Small craft - Builder's plate (ISO 14945:2004)

ISO 14945:2004 establishes requirements for the uniform display of information to be exhibited on the builder's plate of small craft with a hull length LH of up to 24 m, measured according to ISO 8666. Excluded are inflatable boats covered by ISO 6185 and personal watercraft covered by ISO 13590.

Kleine Wasserfahrzeuge - Hersteller-Schild (ISO 14945:2004)

Diese Internationale Norm legt Anforderungen an die einheitliche Darstellung von Informationen auf einem Kennzeichnungsschild des Herstellers von kleinen Wasserfahrzeugen mit einer Rumpflänge LH bis 24 m in Übereinstimmung mit ISO 8666 fest.
Ausgenommen sind aufblasbare Boote, die durch ISO 6185 und Wasserskooter, die durch ISO 13590 abgedeckt sind.

Petits navires - Plaque du constructeur (ISO 14945:2004)

L'ISO 14945:2004 fixe des exigences qui permettent de présenter de manière uniforme les informations à porter sur la plaque du constructeur des petits navires dont la longueur de coque, LH, mesurée conformément à l'ISO 8666, est inférieure ou égale à 24 m. Sont exclus les bateaux pneumatiques couverts par l'ISO 6185 et les motos aquatiques qui relèvent de l'ISO 13590.

Mala plovila - Oznaka proizvajalca (Zahteve za poenoten prikaz podatkov na proizvajalčevi plošči na malih plovilih) (ISO 14945:2004)

General Information

Status
Withdrawn
Publication Date
31-Aug-2004
Withdrawal Date
15-Aug-2021
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
02-Aug-2021
Due Date
25-Aug-2021
Completion Date
16-Aug-2021

Relations

Buy Standard

Standard
EN ISO 14945:2004
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 14945:2004
01-september-2004
0DODSORYLOD2]QDNDSURL]YDMDOFD =DKWHYH]DSRHQRWHQSULND]SRGDWNRYQD
SURL]YDMDOþHYLSORãþLQDPDOLKSORYLOLK  ,62
Small craft - Builder's plate (ISO 14945:2004)
Kleine Wasserfahrzeuge - Hersteller-Schild (ISO 14945:2004)
Petits navires - Plaque du constructeur (ISO 14945:2004)
Ta slovenski standard je istoveten z: EN ISO 14945:2004
ICS:
47.080
SIST EN ISO 14945:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

INTERNATIONAL ISO
STANDARD 14945
First edition
2004-04-01


Small craft — Builder's plate
Petits navires — Plaque du constructeur




Reference number
ISO 14945:2004(E)
©
ISO 2004

---------------------- Page: 2 ----------------------

ISO 14945:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 3 ----------------------

ISO 14945:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 General requirements. 2
5 Displayed information. 2
Annex A (informative) Design and examples of builder’s plates. 4
Bibliography . 6

© ISO 2004 – All rights reserved iii

---------------------- Page: 4 ----------------------

ISO 14945:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14945 was prepared by Technical Committee ISO/TC 188, Small craft.
iv © ISO 2004 – All rights reserved

---------------------- Page: 5 ----------------------

ISO 14945:2004(E)
Introduction
The reason underlying the preparation of this International Standard is that the European Recreational Craft
Directive (Directive 94/25/EC) makes it compulsory that all recreational craft within the scope of the directive
shall be labelled with a builder’s plate containing specified information. This applies to boats built inside the
European Union (EU) as well as boats from other countries intended to be marketed in EU countries.
As the recreational craft market is operating worldwide, it seems to be advisable to create an International
Standard thus making the requirements of the builder’s plate known to manufacturers in countries inside and
outside the EU to facilitate marketing their boats in EU countries without additional requirements as to
labelling.

© ISO 2004 – All rights reserved v

---------------------- Page: 6 ----------------------

INTERNATIONAL STANDARD ISO 14945:2004(E)

Small craft — Builder's plate
1 Scope
This International Standard establishes requirements for the uniform display of information to be exhibited on
the builder’s plate of small craft with a hull length L of up to 24 m, measured according to ISO 8666.
H
Excluded are inflatable boats covered by ISO 6185 and personal watercraft covered by ISO 13590.
2 Normative references
The following referenced documents a
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.