SIST EN IEC 60317-74:2018

Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled rectangular aluminium wire, class 180 (IEC 60317-74:2018)

This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium
winding wire of class 180 with a sole coating based on polyesterimide resin, which can be
modified providing it retains the chemical identity of the original resin and meets all specified
wire requirements.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance or application characteristics.
The range of nominal conductor dimensions covered by this standard is:
– width: min. 2,0 mm max. 16,0 mm;
– thickness: min. 0,80 mm max. 5,60 mm.
Wires of grade 1 and grade 2 are included in this specification and apply to the complete
range of conductors.
The specified combinations of width and thickness as well as the specified width/thickness
ratio are given in IEC 60317-0-9:2015.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 74: Flachdrähte aus Aluminium, lackisoliert mit Polyesterimid, Klasse 180

Spécifications pour types particuliers de fils de bobinage - Partie 74: Fil de section rectangulaire émaillé en aluminium revêtu de polyesterimide, de classe 180

IEC 60317-74:2018 spécifie les exigences relatives aux fils de bobinage de section rectangulaire en aluminium émaillé de classe 180 à couche de revêtement unique en résine de polyesterimide. Cette couche de revêtement peut être modifiée à condition de conserver les propriétés chimiques de la résine d'origine et de respecter toutes les exigences spécifiées pour les fils. NOTE Une résine modifiée est une résine dont les propriétés chimiques ont été modifiées ou qui contient un ou plusieurs additifs visant à améliorer certaines performances ou caractéristiques d'application. La plage des dimensions nominales des conducteurs couvertes par la présente norme est:
- pour la largeur: min. 2,0 mm - max. 16,0 mm;
- pour l'épaisseur: min. 0,80 mm - max. 5,60 mm.
Les fils de grades 1 et 2 sont couverts par la présente spécification et s'appliquent à toute la gamme des conducteurs.
Les combinaisons largeur-épaisseur spécifiées ainsi que le rapport largeur/épaisseur spécifié sont indiqués dans l'IEC 60317-0-9:2015.
Mots clés: fils isolés utilisés pour les enroulements

Specifikacije za posebne vrste navijalnih žic - 74. del: Aluminijasta žica s pravokotnim prerezom, emajlirana s poliesterimidom, razred 180 (IEC 60317-74:2018)

Ta del standarda IEC 60317 določa zahteve za emajlirano aluminijasto navijalno žico s pravokotnim prerezom razreda 180 z eno samo prevleko na osnovi poliestramidske smole, ki se lahko spremeni, če ohrani kemijsko identiteto izvirne smole in izpolnjuje vse določene zahteve za žice.
OPOMBA: spremenjena smola je smola, ki je bila kemijsko spremenjena ali vsebuje enega ali več aditivov za izboljšanje določene lastnosti učinkovitosti ali uporabe.
Razpon nazivnih mer prevodnika, ki ga zajema ta standard, je:
– širina: min. 2,0 mm, maks. 16,0 mm;
– debelina: min. 0,80 mm, maks. 5,60 mm.
V to specifikacijo so vključene žice razreda 1 in 2 ter se uporabljajo za celoten nabor prevodnikov.
Navedene kombinacije širine in debeline ter določena razmerja med širino in debelino so podana v standardu IEC 60317-0-9:2015.

General Information

• Status: Published
• Public Enquiry End Date: 31-Aug-2017
• Publication Date: 14-May-2018
• ICS: 29.060.10 - Wires
• ICS: 77.150.10 - Aluminium products
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 25-Apr-2018
• Due Date: 30-Jun-2018
• Completion Date: 15-May-2018
• Ref Project: EN IEC 60317-74:2018 - Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled rectangular aluminium wire, class 180

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60317-74:2018
01-julij-2018
Specifikacije za posebne vrste navijalnih žic - 74. del: Aluminijasta žica s
pravokotnim prerezom, emajlirana s poliesterimidom, razred 180 (IEC 60317-
74:2018)
Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled
rectangular aluminium wire, class 180 (IEC 60317-74:2018)
Ta slovenski standard je istoveten z: EN IEC 60317-74:2018
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
SIST EN IEC 60317-74:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN IEC 60317-74:2018

---------------------- Page: 2 ----------------------

SIST EN IEC 60317-74:2018


EUROPEAN STANDARD EN IEC 60317-74

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2018
ICS 29.060.10

English Version
Specifications for particular types of winding wires - Part 74:
Polyesterimide enamelled rectangular aluminium wire, class 180
(IEC 60317-74:2018)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 74: Fil de section rectangulaire émaillé en aluminium Wickeldrähten - Teil 74: Flachdrähte aus Aluminium,
revêtu de polyesterimide, de classe 180 lackisoliert mit Polyesterimid, Klasse 180
(IEC 60317-74:2018) (IEC 60317-74:2018)
This European Standard was approved by CENELEC on 2018-04-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60317-74:2018 E

---------------------- Page: 3 ----------------------

SIST EN IEC 60317-74:2018
EN IEC 60317-74:2018 (E)


European foreword
The text of document 55/1635/FDIS, future edition 1 of IEC 60317-74, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60317-74:2018.

The following dates are fixed:
• latest date by which the document has to be (dop) 2019-01-03
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2021-04-03
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60317-74:2018 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60264 series NOTE Harmonized as EN 60264 series.
IEC 60317 series NOTE Harmonized as EN 60317 series.
IEC 60851 series NOTE Harmonized as EN 60851 series.
2

---------------------- Page: 4 ----------------------

SIST EN IEC 60317-74:2018
EN IEC 60317-74:2018 (E)

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.

NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60317-0-9 2015 Specifications for particular types of EN 60317-0-9 2015
winding wires - Part 0-9: General
requirements - Enamelled rectangular
aluminium wire


3

---------------------- Page: 5 ----------------------

SIST EN IEC 60317-74:2018

---------------------- Page: 6 ----------------------

SIST EN IEC 60317-74:2018



IEC 60317-74

®


Edition 1.0 2018-02




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Specifications for particular types of winding wires –

Part 74: Polyesterimide enamelled rectangular aluminium wire,class 180




Spécifications pour types particuliers de fils de bobinage –

Partie 74: Fil de section rectangulaire émaillé en aluminium revêtu de

polyesterimide, de classe 180















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.060.10 ISBN 978-2-8322-5417-2



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN IEC 60317-74:2018
– 2 – IEC 60317-74:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
9 Heat shock . 7
10 Cut-through . 7
11 Resistance to abrasion . 7
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 8
19 Dielectric dissipation factor . 8
20 Resistance to transformer oil . 8
21 Loss of mass .
...

SLOVENSKI STANDARD
oSIST prEN 60317-74:2017
01-september-2017
Specifikacije za posebne tipe navitij - 74. del: S poliesterimidom emajlirana
aluminijasta žica s pravokotnim prerezom, razred 180
Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled
rectangular aluminium wire, class 180
Ta slovenski standard je istoveten z: prEN 60317-74:2017
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
oSIST prEN 60317-74:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 60317-74:2017

---------------------- Page: 2 ----------------------
oSIST prEN 60317-74:2017
55/1613/CDV

COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60317-74 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2017-05-26 2017-08-18
SUPERSEDES DOCUMENTS:
55/1588/CD,55/1607/CC

IEC TC 55 : WINDING WIRES
SECRETARIAT: SECRETARY:
United States of America Mr Mike Leibowitz
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:

TC 2,TC 14
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:

EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.

This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.

TITLE:
Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled
rectangular aluminium wire, class 180

NOTE FROM TC/SC OFFICERS:


Copyright © 2017 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.

---------------------- Page: 3 ----------------------
oSIST prEN 60317-74:2017
IEC CDV 60317-74/Ed1  IEC:2017 – 2 – 55/1613/CDV
1 CONTENTS
2
3 FOREWORD . 3
4 INTRODUCTION . 5
5 1 Scope . 6
6 2 Normative references . 6
7 3 Terms, definitions, general notes and appearance . 6
8 3.1 Terms and definitions. 6
9 3.2 General notes . 6
10 3.2.1 Methods of test . 6
11 3.2.2 Winding wire . 6
12 3.3 Appearance . 6
13 4 Dimensions . 7
14 5 Electrical resistance . 7
15 6 Elongation . 7
16 7 Springiness . 7
17 8 Flexibility and adherence . 7
18 9 Heat shock . 7
19 10 Cut-through . 7
20 11 Resistance to abrasion . 7
21 12 Resistance to solvents . 7
22 13 Breakdown voltage . 7
23 14 Continuity of insulation . 7
24 15 Temperature index . 7
25 16 Resistance to refrigerants . 7
26 17 Solderability . 7
27 18 Heat or solvent bonding . 7
28 19 Dielectric dissipation factor . 7
29 20 Resistance to transformer oil . 8
30 21 Loss of mass . 8
31 23 Pin hole test . 8
32 30 Packaging . 8
33
34
35
36

---------------------- Page: 4 ----------------------
oSIST prEN 60317-74:2017
IEC CDV 60317-74/Ed1  IEC:2017 – 3 – 55/1613/CDV
37 INTERNATIONAL ELECTROTECHNICAL COMMISSION
38 ____________
39
40 SPECIFICATIONS FOR PARTICULAR TYPES
41
42 OF WINDING WIRES –
43
44 Part 74: Polyesterimide enamelled rectangular aluminium wire, class 180
45
46
47
48 FOREWORD
49 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
50 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
51 international co-operation on all questions concerning standardization in the electrical and electronic fields. To
52 this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
53 Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
54 Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
55 in the subject dealt with may participate in this preparatory work. International, governmental and non-
56 governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
57 with the International Organization for Standardization (ISO) in accordance with conditions determined by
58 agreement between the two organizations.
59 2) The formal decisions or agreements of IEC on technical ma
...