IBP Report No. BS 35/79.)
[18] ERTEL, H. Experimentelle Untersuchungen von akustischen Fugendichtungen —
Prinziplösungen für wirksame Dichtungskonstruktionen [Experimental investigations of acoustic
joint seals — Principle of solutions for effective seal construction]. Stuttgart: Fraunhofer IRB,
1981. 44 p. (IBP Report No. BS 57/81.)
[19] FROELICH, H., SCHUMACHER, R., SAß, B. Konstruktionsmerkmale für schalldämmende
Wohnungseingangstüren und Bürotüren aus Holz und Holzwerkstoffen — Forschungsbericht.
[Design features of sound-absorbing residential entrance doors and office doors in wood and
timber materials — Research report]. Stuttgart: Fraunhofer IRB, 1996. 175 p.
© ISO 2012 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 10140-1:2010/A2:2014
ISO 10140-1:2010/Amd.1:2012(E)
Annex J
(normative)
Joints filled with fillers or seals — Sound reduction index
J.1 Application
This annex applies to acoustic sealing of slits (with or without fillers) and of gaps or joints between parts of
windows or doors. Fillers are materials to fill in joints, e.g. foam or sealing tape, gaskets (or seals) are
elements to close openable joints, e.g. retractable floor seals or rebate seals for doors and windows.
The general guidelines in the relevant clauses of ISO 10140-2 shall always be followed. The quantity to be
determined is the sound reduction index of joints, R , per metre of a sealed gap or joint, in decibels as a
s
function of frequency.
The sound reduction index of joints (of the slit, s) with sound transmission only through the joint or the slit is
evaluated from Equation (J.1).
Sl
n
RLL10 lg (J.1)
s1 2
A l
n
where
L is the energy average sound pressure level in the source room, in decibels (see ISO 10140-2);
1
L is the energy average sound pressure level in the receiving room, in decibels (see ISO 10140-2);
2
l is the length of the joint, in metres;
2
is the reference area, in square metres (S = 1 m );
S
n n
l is the reference length, in metres (l = 1 m);
n n
A is the equivalent absorption area in the receiving room, in square metres.
NOTE To achieve a better signal-to-noise ratio, simultaneous measurements can be performed on an element with
enlarged length of the joint.
For this type of measurement, the influence of flanking transmission through the object in which the slits are
present can be very important, so the maximum sound insulation of the test arrangement requires
measurement, e.g. by sealing the test joint on both sides with elastic sealant, leading to R . Unless this
s,max
value is 10 dB higher than the measured value, the measu
...
SLOVENSKI STANDARD
SIST EN ISO 10140-1:2010/oprA2:2013
01-februar-2013
$NXVWLND/DERUDWRULMVNRPHUMHQMH]YRþQHL]ROLUQRVWLJUDGEHQLKHOHPHQWRYGHO
3UDYLODXSRUDEH]DGRORþHQHL]GHONH+UXS]DUDGLGHåMD ,62 '$0
Acoustics - Laboratory measurement of sound insulation of building elements - Part 1:
Application rules for specific products - Rainfall noise (ISO 10140-1:2010/DAM 2:2012)
Akustik - Messung der Schalldämmung von Bauteilen im Prüfstand - Teil 1:
Anwendungsregeln für bestimmte Produkte - Regenschall (ISO 10140-1:2010/DAM
2:2012)
Acoustique - Mesurage en laboratoire de l'isolation acoustique des éléments de
construction - Partie 1: Règles d'application pour produits particuliers - Bruit produit par
la pluie (ISO 10140-1:2010/DAM 2:2012)
Ta slovenski standard je istoveten z: EN ISO 10140-1:2010/prA2
ICS:
17.140.01 $NXVWLþQDPHUMHQMDLQ Acoustic measurements and
EODåHQMHKUXSDQDVSORãQR noise abatement in general
91.060.01 Stavbni elementi na splošno Elements of buildings in
general
91.120.20 $NXVWLNDYVWDYEDK=YRþQD Acoustics in building. Sound
L]RODFLMD insulation
SIST EN ISO 10140-1:2010/oprA2:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
EUROPEAN STANDARD
DRAFT
EN ISO 10140-1:2010
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
November 2012
ICS 91.120.20
English Version
Acoustics - Laboratory measurement of sound insulation of
building elements - Part 1: Application rules for specific products
- Rainfall noise (ISO 10140-1:2010/DAM 2:2012)
Acoustique - Mesurage en laboratoire de l'isolation Akustik - Messung der Schalldämmung von Bauteilen im
acoustique des éléments de construction - Partie 1: Règles
Prüfstand - Teil 1: Anwendungsregeln für bestimmte
d'application pour produits particuliers - Bruit produit par la Produkte - Regenschall (ISO 10140-1:2010/DAM 2:2012)
pluie (ISO 10140-1:2010/DAM 2:2012)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 126.
This draft amendment A2, if approved, will modify the European Standard EN ISO 10140-1:2010. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10140-1:2010/prA2:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
EN ISO 10140-1:2010/prA2:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
EN ISO 10140-1:2010/prA2:2012 (E)
Foreword
This document (EN ISO 10140-1:2010/prA2:2012) has been prepared by Technical Committee ISO/TC 43
"Acoustics" in collaboration with the Technical Committee CEN/TC 126 “Acoustic properties of building
elements and of buildings” the secretariat of which is held by AFNOR.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 10140-1:2010/DAM 2:2012 has been approved by CEN as a EN ISO 10140-1:2010/prA2:2012
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
DRAFT AMENDMENT ISO 10140-1:2010/DAM 2
ISO/TC 43/SC 2 Secretariat: DIN
Voting begins on Voting terminates on
2012-11-07 2013-04-07
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Acoustics — Laboratory measurement of sound insulation of
building elements —
Part 1:
Application rules for specific products
AMENDMENT 2: Rainfall noise
Acoustique — Mesurage en laboratoire de l'isolation acoustique des éléments de construction —
Partie 1: Règles d'application pour produits particuliers
AMENDEMENT 2: Bruit produit par la pluie
ICS 91.120.20
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
ISO 10140-1:2010/DAM 2
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
ISO 10140-1:2010/DAM 2
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 2 to ISO 10140-1:2010 was prepared by Technical Committee ISO/TC 43, Acoustics,
Subcommittee SC 2, Building acoustics.
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
---------------------- Page: 10 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
DRAFT AMENDMENT ISO 10140-1:2010/DAM 2
Acoustics — Laboratory measurement of sound insulation of
building elements —
Part 1:
Application rules for specific products
AMENDMENT 2: Rainfall noise
page v, Introduction
Add the following third paragraph.
Annex K has been developed for the measurement of rainfall sound.
page 31
Insert Annex K, which starts on page 2, before the Bibliography.
page 32, Bibliography
Remove the following entry.
[6] ISO 140-18, Acoustics — Measurement of sound insulation in buildings and of building elements —
Part 18: Laboratory measurement of sound generated by rainfall on building elements
Add the following entries.
[20] MCLOUGHLIN, J. SAUNDERS D.J. and FORD, R.D. Noise generated by simulated rainfall on profiled steel
roof structures, Applied Acoustics, 42 (1994), 239-255
[21] SUGA H. and TACHIBANA, H. Sound radiation characteristics of lightweight roof constructions excited by
rain, Building Acoustics, 1, No. 4 (1994), 249-255
[22] ISO 15186-1:2000, Acoustics — Measurement of sound insulation in buildings and of building
elements using sound intensity — Part 1: Laboratory measurements
[23] IEC 60721-2-2, Classification of environmental conditions – Part 2: Environmental conditions
appearring in nature – Precipitation and wind.
© ISO 2012 – All rights reserved
1
---------------------- Page: 11 ----------------------
SIST EN ISO 10140-1:2010/oprA2:2013
ISO 10140-1:2010/DAM 2
Annex K
(normative)
Roofs, roof/ceiling systems and skylights - Rainfall sound
K.1 Application
This annex applies to the impact sound insulation of roofs, roof/ceiling systems and skylights e
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.