SIST EN 60317-0-8:2012
(Main)Specifications for particular types of winding wires - Part 0-8: General requirements - Polyester glass-fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire
Specifications for particular types of winding wires - Part 0-8: General requirements - Polyester glass-fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire
This part of IEC 60317 specifies general requirements of polyester glass fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire. The range of nominal conductor dimensions is given in the relevant specification sheet.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-8: Allgemeine Anforderungen - Flachdrähte aus Kupfer, blank oder lackisoliert, mit Polyesterglasgewebe umsponnen und mit Harz oder Lack imprägniert oder nicht imprägniert
Spécifications pour types particuliers de fils de bobinage - Partie 0-8: Exigences générales - Fil de section rectangulaire en cuivre nu ou émaillé guipé de fibres de verre avec polyester, imprégnées ou non de vernis ou de résine
La CEI 60317-0-8:2012 spécifie les exigences générales pour le fil de section rectangulaire en cuivre nu ou émaillé guipé de fibres de verre avec polyester, imprégnées ou non de vernis ou de résine. Mots clé: fil de cuivre
Specifikacije za posebne vrste navijalnih žic - 0-8. del: Splošne zahteve - S poliestrskim steklenim vlaknom povita, s smolo ali posteklino impregnirana ali neimpregnirana, gola ali emajlirana pravokotna bakrena žica
Ta del standarda IEC 60317 določa splošne zahteve za bakreno žico, navito s poliestrski steklenimi vlakni, s smolo ali posteklino impregnirano ali neimpregnirano, golo ali emajlirano pravokotno bakreno žico. Obseg nazivnih dimenzij kondenzatorja je podan v ustrezni razpredelnici.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Specifikacije za posebne vrste navijalnih žic - 0-8. del: Splošne zahteve - S poliestrskim steklenim vlaknom povita, s smolo ali posteklino impregnirana ali neimpregnirana, gola ali emajlirana pravokotna bakrena žicaSpécifications pour types particuliers de fils de bobinage - Partie 0-8: Exigences générales - Fil de section rectangulaire en cuivre nu ou émaillé guipé de fibres de verre avec polyester, imprégnées ou non de vernis ou de résineSpecifications for particular types of winding wires - Part 0-8: General requirements - Polyester glass-fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire29.060.10ŽiceWiresICS:Ta slovenski standard je istoveten z:EN 60317-0-8:2012SIST EN 60317-0-8:2012en01-december-2012SIST EN 60317-0-8:2012SLOVENSKI
STANDARD
SIST EN 60317-0-8:2012
EUROPEAN STANDARD EN 60317-0-8 NORME EUROPÉENNE
EUROPÄISCHE NORM September 2012
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-0-8:2012 E
ICS 29.060.10
English version
Specifications for particular types of winding wires -
Part 0-8: General requirements -
Polyester glass fibre wound, resin or varnish impregnated
or not impregnated, bare or enamelled rectangular copper wire (IEC 60317-0-8:2012)
Spécifications pour types particuliers
de fils de bobinage -
Partie 0-8: Exigences générales -
Fil de section rectangulaire en cuivre
nu ou émaillé, guipé de fibres de verre avec polyester, imprégnées ou non
de vernis ou de résine (CEI 60317-0-8:2012)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten -
Teil-0-8: Allgemeine Anforderungen -
Flachdrähte aus Kupfer, blank oder lackisoliert, mit Polyesterglasgewebe umsponnen und mit Harz oder Lack imprägniert oder nicht imprägniert (IEC 60317-0-8:2012)
This European Standard was approved by CENELEC on 2012-08-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 60317-0-8:2012
EN 60317-0-8:2012 - 2 - Foreword The text of document 55/1324/FDIS, future edition 1 of IEC 60317-0-8, prepared by IEC/TC 55 "Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-0-8:2012. The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-05-16 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-08-16
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60317-0-8:2012 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60264 Series NOTE Harmonised as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonised as EN 60317 Series (not modified). IEC 60851 Series NOTE Harmonised as EN 60851 Series (not modified).
SIST EN 60317-0-8:2012
- 3 - EN 60317-0-8:2012 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60851 Series Winding wires - Test methods EN 60851 Series
ISO 3 1973 Preferred numbers - Series of preferred numbers - -
SIST EN 60317-0-8:2012
SIST EN 60317-0-8:2012
IEC 60317-0-8 Edition 1.0 2012-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires –
Part 0-8: General requirements – Polyester glass fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire
Spécifications pour types particuliers de fils de bobinage –
Partie 0-8: Exigences générales – Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre avec polyester, imprégnées ou non de vernis
ou de résine
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE T ICS 29.060.10 PRICE CODE CODE PRIX ISBN 978-2-83220-187-9
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé. SIST EN 60317-0-8:2012
– 2 – 60317-0-8 © IEC:2012 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope . 7 2 Normative references . 7 3 Terms, definitions and general notes on tests and appearance . 7 3.1 Terms and definitions . 7 3.2 General notes. 8 3.2.1 Methods of test . 8 3.2.2 Winding wire . 8 3.3 Appearance . 9 4 Dimensions . 9 4.1 Conductor dimensions . 9 4.2 Tolerance on conductor dimensions . 11 4.3 Rounding of corners . 11 4.4 Increase in dimensions due to the insulation . 11 4.5 Overall dimensions . 13 4.5.1 Nominal overall dimensions . 13 4.5.2 Minimum overall dimensions . 13 4.5.3 Maximum overall dimensions . 13 5 Electrical resistance . 13 6 Elongation . 13 7 Springiness . 13 8 Flexibility and adherence . 14 8.1 Mandrel winding test . 14 8.2 Adherence test . 14 8.2.1 Fibre covered bare wires . 14 8.2.2 Fibre covered enamelled wires . 14 9 Heat shock . 14 10 Cut-through . 14 11 Resistance to abrasion . 14 12 Resistance to solvents . 14 13 Breakdown voltage . 14 14 Continuity of insulation . 15 15 Temperature index . 15 16 Resistance to refrigerants . 15 17 Solderability . 15 18 Heat or solvent bonding . 15 19 Dielectric dissipation factor . 15 20 Resistance to transformer oil . 15 21 Loss of mass . 16 23 Pin hole test . 16 30 Packaging . 16 SIST EN 60317-0-8:2012
60317-0-8 © IEC:2012 – 3 –
Annex A (informative)
Nominal cross-sectional areas for preferred and intermediate sizes . 17 Bibliography . 24
Table 1 – Nominal cross-sectional areal of preferred sizes . 10 Table 2 – Conductor tolerances . 11 Table 3 – Corner radii . 11 Table 4 – Increase in dimensions . 12 Table 5 – Elongation . 13 Table 6 – Mandrel winding . 14 Table 7 – Breakdown voltage . 15 Table A.1 – Nominal cross-sectional areas (1 of 7) . 17
SIST EN 60317-0-8:2012
– 4 – 60317-0-8 © IEC:2012 INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
SPECIFICATIONS FOR PARTICULAR
TYPES OF WINDING WIRES –
Part 0-8: General requirements –
Polyester glass fibre wound, resin or varnish impregnated
or not impregnated, bare or enamelled rectangular copper wire
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-0-8 has been prepared by IEC technical committee 55: Winding wires. The text of this standard is based on the following documents: FDIS Report on voting 55/1324/FDIS 55/1337/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. SIST EN 60317-0-8:2012
60317-0-8 © IEC:2012 – 5 –
The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. A list of all the parts in the IEC 60317 series, published under the general title Specifications for particular types of winding wires can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be
• reconfirmed, • withdrawn, • replaced by a revised edition, or • amended.
SIST EN 60317-0-8:2012
– 6 – 60317-0-8 © IEC:2012 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires – Test methods (IEC 60851); 2) Specifications for particular types of winding wires (IEC 60317); 3) Packaging of winding wires (IEC 60264). SIST EN 60317-0-8:2012
60317-0-8 © IEC:2012 – 7 –
SPECIFICATIONS FOR PARTICULAR
TYPES OF WINDING WIRES –
Part 0-8: General requirements –
Polyester glass fibre wound, resin or varnish impregnated
or not impregnated, bare or enamelled rectangular copper wire
1 Scope This part of IEC 60317 specifies general requirements of polyester glass fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire. The range of nominal conductor dimensions is given in the relevant specification sheet. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60851 (all parts), Winding wires – Test methods ISO 3:1973, Preferred numbers – Series of preferred numbers 3 Terms, definitions and general notes on tests and appearance 3.1 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1
coating material which is deposited on a conductor or wire by a suitable means and then dried and/or cured 3.1.2
conductor bare metal after removal of the insulation 3.1.3
covering material which is wound, wrapped or braided around a bare or insulated conductor 3.1.4
crack opening in the insulation which exposes the conductor to view at the stated magnification 3.1.5
enamelled wire wire coated with an insulation of cured resin SIST EN 60317-0-8:2012
– 8 – 60317-0-8 © IEC:2012 3.1.6
grade range of thickness of the insulation of a wire 3.1.7
insulation coating or covering on the conductor with the specific function of withstanding voltage 3.1.8
nominal conductor dimension designation of the conductor size in accordance with IEC 60317 3.1.9
normal vision 20/20 vision, with corrective lenses, if necessary 3.1.10
winding wire wire used for winding a coil to provide a magnetic field 3.1.11
wire conductor coated or covered with an insulation 3.2 General notes 3.2.1 Methods of test All methods of test to be used for this standard are given in the IEC 60851 series. The clause numbers used in this standard are identical with the respective test numbers in the IEC 60851 series. In case of inconsistencies between the IEC 60851 series and this standard, IEC 60317-0-8 shall prevail. Where no specific range of nominal conductor dimensions is given for a test, the test applies to all nominal conductor dimensions covered by the specification sheet. Unless otherwise specified, all tests shall be carried out at a temperature from 15 °C to 40 °C and a relative humidity from 45 % to 75 %. Before measurements are made, the specimens shall be preconditioned under these atmospheric conditions for a time sufficient to allow the specimens to reach stability.
The wire to be tested shall be removed from the packaging in such a way that the wire will not be subjected to tension or unnecessary bends. Before each test, sufficient wire should be discarded to ensure that any damaged wire is not included in the test specimens. 3.2.2 Winding wire When reference is made to a winding wire according to a standard in the IEC 60317 series, the following information is included
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.