SIST EN ISO 10563:2017
(Main)Buildings and civil engineering works - Sealants - Determination of change in mass and volume (ISO 10563:2017)
Buildings and civil engineering works - Sealants - Determination of change in mass and volume (ISO 10563:2017)
This document specifies a method for the determination of the change of mass and the change of volume of self-levelling and non-sagging sealants used in joints in building construction.
NOTE This test procedure is not intended to determine the absolute maximum value of loss of volume of a tested sealant, but it is an indicative measurement of the loss of volume under specified parameters.
Hochbau - Fugendichtstoffe - Bestimmung der Änderung von Masse und Volumen (ISO 10563:2017)
Diese Internationale Norm legt ein Verfahren zur Bestimmung der Änderung von Masse und Volumen von selbstnivellierenden und fließbeständigen Fugendichtstoffen fest, die zur Abdichtung von Fugen im Hochbau verwendet werden.
ANMERKUNG Dieses Prüfverfahren ist nicht zur Bestimmung des absoluten maximalen Volumenverlustes von geprüften Fugendichtstoffen vorgesehen. Dennoch liefert es Anhaltswerte für den Volumenverlust unter bestimmten Parametern.
Bâtiments et ouvrages de génie civil - Mastics - Détermination des variations de masse et de volume (ISO 10563:2017)
ISO 10563:2017 spécifie une méthode pour la détermination des variations de masse et de volume des mastics autonivelants et non coulables utilisés dans des joints dans la construction immobilière.
Stavbe in gradbeni inženirski objekti - Tesnilne mase - Ugotavljanje spremembe mase in prostornine (ISO 10563:2017)
Ta dokument določa metodo za ugotavljanje spremembe mase in prostornine samoizravnalnih in nepolzečih tesnilnih mas, ki se uporabljajo za stike v stavbah.
OPOMBA: Ta preskusni postopek ni namenjen ugotavljanju absolutnih najvišjih vrednosti izgube prostornine preskušane tesnilne mase, temveč je indikativna meritev izgube prostornine na podlagi podanih parametrov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10563:2017
01-september-2017
1DGRPHãþD
SIST EN ISO 10563:2005
Stavbe in gradbeni inženirski objekti - Tesnilne mase - Ugotavljanje spremembe
mase in prostornine (ISO 10563:2017)
Buildings and civil engineering works - Sealants - Determination of change in mass and
volume (ISO 10563:2017)
Hochbau - Fugendichtstoffe - Bestimmung der Änderung von Masse und Volumen (ISO
10563:2017)
Bâtiments et ouvrages de génie civil - Mastics - Détermination des variations de masse
et de volume (ISO 10563:2017)
Ta slovenski standard je istoveten z: EN ISO 10563:2017
ICS:
17.060 Merjenje prostornine, mase, Measurement of volume,
gostote, viskoznosti mass, density, viscosity
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
SIST EN ISO 10563:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10563:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 10563:2017
EN ISO 10563
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2017
EUROPÄISCHE NORM
ICS 91.100.50 Supersedes EN ISO 10563:2005
English Version
Buildings and civil engineering works - Sealants -
Determination of change in mass and volume (ISO
10563:2017)
Bâtiments et ouvrages de génie civil - Mastics - Hochbau - Fugendichtstoffe - Bestimmung der
Détermination des variations de masse et de volume Änderung von Masse und Volumen (ISO 10563:2017)
(ISO 10563:2017)
This European Standard was approved by CEN on 22 April 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10563:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10563:2017
EN ISO 10563:2017 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10563:2017
EN ISO 10563:2017 (E)
European foreword
This document (EN ISO 10563:2017) has been prepared by Technical Committee ISO/TC 59 "Buildings
and civil engineering works".
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2017 and conflicting national standards
shall be withdrawn at the latest by December 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10563:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10563:2017 has been approved by CEN as EN ISO 10563:2017 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10563:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 10563:2017
INTERNATIONAL ISO
STANDARD 10563
Third edition
2017-05
Buildings and civil engineering
works — Sealants — Determination of
change in mass and volume
Bâtiments et ouvrages de génie civil — Mastics — Détermination des
variations de masse et de volume
Reference number
ISO 10563:2017(E)
©
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 10563:2017
ISO 10563:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10563:2017
ISO 10563:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and materials. 1
6 Preparation of test specimens . 2
6.1 For non-sagging sealant . 2
6.2 For self-levelling sealant . 2
7 Test procedure . 3
7.1 General . 3
7.2 Preconditioning . 3
7.3 Specific conditioning . 3
8 Calculation and expression of results . 3
8.1 Change in mass . 3
8.2 Change in volume. 4
9 Test report . 4
© ISO 2017 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10563:2017
ISO 10563:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www
...
SLOVENSKI STANDARD
oSIST prEN ISO 10563:2015
01-november-2015
Stavbe in gradbeni inženirski objekti - Tesnilne mase - Ugotavljanje spremembe
mase in prostornine (ISO/DIS 10563:2015)
Buildings and civil engineering works - Sealants - Determination of change in mass and
volume (ISO/DIS 10563:2015)
Hochbau - Fugendichtstoffe - Bestimmung der Änderung von Masse und Volumen
(ISO/DIS 10563:2015)
Construction immobilière - Mastics - Détermination des variations de masse et de
volume (ISO/DIS 10563:2015)
Ta slovenski standard je istoveten z: prEN ISO 10563
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
oSIST prEN ISO 10563:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 10563:2015
---------------------- Page: 2 ----------------------
oSIST prEN ISO 10563:2015
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10563
ISO/TC 59/SC 8 Secretariat: SAC
Voting begins on: Voting terminates on:
2015-09-03 2015-12-03
Buildings and civil engineering works — Sealants —
Determination of change in mass and volume
Construction immobilière — Mastics — Détermination des variations de masse et de volume
ICS: 91.100.50
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 10563:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015
---------------------- Page: 3 ----------------------
oSIST prEN ISO 10563:2015
ISO/DIS 10563:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 10563:2015
ISO/DIS 10563
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national
standards bodies (ISO member bodies). The work of preparing International Standards is normally
carried out through ISO technical committees. Each member body interested in a subject for which a
technical committee has been established has the right to be represented on that committee.
International organizations, governmental and non-governmental, in liaison with ISO, also take part in
the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO's adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 59, Buildings and civil engineering works,
Subcommittee SC 8, Sealants.
iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 10563:2015
---------------------- Page: 6 ----------------------
oSIST prEN ISO 10563:2015
ISO/DIS 10563
Buildings and Civil Engineering Works — Sealants —
Determination of change in mass and volume
1 Scope
This International Standard specifies a method for the determination of the change of mass and the
change of volume of self levelling and non sagging sealants used in joints in building construction.
Note: this test procedure is not intended to determine the absolute maximum value of loss of volume of a tested sealant, but it
is an indicative measurement of the loss of volume under specified parameters.
2 Normative reference
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 6927, Buildings and civil engineering works — Sealants — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6927 apply.
4 Principle
Test specimens consist either in metal rings filled with non sagging sealant, or in metal moulds filled
with self levelling sealant. The rings or moulds are weighed in air and in water, before and after filling,
before and after specific conditioning. The change in mass and in volume of the tested sealant is
calculated.
5 Apparatus and materials
5.1 Rings of non-corrosive metal for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.