SIST EN ISO 15083:2020
(Main)Small craft - Bilge-pumping systems (ISO 15083:2020)
Small craft - Bilge-pumping systems (ISO 15083:2020)
EN-ISO 15083 specifies requirements for pumping or alternative means designed to remove normal accumulations of bilge water for small craft with a length of hull, LH, as defined in ISO 8666:2016, of up to 24 m.$0This document does not set requirements for bilge pumps or bilge-pumping systems designed for damage control.
Kleine Wasserfahrzeuge - Lenzeinrichtungen (ISO 15083:2020)
Dieses Dokument legt Anforderungen für das Abpumpen oder alternative Möglichkeiten zum Entfernen von üblichen Mengen von Wasser fest, das sich in der Bilge ansammelt. Es gilt für kleine Wasserfahrzeuge mit einer Rumpflänge LH bis 24 m wie in ISO 8666:2016 festgelegt.
Dieses Dokument legt keine Anforderungen für Lenzpumpen oder Lenzeinrichtungen zum Zwecke der Leckbegrenzung fest.
Petit navires - Systèmes de pompes de cale (ISO 15083:2020)
Le présent document spécifie les exigences relatives au pompage ou moyens alternatifs conçus pour évacuer les accumulations normales d'eau de cale pour les petits navires d'une longueur de coque LH, comme définie dans l'ISO 8666:2016 est inférieure ou égale à 24 m.
Ce document ne définit pas les exigences applicables aux pompes de cale ou aux systèmes de pompage de cale conçus pour contrôler les avaries de coque.
Mala plovila - Kalužni sistemi (na čolnih) (ISO 15083:2020)
Standard EN ISO 15083 določa zahteve za črpanje ali alternativne načine odstranjevanja običajnih količin nakopičene kalužne vode za mala plovila z dolžino trupa (LH) do 24 m, kot je opredeljeno v standardu ISO 8666:2016. Ta dokument ne določa zahtev za kalužne črpalke ali kalužne sisteme, namenjene za obvladovanje poškodb.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15083:2020
01-julij-2020
Nadomešča:
SIST EN ISO 15083:2018
Mala plovila - Kalužni sistemi (na čolnih) (ISO 15083:2020)
Small craft - Bilge-pumping systems (ISO 15083:2020)
Kleine Wasserfahrzeuge - Lenzeinrichtungen (ISO 15083:2020)
Petit navires - Systèmes de pompes de cale (ISO 15083:2020)
Ta slovenski standard je istoveten z: EN ISO 15083:2020
ICS:
47.080 Čolni Small craft
SIST EN ISO 15083:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15083:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 15083:2020
EN ISO 15083
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2020
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 15083:2018
English Version
Small craft - Bilge-pumping systems (ISO 15083:2020)
Petit navires - Systèmes de pompes de cale (ISO Kleine Wasserfahrzeuge - Lenzeinrichtungen (ISO
15083:2020) 15083:2020)
This European Standard was approved by CEN on 18 March 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15083:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15083:2020
EN ISO 15083:2020 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15083:2020
EN ISO 15083:2020 (E)
European foreword
This document (EN ISO 15083:2020) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards shall
be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15083:2018.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15083:2020 has been approved by CEN as EN ISO 15083:2020 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15083:2020
EN ISO 15083:2020 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of
Directive 2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) Remarks/Notes
Directive 2013/53/EU of this EN
Annex I, Clause 3.5 Clause 1 to 7 This European Standard is
applicable to watercraft within the
scope of Directive 2013/53/EU,
Article 2.1(a) and 2.1(b).
This European Standard specifies
requirements for pumping or other
means designed to remove normal
accumulation of bilge water only. It
excludes:
— Requirements for bilge pumps
or bilge pumping systems
designed for damage control.
— Cockpits and wells,
— Ventilation fittings.
Annex I, Clause 2.5 Clause 8
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 15083:2020
INTERNATIONAL ISO
STANDARD 15083
Second edition
2020-04
Small craft — Bilge-pumping systems
Petit navires — Systèmes de pompe de cale
Reference number
ISO 15083:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 15083:2020
ISO 15083:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 15083:2020
ISO 15083:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and codes . 3
5 Requirements . 3
5.1 Type, number and location . 3
5.1.1 General requirements . 3
5.1.2 Non fully enclosed boats . 4
5.1.3 Fully enclosed boats . 4
5.2 Summary of requirements . 4
5.3 Capacity . 5
6 Design and construction . 5
6.1 General . 5
6.2 Electrically operated pumps . 5
7 Installation . 6
8 Owner’s manual. 7
8.1 General . 7
8.2 Information for the owner/operator . 7
8.3 Owners/operators responsibility . 7
8.4 Safety precautions . 7
8.4.1 Caution . 7
8.4.2 Warning . 7
8.5 Additional information . 7
Bibliography . 8
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 15083:2020
ISO 15083:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (ISO 15083:2003), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— the definitions have been updated (Clause 3);
— in 5.1.2, a requirement has been added for craft not fully enclosed with bilge compartments to have
a bilge pump system installed;
— exposed and enclosed steering position requirements have been removed from 5.1.3.2;
— a requirement has been added (7.13) for the system design to ensure that accidental discharge is
prevented.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 15083:2020
ISO 15083:2020(E)
Introduction
Bilge-pumping systems as specified in this document are limited to normal amounts of water in an
intact boat due to spray, ra
...
SLOVENSKI STANDARD
oSIST prEN ISO 15083:2019
01-april-2019
0DODSORYLOD.DOXåQLVLVWHPL QDþROQLK ,62',6
Small craft - Bilge-pumping systems (ISO/DIS 15083:2019)
Kleine Wasserfahrzeuge - Lenzeinrichtungen (ISO/DIS 15083:2019)
Petit navires - Systèmes de pompes de cale (ISO/DIS 15083:2019)
Ta slovenski standard je istoveten z: prEN ISO 15083
ICS:
47.080 ýROQL Small craft
oSIST prEN ISO 15083:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 15083:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 15083:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 15083
ISO/TC 188/SC 2 Secretariat: SIS
Voting begins on: Voting terminates on:
2019-01-31 2019-04-25
Small craft — Bilge-pumping systems
Petits navires — Systèmes de pompes de cale
ICS: 47.080
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 15083:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 15083:2019
ISO/DIS 15083:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 15083:2019
ISO/DIS 15083:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 3
5 Requirements . 3
5.1 Type, number and location . 3
5.1.1 General. 3
5.1.2 Open and partially decked boats with bilge compartments . 3
5.1.3 Fully decked boats . 4
5.2 Summary of requirements . 4
5.3 Capacity . 5
6 Design and construction . 5
6.1 General . 5
6.2 Electrically operated pumps . 5
7 Installation . 5
8 Owner’s manual. 6
8.1 Information for the owner/operator . 6
8.2 Owners/operators responsibility . 6
8.3 Safety precautions . 7
8.3.1 Caution . 7
8.3.2 Warning . 7
8.4 Information . 7
Annex A (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 8
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 15083:2019
ISO/DIS 15083:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 188, Small craft, Subcommittee SC 2,
Engines and propulsion systems.
This second edition cancels and replaces the first edition (ISO 15083:2003), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— xxx xxxxxxx xxx xxxx
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 15083:2019
ISO/DIS 15083:2019(E)
Introduction
Bilge- pumping systems as specified in this International Standard are limited to normal amounts of
water in an intact boat due to spray, rain, seepage, spillage, and occasional small amounts of water
shipped from boat movements in heavy weather.
This document is not intended to control flooding resulting from hull damage.
© ISO 2019 – All rights reserved v
---------------------- Page: 7 ----------------------
oSIST prEN ISO 15083:2019
---------------------- Page: 8 ----------------------
oSIST prEN ISO 15083:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 15083:2019(E)
Small craft — Bilge-pumping systems
1 Scope
This document specifies requirements for pumping or alternative means designed to remove normal
accumulations of bilge water for small craft with a hull length, L , up to 24 m according to ISO 8666.
H
This document does not set requirements for bilge pumps or bilge-pumping systems designed for
damage control.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 8666, Small craft — Principal data
ISO 8849, Small craft — Electrically operated direct-current bilge pumps
ISO 9093, Small craft — Seacocks and through-hull fittings
ISO 11812, Small craft — Watertight cockpits and quick-draining cockpits
ISO 12216, Small craft — Windows, portlights, hatches, deadlights and doors — Strength and watertightness
requirements
IEC 60529:2001, Degrees of protection provided by enclosures (IP Code)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
design category
description of the sea and wind conditions for which a boat is assessed to be suitable according to
ISO 8666
3.2
sailing boat
craft for which the primary means of propulsion is by wind power, having reference sail area (A ) ≥
S
2/3
0,07 (m )
LDC
3.3
non-sailing boat
craft for which the primary means of propulsion is other than by wind power, having reference sail area
2/3
(A ) <�0,07 (m )
S LDC
© ISO 2019 – All rights reserved 1
---------------------- Page: 9 ----------------------
oSIST prEN ISO 15083:2019
ISO/DIS 15083:2019(E)
3.4
fully enclosed boat
boat in which the horizontal projection of the sheerline area comprises any combination of
— watertight deck and superstructure, and/or
—
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.