SIST EN 60317-52:2014
(Main)Specifications for particular types of winding wires - Part 52: Aromatic polyamide (aramid) tape wrapped round copper wire, temperature index 220
Specifications for particular types of winding wires - Part 52: Aromatic polyamide (aramid) tape wrapped round copper wire, temperature index 220
EN IEC 60317-52 specifies requirements for tape wrapped round copper winding wire of temperature index 220. The insulation consists of one or more wrappings of aromatic polyamide (aramid) tape of various thicknesses. The range of nominal conductor diameters covered by this standard is: - 1,600 mm up to and including 5,000 mm; - the nominal conductor diameters are given in Table 1.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 52: Runddrähte aus Kupfer, umwickelt mit Band aus aromatischen Polyamiden, Temperaturindex 220
Spécifications pour types particuliers de fils de bobinage -- Partie 52: Fil de section circulaire en cuivre enveloppé avec un ruban polyamide aromatique (aramide), d'indice de température 220
L'IEC 60317-52:2014 spécifie les exigences relatives au fil de bobinage de section circulaire en cuivre enveloppé avec un ruban, d'indice de température 220. L'isolant est constitué d'une ou de plusieurs enveloppes constituées d'un ruban polyamide aromatique (aramide) d'épaisseurs variées. La gamme des diamètres nominaux des conducteurs couverte par la présente norme est: - 1,600 mm jusques et y compris 5,000 mm; - les diamètres nominaux des conducteurs sont indiqués dans le Tableau 1. Cette deuxième édition annule et remplace la première édition parue en 1999. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - un nouveau 3.2.2 contenant des notes générales sur le fil de bobinage intégrées auparavant au domaine d'application; - un nouveau 3.3 contenant des exigences relatives à l'aspect; - une modification de l'Article 15 en vue de supprimer la note relative aux révisions de l'IEC 60172; - un nouvel Article 23, Détection des microfissures en immersion. Mots clés: fil de bobinage de section circulaire en cuivre enveloppé avec un ruban, d'indice de température 220, ruban polyamide aromatique (aramide)
Specifikacije za posebne vrste navijalnih žic - 52. del: Aromatski poliamidni (aramidni) trak, ovit okoli okrogle bakrene žice, toplotni indeks 220
Standard EN IEC 60317-52 določa zahteve za s trakom ovito okroglo bakreno navijalno žico s toplotnim indeksom 220. Izolacijo sestavlja en ali več ovojev aromatskega poliamidnega (aramidnega) traka različnih debelin. Razpon nazivnega premera prevodnika, ki ga zajema ta standard, je: – 1 600 mm do in vključno s 5000 mm; – nazivni premeri prevodnika so navedeni v tabeli 1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60317-52:2014
01-september-2014
1DGRPHãþD
SIST EN 60317-52:2001
Specifikacije za posebne vrste navijalnih žic - 52. del: Aromatski poliamidni
(aramidni) trak, ovit okoli okrogle bakrene žice, toplotni indeks 220
Specifications for particular types of winding wires - Part 52: Aromatic polyamide
(aramid) tape wrapped round copper wire, temperature index 220
Spécifications pour types particuliers de fils de bobinage -- Partie 52: Fil de section
circulaire en cuivre enveloppé avec un ruban polyamide aromatique (aramide), d'indice
de température 220
Ta slovenski standard je istoveten z: EN 60317-52:2014
ICS:
29.060.10 Žice Wires
SIST EN 60317-52:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60317-52:2014
---------------------- Page: 2 ----------------------
SIST EN 60317-52:2014
EUROPEAN STANDARD EN 60317-52
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2014
ICS 29.060.10 Supersedes EN 60317-52:1999
English Version
Specifications for particular types of winding wires - Part 52:
Aromatic polyamide (aramid) tape wrapped round copper wire,
temperature index 220
(IEC 60317-52:2014)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 52: Fil de section circulaire en cuivre enveloppé avec Wickeldrähten - Teil 52: Runddrähte aus Kupfer, umwickelt
un ruban polyamide aromatique (aramide), d'indice de mit Band aus aromatischen Polyamiden, Temperaturindex
température 220 220
(CEI 60317-52:2014) (IEC 60317-52:2014)
This European Standard was approved by CENELEC on 2014-03-21. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60317-52:2014 E
---------------------- Page: 3 ----------------------
SIST EN 60317-52:2014
EN 60317-52:2014 - 2 -
Foreword
The text of document 55/1395/CDV, future edition 2 of IEC 60317-52, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60317-52:2014.
The following dates are fixed:
(dop) 2014-12-21
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2017-03-21
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60317-52:1999.
EN 60317-52:2014 includes the following significant technical changes with respect to
EN 60317-52:1999:
– new 3.2.2 containing general notes on winding wire, formerly a part of the scope;
– new 3.3, containing requirements for appearance;
– modification to Clause 15 to delete the note on revisions to IEC 60172;
– new Clause 23, Pin hole test.
The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to
reserve space for possible future wire requirements prior to those for wire packaging.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60317-52:2014 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified).
IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified).
---------------------- Page: 4 ----------------------
SIST EN 60317-52:2014
- 3 - EN 60317-52:2014
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
ISO 3 1973 Preferred numbers - Series of preferred - -
numbers
IEC 60172 Test procedure for the determination of the EN 60172
temperature index of enamelled winding wires
IEC 60819-3-3 2011 Non-cellulosic papers for electrical purposes - EN 60819-3-3 2011
Part 3: Specifications for individual materials -
Sheet 3: Unfilled aramid (aromatic polyamide)
papers
IEC 60851 (Series) Winding wires - Test methods EN 60851-6 (Series)
---------------------- Page: 5 ----------------------
SIST EN 60317-52:2014
---------------------- Page: 6 ----------------------
SIST EN 60317-52:2014
IEC 60317-52
®
Edition 2.0 2014-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 52: Aromatic polyamide (aramid) tape wrapped round copper wire,
temperature index 220
Spécifications pour types particuliers de fils de bobinage –
Partie 52: Fil de section circulaire en cuivre enveloppé avec un ruban polyamide
aromatique (aramide), d’indice de température 220
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX Q
ICS 29.060.10 ISBN 978-2-8322-1414-5
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60317-52:2014
– 2 – IEC 60317-52:2014 © IEC 2014
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, general notes and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes . 8
3.2.1 Methods of test . 8
3.2.2 Winding wire . 8
3.3 Appearance . 8
4 Dimensions . 9
4.1 Conductor diameter . 9
4.2 Out of roundness of conductor. 9
4.3 Minimum increase in diameter due to insulation . 9
4.4 Maximum overall diameter . 10
5 Electrical resistance . 10
6 Elongation . 11
7 Springiness . 11
8 Flexibility and adherence . 11
9 Heat shock . 11
10 Cut-through . 11
11 Resistance to abrasion . 11
12 Resistance to solvents . 11
13 Breakdown voltage. 11
14 Continuity of insulation . 11
15 Temperature index . 12
16 Resistance to refrigerants . 12
17 Solderability . 12
18 Heat or solvent bonding . 12
19 Dielectric dissipation factor . 12
20 Resistance to hydrolysis and to transformer oil . 12
21 Loss of mass . 12
23 Pin hole test . 12
30 Packaging . 12
Annex A (informative) Nominal conductor diameters for intermediate sizes (R40) . 14
Annex B (informative) Example of tape wrapped wire . 15
Annex C (informative) Resistance. 16
Bibliography . 17
Figure B.1 – Illustrations of overlap . 15
---------------------- Page: 8 ----------------------
SIST EN 60317-52:2014
IEC 60317-52:2014 © IEC 2014 – 3 –
Table 1 – Conductor diameters . 9
Table 2 – Elongation requirements . 11
Table A.1 – Conductor diameters (R40) . 14
Table C.1 – Nominal resistance . 16
---------------------- Page: 9 ----------------------
SIST EN 60317-52:2014
– 4 – IEC 60317-52:2014 © IEC 2014
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR
TYPES OF WINDING WIRES –
Part 52: Aromatic polyamide (aramid) tape wrapped
round copper wire, temperature index 220
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.