SIST ENV 1122:1999
(Main)Determination of cadmium in plastics with the method of the wet decomposition
Determination of cadmium in plastics with the method of the wet decomposition
This European Standard describes a method for the determination of the total Cadmium (CD) content in plastics in the range of 10mg Cd/kg to 3.000mg Cd/kg. It is not suitable for polyfluorated plastic materials.
Bestimmung von Cadmium in Kunststoffen nach dem Naßaufschluß
Détermination du cadmium dans les plastiques d'apres la méthode de décomposition par voie humide
La présente norme européenne décrit une méthode de dosage du cadmium dans les plastiques présentant une teneur totale comprise entre 10mg Cd/gk et 3 000mg Cd/kg.
Določevanje kadmija v polimernih materialih z metodo mokrega razklopa
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ENV 1122:1999
01-maj-1999
'RORþHYDQMHNDGPLMDYSROLPHUQLKPDWHULDOLK]PHWRGRPRNUHJDUD]NORSD
Determination of cadmium in plastics with the method of the wet decomposition
Bestimmung von Cadmium in Kunststoffen nach dem Naßaufschluß
Détermination du cadmium dans les plastiques d'apres la méthode de décomposition par
voie humide
Ta slovenski standard je istoveten z: ENV 1122:1995
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST ENV 1122:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ENV 1122:1999
...
This May Also Interest You
This document specifies two methods, A and B, for determining the pourability of plastics in powdered and granular form, by measuring the flow time through a funnel under specified conditions.
From method A, information concerning the processability can be derived, whilst method B is especially designed for process control during manufacture.
The methods specified are not necessarily applicable to all plastics in powdered and granular form.
- Standard11 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft8 pagesEnglish languagesale 10% offe-Library read for×1 day
ISO 179-1:2010 specifies a method for determining the Charpy impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
The method can be used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions. It can also be used for the determination of comparative data from similar types of material.
The method has a greater range of applicability than that given in ISO 180 (Izod impact testing) and is more suitable for the testing of materials showing interlaminar shear fracture or of materials exhibiting surface effects due to environmental factors.
The method is suitable for use with the following range of materials:
rigid thermoplastic moulding and extrusion materials (including filled and reinforced compounds in addition to unfilled types) and rigid thermoplastics sheets;
rigid thermosetting moulding materials (including filled and reinforced compounds) and rigid thermosetting sheets (including laminates);
fibre-reinforced thermosetting and thermoplastic composites incorporating unidirectional or multi-directional reinforcements (such as mats, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings and milled fibres) or incorporating sheets made from pre-impregnated materials (prepregs), including filled compounds;
thermotropic liquid-crystal polymers.
- Standard30 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft27 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies a test method for the determination of puncture impact properties of rigid plastics, in the form of flat specimens, using instruments for measuring force and deflection. It is applicable if a force-deflection or force-time diagram, recorded at nominal constant striker velocity, is necessary for detailed characterization of the impact behaviour.
The test method is applicable to specimens with a thickness between 1 mm to 4 mm.
The method is suitable for use with the following types of material:
— rigid thermoplastic moulding and extrusion materials, including filled, unfilled and reinforced compounds and sheets;
— rigid thermosetting moulding and extrusion materials, including filled and reinforced compounds, sheets and laminates;
— fibre-reinforced thermoset and thermoplastic composites incorporating unidirectional or multi-directional reinforcements such as mats, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings, milled fibres and sheets made from pre-impregnated materials (prepregs).
The method is also applicable to specimens which are either moulded or machined from finished products, laminates and extruded or cast sheet.
The test results are comparable only if the conditions of preparation of the specimens, their dimensions and surfaces as well as the test conditions are the same. In particular, results determined on specimens of different thickness cannot be compared with one another (see Annex E). Comprehensive evaluation of the reaction to impact stress can be obtained by determinations made as a function of impact velocity and temperature for different material variables, such as crystallinity and moisture content.
The impact behaviour of finished products cannot be predicted directly from this test, but specimens may be taken from finished products (see above) for tests by this method.
Test data developed by this method is not intended to be used for design calculations. However, information on the typical behaviour of the material can be obtained by testing at different temperatures and impact velocities (see Annex D) by varying the thickness (see Annex E) and by testing specimens prepared under different conditions.
It is not the purpose of this document to give an interpretation of the mechanism occurring on every particular point of the force-deflection diagram. These interpretations are a task for scientific research.
- Standard42 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft34 pagesEnglish languagesale 10% offe-Library read for×1 day
1.1 This document specifies a method for determining the Izod impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
1.2 The method is used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions.
1.3 The method is suitable for use with the following range of materials:
— rigid thermoplastic moulding and extrusion materials, including filled and reinforced compounds in addition to unfilled types; rigid thermoplastics sheets;
— rigid thermosetting moulding materials, including filled and reinforced compounds; rigid thermosetting sheets, including laminates;
— fibre-reinforced thermosetting and thermoplastic composites incorporating unidirectional or non-unidirectional reinforcements such as mat, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings and milled fibres and sheet made from pre-impregnated materials (prepregs);
— thermotropic liquid-crystal polymers.
1.4 The method is not normally suitable for use with rigid cellular materials and sandwich structures containing cellular material. Notched specimens are also not normally used for long-fibre-reinforced composites or thermotropic liquid-crystal polymers.
1.5 The method is suited to the use of specimens which can be either moulded to the chosen dimensions, machined from the central portion of a standard multipurpose test specimen (see ISO 20753) or machined from finished or semi-finished products such as mouldings, laminates and extruded or cast sheet.
1.6 The method specifies preferred dimensions for the test specimen. Tests which are carried out on specimens of different dimensions or with different notches, or specimens which are prepared under different conditions, may produce results which are not comparable. Other factors, such as the energy capacity of the apparatus, its impact velocity and the conditioning of the specimens can also influence the results. Consequently, when comparative data are required, these factors are to be carefully controlled and recorded.
1.7 The method is not intended to be used as a source of data for design calculations. Information on the typical behaviour of a material can be obtained, however, by testing at different temperatures, by varying the notch radius and/or the thickness and by testing specimens prepared under different conditions.
- Standard22 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft18 pagesEnglish languagesale 10% offe-Library read for×1 day
ISO 11357-1:2016 specifies several differential scanning calorimetry (DSC) methods for the thermal analysis of polymers and polymer blends, such as
- thermoplastics (polymers, moulding compounds and other moulding materials, with or without fillers, fibres or reinforcements),
- thermosets (uncured or cured materials, with or without fillers, fibres or reinforcements), and
- elastomers (with or without fillers, fibres or reinforcements).
ISO 11357-1:2016 is intended for the observation and measurement of various properties of, and phenomena associated with, the above-mentioned materials, such as
- physical transitions (glass transition, phase transitions such as melting and crystallization, polymorphic transitions, etc.),
- chemical reactions (polymerization, crosslinking and curing of elastomers and thermosets, etc.),
- the stability to oxidation, and
- the heat capacity.
ISO 11357-1:2016 specifies a number of general aspects of differential scanning calorimetry, such as the principle and the apparatus, sampling, calibration and general aspects of the procedure and test report common to all following parts.
Details on performing specific methods are given in subsequent parts of ISO 11357 (see Foreword).
- Standard43 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft40 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies a method for the determination of the density of liquid resins using a pycnometer.
- Standard8 pagesEnglish languagesale 10% offe-Library read for×1 day
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Draft4 pagesEnglish languagesale 15% off
- Draft4 pagesEnglish languagesale 15% off
This document specifies a method of determining the bulk factor of a moulding material based on the ratio of the apparent volumetric density of a given quantity of particles and the corresponding material density.
- Standard6 pagesEnglish languagesale 10% offe-Library read for×1 day
- Standard2 pagesEnglish languagesale 15% off
- Draft2 pagesEnglish languagesale 15% off
- Draft2 pagesEnglish languagesale 15% off
This document specifies a method for the determination of the density of liquid resins using a pycnometer.
- Standard11 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft8 pagesEnglish languagesale 10% offe-Library read for×1 day
This document summarizes the state of standardization in the field of biodegradable plastics and plastics products at CEN and ISO level. It explains the underlying scientific principles of biodegradation that provide the foundations for relevant test methods and enters into the merits of the individual tests to explain and clarify the reasons for the adoption of specific solutions and criteria.
In a second part, this document highlights areas where standardisation in this field is currently lacking and where future developments may be anticipated and useful.
- Technical report43 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies test procedures for the acquisition and presentation of multipoint data on the
following thermal and processing properties of plastics:
— enthalpy/temperature curve;
— linear-expansion/temperature curve;
— melt shear viscosity.
- Standard16 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft13 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.