SIST EN ISO 14310:2004
(Main)Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs (ISO 14310:2001)
Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs (ISO 14310:2001)
Erdöl- und Erdgasindustrie - Bohrloch-Ausrüstung - Packer und Brückenstopfen (ISO 14310:2001)
Diese Internationale Norm legt Anforderungen an Packer und Brückenstopfen für den Einsatz in der Erdöl- und Erdgasindustrie fest. Die Anwendung dieser Internationalen Norm ist begrenzt auf diejenigen Produkte, die die Definition eines Packers oder Brückenstopfens für Untertagearbeiten in der Erdöl- und Erdgasindustrie erfüllen.
Diese Internationale Norm gilt nur für Produktanwendungen innerhalb eines Rohres. Die Installation und Instandhaltung dieser Produkte liegen außerhalb des Anwendungsbereiches dieser Internationalen Norm.
Industries du pétrole et du gaz naturel - Equipement de fond de trou - Garnitures d'étanchéité (packers) et bouchons mécaniques d'isolation de fond (ISO 14310:2001)
Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs (ISO 14310:2001)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2004
Petroleum and natural gas industries - Downhole equipment - Packers and bridge
plugs (ISO 14310:2001)
Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs
(ISO 14310:2001)
Erdöl- und Erdgasindustrie - Bohrloch-Ausrüstung - Packer und Brückenstopfen (ISO
14310:2001)
Industries du pétrole et du gaz naturel - Equipement de fond de trou - Garnitures
d'étanchéité (packers) et bouchons mécaniques d'isolation de fond (ISO 14310:2001)
Ta slovenski standard je istoveten z: EN ISO 14310:2001
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 14310
First edition
2001-12-01
Petroleum and natural gas industries —
Downhole equipment — Packers and
bridge plugs
Industries du pétrole et du gaz naturel — Équipement de fond de trou —
Garnitures d'étanchéité (packers) et bouchons mécaniques d'isolation de
fond
Reference number
ISO 14310:2001(E)
©
ISO 2001
ISO 14310:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved
ISO 14310:2001(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 Normative references.1
3 Terms and definitions .1
4 Abbreviated terms .5
5 Functional specification.5
5.1 General.5
5.2 Functional characteristics .5
5.3 Well parameters .5
5.4 Operational parameters .6
5.5 Environmental compatibility .6
5.6 Well equipment compatibility.6
5.7 Quality control .7
5.8 Design validation .7
6 Technical specification .7
6.1 General.7
6.2 Technical characteristics.7
6.3 Design criteria.7
6.4 Design verification.9
6.5 Design validation .10
6.6 Design changes .14
6.7 Functional test parameters.15
6.8 Other validations .15
7 Supplier/manufacturer requirements .15
7.1 Data control.15
7.2 Documentation requirements.15
7.3 Product identification.16
7.4 Quality control .17
7.5 Functional test .21
8 Repair.21
Annex A (normative) Special validation grade with acceptance criterion of zero bubbles (V0) .22
Bibliography.23
ISO 14310:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14310 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for
petroleum and natural gas industries, Subcommittee SC 4, Drilling and production equipment.
Annex A forms a normative part of this International Standard.
iv © ISO 2001 – All rights reserved
ISO 14310:2001(E)
Introduction
This International Standard has been developed by users/purchasers and suppliers/manufacturers of packers and
bridge plugs intended for use in the petroleum and natural gas industry worldwide. This International Standard is
intended to give requirements and information to both parties in the selection, manufacture, testing and use of
packers and bridge plugs. Further, this International Standard addresses supplier/manufacturer requirements which
set the minimum parameters with which suppliers/manufacturers shall comply to claim conformity with this
International Standard.
This International Standard has been structured with grades of increased requirements both in quality control and
design validation. These variations allow the user/purchaser to select the grade required for a specific application.
The three quality control grades provide the user/purchaser the choice of requirements to meet a specific
preference or application. Quality control grade Q3 is the minimum grade of quality offered by this product
standard. Quality control grade Q2 provides additional inspection and verification steps, and quality control grade
Q1 is the highest grade provided. Additional quality upgrades can be specified by the user/purchaser as
supplemental requirements.
Six standard design validation grades (V1 to V6) and one special design validation grade (V0) provide the
user/purchaser the choice of requirements to meet a specific preference or application. Design validation grade V6
is the minimum grade and represents equipment where the validation method has been defined by the
supplier/manufacturer. The complexity and severity of the validation testing increases as the grade number
decreases.
Design validation grade V6 and quality control grade Q3 represent equipment designed and manufactured
consistent with minimum industry practice. These grades are sufficient for a number of applications; however, some
applications could require and justify the higher grades of quality control and design validation defined by this
International Standard.
Users of this International Standard should be aware that requirements above those outlined in this International
Standard may be needed for individual applications. This International Standard is not intended to inhibit a
supplier/manufacturer from offering, or the user/purchaser from accepting, alternative equipment or engineering
solutions. This may be particularly applicable where there is innovative or developing technology. Where an
alternative is offered, the supplier/manufacturer should identify any variations from this International Standard and
provide details.
INTERNATIONAL STANDARD ISO 14310:2001(E)
Petroleum and natural gas industries — Downhole equipment —
Packers and bridge plugs
1 Scope
This International Standard provides requirements for packers and bridge plugs for use in the petroleum and
natural gas industry. Application of this International Standard is limited to those products meeting the definition of
a packer or bridge plug intended for petroleum and natural gas industry subsurface operations.
This International Standard applies only to product applications within a conduit. Installation and maintenance of
these products is outside the scope of this International Standard.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 2859-1:1999, Sampling procedures for inspection by attributes — Part 1: Sampling plans indexed by
acceptable quality limit (AQL) for lot-by-lot inspection
ISO 3601-1, Fluid power systems — O-rings — Part 1: Inside diameters, cross sections, tolerances and size
identification code
ISO 3601-3, Fluid power systems — O-rings — Part 3: Quality acceptance criteria
ISO 9000:2000, Quality management systems — Fundamentals and vocabulary
ISO 11960, Petroleum and natural gas industries — Steel
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.