Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements (IEC 60309-1:1999/A2:2012)

Applies to plugs and socket-outlets, cable couplers and appliance couplers, with a rated operating voltage not exceeding 690 V d.c. or a.c. and 500 Hz a.c. and a rated current not exceeding 250 A, primarily intended for industrial use, either indoors or outdoors. The list of preferred ratings is not intended to exclude other ratings, requirements for which are under consideration. This European Standard applies to Series I products only. Series II products are not allowed and not suitable for use in Europe: reference and requirements for Series II products are reported in this standard for information only and shall be ignored. This European Standard applies to products intended to be used with cables with metric sizes (mm2) only. Reference and requirements to AWG and MCM cables are present in the relevant IEC publication and they are reported in this standard for information only. See Annex ZB for a list of references to Series II and/or AWG/MCM cable which are excluded from this standard.

Stecker, Steckdosen und Kupplungen für industrielle Anwendungen - Teil 1: Allgemeine Anforderungen (IEC 60309-1:1999/A2:2012)

Prises de courant pour usages industriels - Partie 1: Règles générales (CEI 60309-1:1999/A2:2012)

Vtiči, vtičnice in spojke za industrijske namene - 1. del: Splošne zahteve (IEC 60309-1:1999/A2:2012)

Standard se uporablja za vtiče in vtičnice, spojke kablov in aparatov z nazivno obratovalno napetostjo, ki ne presega 690 V enosmerne ali izmenične napetosti in frekvence 500 Hz, ter nazivnim tokom, ki ne presega 250 A, namenjene predvsem za industrijsko uporabo v notranjih prostorih ali na prostem. Seznam prednostnih nazivnih vrednosti ni namenjen izključitvi drugih nazivnih vrednosti, pri čemer so zahteve zanje v obravnavi. Ta evropski standard se uporablja samo za izdelke skupine I. Izdelki skupine II niso dovoljeni in niso primerni za uporabo v Evropi: sklicevanje in zahteve za izdelke skupine II so v tem standardu navedeni zgolj informativno in jih je treba prezreti. Ta evropski standard se uporablja samo za izdelke, ki so namenjeni uporabi s kabli z metričnimi velikostmi (mm2). Sklicevanje in zahteve za kable AWG in MCM so navedeni v ustrezni publikaciji IEC, pri čemer so v tem standardu navedeni zgolj informativno. Dodatek ZB zajema seznam sklicevanj na skupino II in/ali kable AWG/MCM, ki so izključeni iz tega standarda.

General Information

Status
Published
Publication Date
20-Sep-2012
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
30-Aug-2012
Due Date
04-Nov-2012
Completion Date
21-Sep-2012

Relations

Buy Standard

Amendment
EN 60309-1:2000/A2:2012
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60309-1:2000/A2:2012
01-oktober-2012
9WLþLYWLþQLFHLQVSRMNH]DLQGXVWULMVNHQDPHQHGHO6SORãQH]DKWHYH ,(&
$
Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements
(IEC 60309-1:1999/A2:2012)
Stecker, Steckdosen und Kupplungen für industrielle Anwendungen - Teil 1: Allgemeine
Anforderungen (IEC 60309-1:1999/A2:2012)
Prises de courant pour usages industriels - Partie 1: Règles générales (CEI 60309-
1:1999/A2:2012)
Ta slovenski standard je istoveten z: EN 60309-1:1999/A2:2012
ICS:
29.120.30 9WLþLYWLþQLFHVSRMNH Plugs, socket-outlets,
couplers
SIST EN 60309-1:2000/A2:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60309-1:2000/A2:2012

---------------------- Page: 2 ----------------------

SIST EN 60309-1:2000/A2:2012

EUROPEAN STANDARD
EN 60309-1/A2

NORME EUROPÉENNE
August 2012
EUROPÄISCHE NORM

ICS 29.120.30


English version


Plugs, socket-outlets and couplers for industrial purposes -
Part 1: General requirements
(IEC 60309-1:1999/A2:2012)


Prises de courant  Stecker, Steckdosen und Kupplungen
pour usages industriels - für industrielle Anwendungen -
Partie 1: Règles générales Teil 1: Allgemeine Anforderungen
(CEI 60309-1:1999/A2:2012) (IEC 60309-1:1999/A2:2012)





This amendment A2 modifies the European Standard EN 60309-1:1999; it was approved by CENELEC on
2012-07-13. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60309-1:1999/A2:2012 E

---------------------- Page: 3 ----------------------

SIST EN 60309-1:2000/A2:2012
EN 60309-1:1999/A2:2012 - 2 -

Foreword
The text of document 23H/282/FDIS, future edition 1 of IEC 60309-1:1999/A2, prepared by SC 23H,
"Industrial plugs and socket-outlets", of IEC TC 23, "Electrical accessories" was submitted to the
IEC CENELEC parallel vote and approved by CENELEC as EN 60309-1:1999/A2:2012.

The following dates are fixed:
(dop) 2013-04-13
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-07-13

standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.

Endorsement notice
The text of the International Standard IEC 60309-1:1999/A2:2012 was approved by CENELEC as a
European Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 60309-1:2000/A2:2012
- 3 - EN 60309-1:1999/A2:2012
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

Replace EN 60695-2-1:1996 by:

IEC 60695-2-11 - Fire hazard testing - EN 60695-2-11 -
Part 2-11: Glowing/hot-wire based test
methods - Glow-wire flammability test method
for end-products


Addition to Annex ZA of EN 60309-1:1999:

IEC 60309-4 - Plugs, socket-outlets and couplers for EN 60309-4 -
industrial purposes -
Part 4: Switched socket-outlets and
connectors with or without interlock


IEC 60695-10-2 - Fire hazard testing - EN 60695-10-2 -
Part 10-2: Abnormal heat - Ball pressure test

---------------------- Page: 5 ----------------------

SIST EN 60309-1:2000/A2:2012

---------------------- Page: 6 ----------------------

SIST EN 60309-1:2000/A2:2012



IEC 60309-1

®


Edition 4.0 2012-06




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE




AMENDMENT 2

AMENDEMENT 2





Plugs, socket-outlets and couplers for industrial purposes –

Part 1: General requirements




Prises de courant pour usages industriels –

Partie 1: Règles générales

















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX M


ICS 29.120.30 ISBN 978-2-83220-118-3



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60309-1:2000/A2:2012
– 2 – 60309-1 Amend.2 © IEC:2012

FOREWORD
This amendment has been prepared by subcommittee 23H: Industrial plugs and socket-outlets,
of IEC technical committee 23: Electrical accessories.
The text of this amendment is based on the following documents:
FDIS Report on voting
23H/282/FDIS 23H/285/RVD

Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________

1 Scope
Replace the first paragraph by:
This standard applies to plugs and socket-outlets, cable couplers and appliance couplers, with
a rated operating voltage not exceeding 1 000 V d.c. or a.c. and 500 Hz a.c., and a rated
current not exceeding 800 A, primarily intended for industrial use, either indoors or outdoors.
These accessories are intended to be installed by instructed persons (IEC 60050-195:1998,
Amendment 1:2001, 195-04-02) or skilled persons (IEC 60050-195:1998, Amendment 1:2001,
195-04-01) only.
Replace the fourth paragraph – introduced by Amendment 1 – by:
This standard applies to accessories with screwless type terminals or insulation piercing
terminals, with a rated current up to and including 32 A for series I and 30 A for series II.
3 Normative references
Replace IEC 60695-2-1:1994 by:
IEC 60695-2-11, Fire hazard testing –Part 2-11: Glowing/hot-wire based test methods – Glow-
wire flammability test method for end-products
Add the following references:

---------------------- Page: 8 ----------------------

SIST EN 60309-1:2000/A2:2012
60309-1 Amend.2 © IEC:2012 – 3 –
IEC 60309-4, Plugs, socket-outlets and couplers for industrial purposes – Part 4: Switched
socket-outlets and connectors with or without interlock
IEC 60695-10-2, Fire hazard testing – Part 10-2: Abnormal heat – Ball pressure test
4.1 General requirements
Add a new fourth paragraph:
Accessories shall have a minimum degree of protection IP23 according to IEC 60529.
5.1
Add the following new values
750 V
1 000 V
5.2
Add the following new values in Table 1:
315 300
400 350
630 500
800 600

Add after Table 1 the following Note 2:
NOTE 2 This table does not provide correspondence between series I and series II values. It is only a list of
preferred ratings
6.1.2
Replace the text introduced by Amendment 1 by the following:
"according to degrees of protection in accordance with IEC 60529 (with a minimum IP23, see
4.1)"
Add the following new subclause:
6.1.8 according to accessibility to live parts:
– accessories providing for IPXXB
– accessories providing for IP2X
– accessories providing for IPXXD
– accessories providing for IP4X
7.1
Replace, in the third dashed item, “alternative” by “alternating”.
Replace the seventh dashed item by “degree of protection”.
7.2
Replace the second paragraph after the list of symbols by:

---------------------- Page: 9 ----------------------

SIST EN 60309-1:2000/A2:2012
– 4 – 60309-1 Amend.2 © IEC:2012
Marking of degree(s) of protection on plugs and appliance inlets is only valid when those are
in engagement with a complementary accessory or with an attached cap, if any.
7.3
Replace in the third paragraph:
“the symbol for degree of protection, if required”
by:
"the degree of protection".
7.6
Replace the existing third sentence by:
After the humidity treatment of Clause 18, the marking is rubbed by hand for 15 s with a
piece of cloth soaked in water and again for 15 s with a piece of cloth soaked in petroleum
spirit.
It is recommended that the petroleum spirit used consist of a solvent hexane with an aromatic
content of maximum 0,1 volume percentage, a Kauri-Butanol value of approximately 29, an
initial boiling point of approximately 65 °C, a dry point of approximately 69 °C and a density of
3
approximately 0,68 g/ cm .
Table 2
Replace the value “690” by “1 000”.
7.9
Replace the last paragraph of this subclause – introduced by Amendment 1 – by:
This marking shall appear on the accessory. It may also appear on the accompanying
instruction sheet, the smallest package unit or the manufacturer's documentation, if any.
7.10
Replace the existing text of this subclause – introduced by Amendment 1 – by:
For terminals, the connection and disconnection procedures shall, if necessary, be indicated
on the product, on the smallest package unit or on the manufacturer’s documentation.
Table 3 – Size for connectable conductor
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.