SIST EN 12808-3:2009
(Main)Grouts for tiles - Part 3: Determination of flexural and compressive strength
Grouts for tiles - Part 3: Determination of flexural and compressive strength
This European Standard applies to all ceramic tile grouts for internal and external tile installations on walls and floors.
This European Standard describes the test method to be used to determine the compressive and flexural strength of ceramic tile grouts.
This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles.
NOTE Ceramic tile grouts may also be used for other types of tiles (natural and agglomerated stones, etc. ), where these do not adversely affect the stones.
Mörtel und Klebstoffe für Fliesen und Platten — Teil 3: Bestimmung der Biege- und Druckfestigkeit
Diese Europäische Norm ist auf sämtliche Fugenmörtel für keramische Fliesen und Platten an Wand und Boden für innen und außen anwendbar.
Diese Europäische Norm beschreibt das Prüfverfahren zur Bestimmung der Druck und Biegefestigkeit von Fugenmörtel für keramische Fliesen und Platten.
Diese Europäische Norm enthält keine Anforderungen und keine Empfehlungen hinsichtlich der Planung und Verlegung von keramischen Fliesen/Platten.
ANMERKUNG Fugenmörtel für keramische Fliesen und Platten können auch für andere Arten von Fliesen und Platten verwendet werden (Natur , Betonwerksteine usw.), sofern diese die Steine nicht negativ beeinflussen.
Mortiers de joints pour carrelage - Partie 3: Détermination de la résistance à la flexion et à la compression
La présente Norme européenne s’applique à tous les mortiers utilisés pour le jointoiement de carrelages céramiques sur les murs et au sol, à l’intérieur et à l’extérieur.
La présente Norme européenne spécifie la méthode d’essai qui doit être utilisée pour déterminer la résistance à la flexion et à la compression.
La présente Norme européenne ne contient pas de spécifications, ni de recommandations pour la conception, la pose et le jointoiement des carrelages en céramique.
NOTE Les mortiers de joints peuvent être également utilisés pour d’autres types de carrelage (pierre naturelle ou agglomérée, etc.) s'ils sont compatibles.
Lepila in fugirne malte za ploščice - 3. del: Ugotavljanje upogibne in tlačne trdnosti
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Mörtel und Klebstoffe für Fliesen und Platten — Teil 3: Bestimmung der Biege- und DruckfestigkeitMortiers de joints pour carrelage - Partie 3: Détermination de la résistance à la flexion et à la compressionGrouts for tiles - Part 3: Determination of flexural and compressive strength91.100.23Ceramic tiles91.100.10Cement. Mavec. Apno. MaltaCement. Gypsum. Lime. Mortar83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 12808-3:2008SIST EN 12808-3:2009en,fr,de01-marec-2009SIST EN 12808-3:2009SLOVENSKI
STANDARDSIST EN 12808-3:20021DGRPHãþD
SIST EN 12808-3:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12808-3October 2008ICS 83.180; 91.100.10Supersedes EN 12808-3:2001
English VersionGrouts for tiles - Part 3: Determination of flexural andcompressive strengthMortiers de joints pour carrelage - Partie 3: Déterminationde la résistance à la flexion et à la compressionMörtel und Klebstoffe für Fliesen und Platten - Teil 3:Bestimmung der Biege- und DruckfestigkeitThis European Standard was approved by CEN on 29 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12808-3:2008: ESIST EN 12808-3:2009
EN 12808-3:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Sampling.4 4 Test conditions.4 5 Test materials.4 6 Apparatus.4 7 Procedure.5 7.1 Mixing of grouts.5 7.2 Preparation of test specimens.5 7.3 Flexural strength under standard conditions.6 7.4 Compressive strength under standard conditions.6 7.5 Flexural and compressive strength after freeze-thaw cycles.6 8 Evaluation of results.6 8.1 Flexural strength.6 8.2 Compressive strength.7 9 Test report.7 Bibliography.9
SIST EN 12808-3:2009
EN 12808-3:2008 (E) 3 Foreword This document (EN 12808-3:2008) has been prepared by Technical Committee CEN/TC 67 “Ceramic tiles”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by April 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12808-3:2001. This document is one of a series of European Standards for ceramic tile adhesives including: EN 1308, Adhesives for tiles - Determination of slip EN 1323, Adhesives for tiles - Concrete slabs for tests EN 1324, Adhesives for tiles - Determination of shear adhesion strength of dispersion adhesives EN 1346, Adhesives for tiles - Determination of open time EN 1347, Adhesives for tiles - Determination of wetting capability EN 1348, Adhesives for tiles - Determination of tensile adhesion strength for cementitious adhesives EN 12002, Adhesives for tiles - Determination of transverse deformation for cementitious adhesives and grouts EN 12003, Adhesive for tiles - Determination of shear adhesion strength of reaction resin adhesives EN 12004, Adhesives for tiles – Requirements, evaluation of conformity, classification and designation EN 12808-1, Grouts for tiles – Part 1: Determination of chemical resistance of reaction resin mortars EN 12808-2, Grouts for tiles – Part 2: Determination of resistance to abrasion EN 12808-3, Grouts for tiles – Part 3: Determination of flexural and compressive strength EN 12808-4, Grouts for tiles – Part 4: Determination of shrinkage EN 12808-5, Grouts for tiles – Part 5: Determination of water absorption According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 12808-3:2009
EN 12808-3:2008 (E) 4
1 Scope This European Standard applies to all ceramic tile grout
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Grouts for tiles - Part 3: Determination of flexural and compressive strengthMortiers de joints pour carrelage - Partie 3: Détermination de la résistance à la flexion et à la compressionMörtel und Klebstoffe für Fliesen und Platten — Teil 3: Bestimmung der Biege- und DruckfestigkeitTa slovenski standard je istoveten z:prEN 12808-3kSIST prEN 12808-3:2008en,fr,de91.100.1083.180ICS:SLOVENSKI
STANDARDkSIST prEN 12808-3:200801-maj-2008
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMFINAL DRAFTprEN 12808-3February 2008ICS 83.180; 91.100.10Will supersede EN 12808-3:2001
English VersionGrouts for tiles - Part 3: Determination of flexural andcompressive strengthMortiers de joints pour carrelage - Partie 3: Déterminationde la résistance à la flexion et à la compressionThis draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the TechnicalCommittee CEN/TC 67.If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations whichstipulate the conditions for giving this European Standard the status of a national standard without any alteration.This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other languagemade by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has thesame status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice andshall not be referred to as a European Standard.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. prEN 12808-3:2008: E
prEN 12808-3:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Sampling.4 4 Test conditions.4 5 Test materials.4 6 Apparatus.4 7 Procedure.5 7.1 Mixing of grouts.5 7.2 Preparation of test specimens.5 7.3 Flexural strength under standard conditions.6 7.4 Compressive strength under standard conditions.6 7.5 Flexural and compressive strength after freeze-thaw cycles.6 8 Evaluation of results.6 8.1 Flexural strength.6 8.2 Compressive strength.7 9 Test report.7 Bibliography.9
prEN 12808-3:2008 (E) 3 Foreword This document (prEN 12808-3:2008) has been prepared by Technical Committee CEN/TC 67 “Ceramic tiles”, the secretariat of which is held by UNI. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 12808-3:2001. This document is one of a series of European Standards for ceramic tile adhesives including: EN 12808-1, Grouts for tiles – Part 1: Determination of chemical resistance of reaction resin mortars EN 12808-2, Grouts for tiles – Part 2: Determination of resistance to abrasion EN 12808-3, Grouts for tiles – Part 3: Determination of flexural and compressive strength EN 12808-5, Grouts for tiles – Part 5: Water absorption
prEN 12808-3:2008 (E) 4
1 Scope This European Standard applies to all ceramic tile grouts for internal and external tile installations on walls and floors. This European Standard describes the test method to be used to determine the compressive and flexural strength of ceramic tile grouts. This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles. NOTE Ceramic tile grouts may also be used for other types of tiles (natural and agglomerated stones, etc. ), where these do not adversely affect the stones. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 196-1:2005, Me
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.