Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and ferritic-austenitic stainless steels

This Part of this European Standard specifies the technical delivery conditions for forgings for pressure purposes made of stainless steels, including creep resisting steels. Chemical composition and mechanical properties are specified. General information on technical delivery conditions is given in EN 10021.

Schmiedestücke aus Stahl für Druckbehälter - Teil 5: Martensitische, austenitische und ferritisch-austenitische nichtrostende Stähle

Diese Europäische Norm legt die Anforderungen an Schmiedestücke aus nicht rostenden und aus hochwarmfesten Stählen, fest. Die chemische Zusammensetzung und mechanische Eigenschaften sind festgelegt.
Bei Lieferungen nach dieser Europäischen Norm gelten ebenfalls die allgemeinen technischen Lieferbedingungen nach EN 10021.

Pièces forgées en acier pour appareils à pression - Partie 5: Aciers inoxydables austénitiques martensitiques et austénoferritiques

La présente partie de la norme européenne spécifie les conditions techniques de livraison des pièces forgées en aciers ferritiques et martensitiques, avec caractéristiques spécifiées à température élevée, pour appareils à pression.
Les informations générales sur les conditions techniques de livraison sont données dans l'EN 10021.

Jekleni izkovki za tlačne posode - 5. del: Martenzitna, avstenitna in avstenitno-feritna nerjavna jekla

Ta del tega evropskega standarda določa tehnične dobavne pogoje za izkovke za tlačne posode iz nerjavnih jekel, vključno z jekli, ki so odporna proti lezenju. Določene so kemijska sestava in mehanske lastnosti. Splošne informacije o tehničnih dobavnih pogojih so podane v standardu EN 10021.

General Information

Status
Published
Publication Date
25-Apr-2017
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
20-Apr-2017
Due Date
25-Jun-2017
Completion Date
26-Apr-2017

Relations

Buy Standard

Standard
EN 10222-5:2017
English language
29 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Schmiedestücke aus Stahl für Druckbehälter - Teil 5: Martensitische, austenitische und ferritisch-austenitische nichtrostende StählePièces forgées en acier pour appareils à pression - Partie 5: Aciers inoxydables austénitiques martensitiques et austénoferritiquesSteel forgings for pressure purposes - Part 5: Martensitic, austenitic and ferritic-austenitic stainless steels77.140.85Železni in jekleni kovani izdelkiIron and steel forgings77.140.30Jekla za uporabo pod tlakomSteels for pressure purposesICS:Ta slovenski standard je istoveten z:EN 10222-5:2017SIST EN 10222-5:2017en,fr,de01-junij-2017SIST EN 10222-5:2017SLOVENSKI
STANDARDSIST EN 10222-5:2000/AC:2004SIST EN 10222-5:20001DGRPHãþD



SIST EN 10222-5:2017



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10222-5
April
t r s y ICS
y yä s v rä u râ
y yä s v rä z w Supersedes EN
s r t t tæ wã s { { {English Version
Steel forgings for pressure purposes æ Part
wã Martensiticá austenitic and austeniticæferritic stainless steels Pièces forgées en acier pour appareils à pression æ Partie
wã Aciers inoxydables austénitiques martensitiques et austénoferritiques
Schmiedestücke aus Stahl für Druckbehälter æ Teil
wã Martensitischeá austenitische und austenitischeæferritisch nichtrostende Stähle This European Standard was approved by CEN on
t w December
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r t t tæ wã t r s y ESIST EN 10222-5:2017



EN 10222-5:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Classification and designation . 4 4.1 Classification . 4 4.2 Designation. 4 5 Information to be supplied by the purchaser . 5 5.1 Mandatory information . 5 5.2 Options . 5 6 Requirements . 5 6.1 Steelmaking process and manufacture of the product . 5 6.2 Delivery condition . 5 6.3 Chemical composition and chemical corrosion properties . 5 6.3.1 Cast analysis . 5 6.3.2 Product analysis . 5 6.3.3 Resistance to intergranular corrosion . 5 6.4 Mechanical properties . 6 6.5 Surface condition . 6 6.6 Internal soundness . 6 6.7 Physical properties . 6 6.8 Post weld heat treatment . 6 7 Inspection . 6 8 Sampling . 6 9 Test methods . 6 10 Retests . 6 11 Marking . 6 Annex A (informative)
Reference data for creep rupture strength . 20 Annex B (informative)
Post weld heat treatment . 25 Annex C (informative)
Significant technical changes to the version EN 10222-5:1999 . 27 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 2014/68/EU . 28 Bibliography . 29
SIST EN 10222-5:2017



EN 10222-5:2017 (E) 3 European foreword This document (EN 10222-5:2017) has been prepared by Technical Committee ECISS/TC 111 “Steel castings and forgings”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2017, and conflicting national standards shall be withdrawn at the latest by October 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10222-5:1999. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 2014/68/EU. For relationship with EU Directive 2014/68/EU, see informative Annex ZA, which is an integral part of this document. EN 10222 consists of the following parts under the general title “Steel forgings for pressure purposes”:
— Part 1: General requirements for open die forgings — Part 2: Ferritic and martensitic steels with specified elevated temperature properties — Part 3: Nickel steels with specified low temperature properties — Part 4: Weldable fine grain steels with high proof strength — Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels. Annex C provides details about significant technical changes to EN 10222-5:1999. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 10222-5:2017



EN 10222-5:2017 (E) 4 1 Scope This European Standard specifies the technical delivery conditions for forgings for pressure purposes, made of stainless steels, including creep resisting steels. Chemical composition and mechanical properties are specified. NOTE Once this standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done. The series EN 10222–1 to EN 102225 is structured so that the data related to different materials is in the part allocated for that material. The presumption of conformity to the Essential Safety Requirements of Directive 2014/68/EU depends on both the text in part 1 and the data in part 2, 3, 4 or 5. General information on technical delivery conditions is given in EN 10021. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10088-1:2014, Stainless steels - Part 1: List of stainless steels EN 10222-1:2017, Steel forgings for pressure purposes — Part 1: General requirements for open die forgings EN ISO 3651-2:1998, Determination of resistance to intergranular corrosion of stainless steels - Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in media containing sulfuric acid (ISO 3651-2:1998) 3 Terms and definitions For the purpose of this document, the terms and definitions given in EN 10222-1:2017 apply. 4 Classification and designation 4.1 Classification The steel grades covered in this document are classified according to their structure into: — martensitic steels; — austenitic steels; — austenitic-ferritic steels. NOTE For more details see EN 10088–1. 4.2 Designation See EN 10222-1:2017. SIST EN 10222-5:2017



EN 10222-5:2017 (E) 5 5 Information to be supplied by the purchaser 5.1 Mandatory information Shall be in accordance with EN 10222-1. 5.2 Options A number of options are specified in this European Standard and listed below. Additionally the relevant options of EN 10222-1 apply. If the purchaser does not give any information to implement any of these options at the time of enquiry and order, the products shall be supplied in accordance with the basic specification (see also EN 10222-1). 1) test temperature for the tensile test at elevated temperature, if applicable (see 6.4.3); 2) test temperature of the impact test at low temperature (see 6.4.4); 3) controlled sulphur content (see Table 2, footnote b). 6 Requirements 6.1 Steelmaking process and manufacture of the product Shall be in accordance with EN 10222-1. 6.2 Delivery condition The products shall be delivered in the heat treatment condition specified in Table 1. 6.3 Chemical composition and chemical corrosion properties 6.3.1 Cast analysis The chemical composition (cast analysis), determined in accordance with EN 10222-1 shall conform to the requirements of Table 2. 6.3.2 Product analysis The product analysis shall not deviate from the specified cast analysis (see 6.3.1) by more than the values specified in Table 3. 6.3.3 Resistance to intergranular corrosion The specifications in Table 4 apply in respect to resistance to intergranular corrosion as defined in EN ISO 3651-2, for austenitic and austenitic-ferritic steels. See EN 10222-1:2017, 9.9, Table 1. NOTE 1 EN ISO 3651-2 is not applicable for testing martensitic steels. NOTE 2 The corrosion resistance of stainless steels is very dependent on the type of environment and can therefore not always be clearly as certained through laboratory tests. It is therefore advisable to draw on the available experience of the use of the steels. SIST EN 10222-5:2017



EN 10222-5:2017 (E) 6 6.4 Mechanical properties 6.4.1 When heat treated in accordance with Table 1, the mechanical properties shall conform to the requirements of Table 4. 6.4.2 Elevated temperature proof strength (Rp0,2 and Rp1,0) values shall conform to the requirements of Table 5 and Table 6. Elevated temperature tensile strength (Rm) values shall conform to Table 7. 6.4.3 If verification of specified proof strength at elevated temperature is requested (see
EN 10222-1:2017, Table 1), the testing temperature should be agreed at the time of enquiry and order. Otherwise, the test shall be carried out at 300 °C, except for the austenitic-ferritic steels, where the test shall be carried out at 250 °C. 6.4.4 The impact test, if applicable (see EN 10222-1:2017, Table 1), shall be carried out at 20 °C. Where impact tests at low temperature have been agreed (see EN 10222-1:2017, Table 1), the test temperature shall also be agreed at the time of enquiry and order. 6.4.5 Reference data for 1 % (plastic) creep strain and creep rupture are given in Annex A. 6.5 Surface condition See EN 10222-1. 6.6 Internal soundness See EN 10222-1. 6.7 Physical properties For reference data on physical properties, see EN 10088-1:2014, Annex E. 6.8 Post weld heat treatment Guidelines for the purchaser on post weld heat treatment are given in Annex B. 7 Inspection See EN 10222-1. 8 Sampling See EN 10222-1. 9 Test methods See EN 10222-1. 10 Retests See EN 10222-1. 11 Marking See EN 10222-1. SIST EN 10222-5:2017



EN 10222-5:2017 (E) 7 Table 1 — Heat treatment Steel grade Heat treatmenta Solution annealing ° C Cooling inb Steel name Steel number Martensitic steel X3CrNiMo13–4 1.4313 +QT or +T 950 to 1 050 (for quenching) a, oc
+QT a, od Austenitic steelse X2CrNi18–9 1.4307 +AT 1 025 to 1 100 w, a X2CrNi19–11 1.4306 +AT 1 000 to 1 100 w, a X2CrNiN18–10 1.4311 +AT 1 000 to 1 100 w, a X5CrNi18–10 1.4301 +AT 1 000 to 1 100 w, a X6CrNiTi18–10 1.4541 +AT 1 020 to 1 120 w, a X6CrNiNb18–10 1.4550 +AT 1 020 to 1 120 w, a X6CrNi18–10 1.4948 +AT 1 050 to 1 120 w, a X6CrNiTiB18–10 1.4941 +AT 1 070 to 1 140 w, a X7 CrNiNb18–10 1.4912 +AT 1 070 to 1 125 w, a X2CrNiMo17–12–2 1.4404 +AT 1 020 to 1 120 w, a X2CrNiMoN 17–11–2 1.4406 +AT 1 020 to 1 120 w, a X5CrNiMo17–12–2 1.4401 +AT 1 020 to 1 120 w, a X6CrNiMoTi 17–12–2 1.4571 +AT 1 020 to 1 120 w, a X2 CrNiMo17–12–3 1.4432 +AT 1 020 to 1 120 w, a X2CrNiMoN 17–13–3 1.4429 +AT 1 020 to 1 120 w, a X3CrNiMo17–13–3 1.4436 +AT 1 020 to 1 120 w, a X2CrNiMo18–14–3 1.4435 +AT 1 020 to 1 120 w, a X3CrNiMoN17–13–3 1.4910 +AT 1 020 to 1 100 w, a X2CrNiMoN17–13–5 1.4439 +AT 1 060 to 1 120 w, a X1NiCrMoCu25–20–5 1.4539 +AT 1 060 to 1 120 w, a X1CrNiMoCuN20–18–7 1.4547 +AT 1 020 to 1 120 w, a X1CrNiMoCuN25–20–7 1.4529 +AT 1 020 to 1 100 w, a X2CrNiCu19–10 1.4650 +AT 1 050 to 1 125 w, a X3CrNiMo18–12–3 1.4449 +AT 1 050 to 1 125 w, a SIST EN 10222-5:2017



EN 10222-5:2017 (E) 8 Steel grade Heat treatmenta Solution annealing ° C Cooling inb Steel name Steel number Austenitic-ferritic steelse X2CrNiN23–4 1.4362 +AT 950 to 1 100 w, a X2CrNiMoN22–5–3 1.4462 +AT 1 020 to 1 100 – X2CrNiMoCuN25–6–3 1.4507 +AT 1 040 to 1 120 w, a X2CrNiMoN25–7–4 1.4410 +AT 1 040 to 1 120 w, a X2CrNiMoCuWN25–7–4 1.4501 +AT 1 040 to 1 120 w, a a +AT solution annealed, +T tempered, +QT quenched and tempered. b a = air ; o = oil ; w = water or water based medium. c Double tempered at 600 °C to 620 °C. d Tempered at 570 °C to 600 °C. e The solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained and provided these requirements are met even after appropriate subsequent solution annealing. SIST EN 10222-5:2017



EN 10222-5:2017 (E) 9 Table 2 — Chemical composition (cast analysis)a Steel grade % by mass Steel name Steel number C Si max. Mn max. P max. S max. Cr Mo Ni N Others Martensitic steels X3CrNiMo13–4 1.4313
0,05 0,70 1,50 0,040 0,015 12,0 to 14,0 0,30 to 0,70 3,5 to 4,5
0,020 – Austenitic steels X2CrNi18–9 1.4307
0,030 1,00 2,00 0,045 0,015b 17,5 to 19,5 – 8,0 to 10,5
0,10 – X2CrNi19–11 1.4306
0,030 1,00 2,00 0,045 0,015b 18,0 to 20,0 – 10,0 to 12,0
0,10 – X2CrNiN18–10 1.4311
0,030 1,00 2,00 0,045 0,015b 17,5 to 19,5 – 8,5 to 11,5 0,12 to 0,22 – X5CrNi18–10 1.4301
0,07 1,00 2,00 0,045 0,015b 17,5 to 19,5 – 8,0 to 10,5
0,10 – X6CrNiTi18–10 1.4541
0,08 1,00 2,00 0,045 0,015b 17,0 to 19,0 – 9,0 to 12,0 – Ti:5 x C to 0,70 X6CrNiNb18–10 1.4550
0,08 1,00 2,00 0,045 0,015b 17,0 to 19,0 – 9,0 to 12,0 – Nb:10 x C to 1,00 X6CrNi18–10 1.4948 0,04 to 0,08 1,00 2,00 0,035 0,015b 17,0 to 19,0 – 8,0 to 11,0
0,10 – X6CrNiTiB18–10 1.4941 0,04 to 0,08 1,00 2,00 0,035 0,015b 17,0 to 19,0 – 9,0 to 12,0 – Ti: 5 x C to 0,80
B:0,0015 to 0,0050 X7CrNiNb18–10 1.4912 0,04 to 0,10 1,00 2,00 0,045 0,015b 17,0 to 19,0 – 9,0 to 12,0 – Nb:10 x C to 1,20 X2CrNiMo17–12–2 1.4404
0,030 1,00 2,00 0,045 0,015b 16,5 to 18,5 2,00 to 2,50 10,0 to 13,0
0,10 – X2CrNiMoN17–11–2 1.4406
0,030 1,00 2,00 0,045 0,015b 16,5 to 18,5 2,00 to 2,50 10,0 to 12,5 0,12 to 0,22 – SIST EN 10222-5:2017



EN 10222-5:2017 (E) 10 Steel grade % by mass Steel name Steel number C Si max. Mn max. P max. S max. Cr Mo Ni N Others X5CrNiMo17–12–2 1.4401
0,07 1,00 2,00 0,045 0,015b 16,5 to 18,5 2,00 to 2,50 10,0 to 13,0
0,10 – X6CrNiMoTi17–12–2 1.4571
0,08 1,00 2,00 0,045 0,015b 16,5 to 18,5 2,00 to 2,50 10,5 to 13,5 – Ti:5 x C to 0,70 X2CrNiMo17–12–3 1.4432
0,030 1,00 2,00 0,045 0,015b 16,5 to 18,5 2,50 to 3,00 10,5 to 13,0
0,10 – X2CrNiMoN17–13–3 1.4429
0,030 1,00 2,00 0,045 0,015b 16,5 to 18,5 2,50 to 3,00 11,0 to 14,0 0,12 to 0,22 – X3CrNiMo17–13–3 1.4436
0,05 1,00 2,00 0,045 0,015b 16,5 to 18,5 2,50 to 3,00 10,5 to 13,0
0,10 – X2CrNiMo18–14–3 1.4435
0,030 1,00 2,00 0,045 0,015b 17,0 to 19,0 2,50 to 3,00 12,5 to 15,0
0,10 – X3CrNiMoBN17–13–3 1.4910
0,04 0,75 2,00 0,035 0,015 16,0 to 18,0 2,00 to 3,00 12,0 to 14,0 0,10 to 0,18 B:0,0015 to 0,0050 X2CrNiMoN17–13–5 1.4439
0,030 1,00 2,00 0,045 0,015 16,5 to 18,5 4,00 to 5,00 12,5 to 14,5 0,12 to 0,22 – X1NiCrMoCu25–20–5 1.4539
0,020 0,70 2,00 0,030 0,010 19,0 to 21,0 4,00 to 5,00 24,0 to 26,0
0,15 Cu: 1,20 to 2,00 X1CrNiMoCuN20–18–7 1.4547
0,020 0,70 1,00 0,030 0,010 19,5 to 20,5 6,00 to 7,00 17,5 to 18,5 0,18 to 0,25 Cu: 0,50 to 1,00 X1CrNiMoCuN25–20–7 1.4529
0,020 0,50 1,00 0,030 0,010 19,0 to 21,0 6,00 to 7,00 24,0 to 26,0 0,15 to 0,25 Cu: 0,50 to 1,50 X2CrNiCu19–10 1.4650
0,030 1,00 2,00 0,045 0,015 18,5 to 20,0 – 9,0 to 10,0
0,08 Cu
1,0 X3CrNiMo18–12–3 1.4449
0,035 1,00 2,00 0,045 0,015 17,0 to 18,2 2,25 to 2,75 11,5 to 12,5
0,08 Cu
1,0 SIST EN 10222-5:2017



EN 10222-5:2017 (E) 11 Steel grade % by mass Steel name Steel number C Si max. Mn max. P max. S max. Cr Mo Ni N Others Austenitic-ferritic steels X2CrNiN23–4 1.4362
0,030 1,00 2,00 0,035 0,015 22,0 to 24,0 0,10 to 0,60 3,5 to 5,5 0,05 to 0,20 Cu: 0,10 to 0,60 X2CrNiMoN22–5–3 1.4462
0,030 1,00 2,00 0,035 0,015 21,0 to 23,0 2,50 to 3,5 4,5 to 6,5 0,10 to 0,22 – X2CrNiMoCuN25–6–3 1.4507
0,030 0,70 2,00 0,035 0,015 24,0 to 26,0 3,00 to 4,0 6,0 to 8,0 0,20 to 0,30 Cu: 1,00 to 2,50 X2CrNiMoN25–7–4 1.4410
0,030 1,00 2,00 0,035 0,015 24,0 to 26,0 3,00 to 4,5 6,0 to 8,0 0,24 to 0,35 – X2CrNiMoCuWN25–7–4 1.4501
0,030 1,00 1,00 0,035 0,015 24,0 to 26,0 3,00 to 4,0 6,0 to 8,0 0,20 to 0,30 W: 0,50 to 1,00
Cu: 0,50 to1,00 a Elements not listed in this table may not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All appropriate precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would im
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.