iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1453-1:2000

(Main)

Plastics piping systems with structured wall-pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system

Plastics piping systems with structured wall-pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system

This standard specifies the requirements for pipes, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems with structured-wall pipes intended to be used for soil and waste discharge (low and high temperature) inside buildings (marked with "B"). It also specifies the test parameters for the test methods referred to in this standard. It covers pipes with an external and internal smooth layer which are connected with faomed PVC-U or by radial legs in solid PVC-U. The fully foamed PVC-U pipes and spiraly wound PVC-U pipes are not covered by this standard.

Kunststoff-Rohrleitungssysteme mit Rohren mit profilierter Wandung und glatten Rohroberflächen zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebäuden - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 1: Anforderungen an Rohre und das Rohrleitungssystem

Diese Norm legt fu(r Rohrleitungssysteme aus weichmacherfreiem Polyvinylchlorid  (PVC-U) Anforderungen an Rohre mit profilierter Wandung und glatten Rohroberfla(chen und das System fu(r Abwasserleitungen fest, die in Schwerkraftentwa(sserungssystemen innerhalb von Geba(uden (Anwendungskennzeichen "B") zum Ableiten von Abwasser (niedriger und hoher Temperatur) eingesetzt werden. Sie legt auch die Pru(fparameter fu(r die Pru(fverfahren fest, auf die in dieser Norm verwiesen wird.

Systemes de canalisations en plastique avec des tubes a paroi structurée pour l'évacuation des eaux-vannes et des eaux usées (a basse et a haute température) a l'intérieur des bâtiments - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 1: Spécifications pour tubes et le systeme

Cette norme spécifie les exigences pour les tubes a parois structurées et le systeme fabriqués a partir de poly(chlorure de vinyle) non plastifié (PVC-U), destinés a etre utilisés pour l'évacuation des eaux-vannes et des eaux usées (a basse et a haute température) a l'intérieur des bâtiments (marqués "B"). Elle spécifie aussi les parametres d'essais pour les méthodes d'essais référencées dans cette norme.

Cevni sistemi iz polimernih materialov s strukturirano steno cevi za nizko- in visokotemperaturne odvodne sisteme v stavbah - Nemehčan polivinilklorid (PVC-U) - 1. del: Specifikacije za cevi in sistem

General Information

Status
Withdrawn
Publication Date
31-May-2000
Withdrawal Date
19-Feb-2017
ICS
23.040.01 - Pipeline components and pipelines in general
91.140.80 - Drainage systems
Technical Committee
PCV - Plastic pipes, fittings and valves
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
20-Feb-2017
Due Date
15-Mar-2017
Completion Date
20-Feb-2017
Directive
89/106/EEC - Construction products
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
EN 1453-1:2000 - Plastics piping systems with structured wall-pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system

Relations

Replaced By
SIST EN 1453-1:2017 - Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system
Effective Date
01-Mar-2017

Buy Standard

EN 1453-1:2000EN 1453-1:2000
PreviousNext
Standard
EN 1453-1:2000
English language
26 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme mit Rohren mit profilierter Wandung und glatten Rohroberflächen zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebäuden - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 1: Anforderungen an Rohre und das RohrleitungssystemSystemes de canalisations en plastique avec des tubes a paroi structurée pour l'évacuation des eaux-vannes et des eaux usées (a basse et a haute température) a l'intérieur des bâtiments - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 1: Spécifications pour tubes et le systemePlastics piping systems with structured wall-pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and th
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1401-1:2019+A1:2023(Main + Amendment)
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
EN 1401-1:2019+A1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC U) piping systems in the field of non-pressure underground drainage and sewerage:
- buried in ground outside the building structure (application area code "U"), and
- both buried in ground, within the building structure and outside the building (application area code "UD").
NOTE 1   The intended use is reflected in the marking of products by "U" or "UD".
It also specifies the test parameters for the test methods referred to in this document.
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 13476-2 [1].
This document covers a range of nominal sizes, a range of pipes and fittings series and a range of stiffness classes and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to PVC U pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 16.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1455-1:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Specifications for pipes, fittings and the system
EN 1455-1:2022

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) piping systems intended for soil and waste discharge applications (low and high temperature):
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 1   The intended use is reflected in the marking of products by "B" or "BD".
NOTE 2   Application "B" covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3   Pipes and fittings of the pipe series S 25 are intended to be used for application area "B" only.
NOTE 4   For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm.
NOTE 5   EN 476 [1] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements.
This document is also applicable to ABS and ASA pipes, fittings and the system intended for the following purposes:
-   ventilating part of the pipework in association with discharge applications;
-   rainwater pipework within the building structure.
It also specifies the test parameters for the test method that are referred to.
This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 6   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1566-1:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
EN 1566-1:2022

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended for soil and waste discharge (low and high temperature) :
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 1   The intended use is reflected in the marking of products by "B" or "BD".
NOTE 2   Application "B" covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3   Pipes and fittings of the pipe series S 25 are intended to be used for application area "B" only.
NOTE 4   For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm.
NOTE 5   EN 476 [1] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements.
This document is applicable to PVC-C pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following purposes:
-   ventilating part of the pipework in association with discharge applications;
-   rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipe series and gives recommendations concerning colours.
NOTE 6   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices codes.
NOTE 7   Pipes, fitting and other components conforming to any of the plastics product standards listed Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1519-1:2019/AC:2021(Corrigendum)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Requirements for pipes, fittings and the system
EN 1519-1:2019/AC:2021

2021-02-24 - TC - Correcting some editorial aspects in Table 13

  • Corrigendum
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 1519-2:2020(Main)
Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity
CEN/TS 1519-2:2020

This document gives requirements and guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with EN 1519 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If certification is involved, it is recommended that the certification body is compliant with either EN ISO/IEC 17065 [2] or EN ISO/IEC 17021-series [4], as applicable.
NOTE 3   A basic test matrix providing an overview of the testing scheme is given in Annex A.
In conjunction with EN 1519-1 this document is applicable to piping systems made of polyethylene (PE) intended to be used:
-   for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B") and
-   for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD").
This is reflected in the marking of products by "B" or "BD".

  • Technical specification
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 17176-7:2020(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 7: Assessment of conformity
CEN/TS 17176-7:2020

This document gives requirements and guidance for the assessment of conformity of compounds/formulations, products, joints and assemblies in accordance with the applicable parts of EN 17176 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If certification is involved, it is recommended that the certification body is accredited to EN ISO/IEC 17065 [2] or ENISO/IEC 17021 [3], as applicable.
NOTE 3   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 17176-1, EN 17176-2, CEN/TS 17176-3 and EN 17176-5, this document is applicable to oriented unplasticized poly(vinyl chloride) (PVC-O) plastics piping systems for water supply and for buried and above-ground drainage, sewerage and irrigation under pressure.

  • Technical specification
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17176-5:2019(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 5: Fitness for purpose of the system
EN 17176-5:2019

This part of prEN 17176 specifies the characteristics for the fitness for purpose of oriented unplasticized poly(vinyl chloride) (PVC-O) piping systems intended for water supply, pressurized sewer systems and irrigation systems to be used underground or above-ground where protected to direct sunlight.
In conjunction with prEN 17176-2, prEN 17176-3, EN ISO 1452 3, EN ISO 1452 4 and EN 12842 this part is applicable to PVC-O pipes, PVC-O and PVC-U fittings, cast iron fittings and valves, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following:
a)   water mains and services lines;
b)   conveyance of water for both outside and inside buildings;
c)   drainage and sewerage under pressure;
d)   irrigation under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water and water for irrigation under pressure.
This part of prEN 17176 is also applicable for the conveyance of water, waste water and water for irrigation up to and including 45 °C. For temperatures between 25 °C and 45 °C, prEN 17176-2:2017, Figure C.1 applies.
NOTE    It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1519-1:2019(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Requirements for pipes, fittings and the system
EN 1519-1:2019

This standard specifies the requirements for pipes, fittings and the system of polyethylene (PE) solid-wall piping systems in the field of soil and waste discharge - inside buildings (marked with "B") and - for both inside buildings and buried in ground within the building structure (marked with "BD"). It also specifies the test parameters for the test methods referred to in this standard.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1453-1:2017/AC:2017(Corrigendum)
Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system
EN 1453-1:2017/AC:2017

Corrigendum issued due to mistake from TC in Table B.1 and in Clause 2 (SV on 2017-06-02)

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 1453-2:2017(Main)
Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
CEN/TS 1453-2:2017

This Technical Specification gives guidance for the assessment of conformity of formulations, products and assemblies in accordance with FprEN 1453 1:2016 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
If certification is involved, it is recommended that the certification body is preferably compliant with EN ISO/IEC 17065 [5] or EN ISO/IEC 17021 [3], as applicable.
In order to help the reader, a basic test matrix is given in Annex A, Table A.1.
In conjunction with FprEN 1453 1:2016, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC-U) intended to be used for the following purposes:
-   for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B");
This is reflected in the marking of products by "B".

  • Technical specification
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day