Environmental Engineering (EE) - Metrics and measurement method for energy efficiency of wireless access network equipment - Part 1: Power consumption - static measurement method

The present document version covers base stations with the following radio access technologies:
• GSM.
• WCDMA.
• LTE.
• NR.
The methodology described in the present document is to measure base station static power consumption and RF output
power. Within the present document it is referred to as static measurements.
The results based on "static" measurements provide power and energy consumption figures for BS under static load.
Energy consumption of terminal (end-user) equipment is outside the scope of the present document.
The scope of the present document is not to define target values for the BS power and energy consumption.
The results should only be used to assess and compare the power and energy consumption of complete base stations.
Wide Area Base Stations and Medium Range Base Stations (as defined in ETSI TS 125 104 [2], ETSI TS 136 104 [12],
and ETSI TS 138 104 [15]) are covered in the present document.

Okoljski inženiring (EE) - Metrika in metoda merjenja energijske učinkovitosti opreme brezžičnega dostopovnega omrežja - 1. del: Poraba energije - Statična merilna metoda

Ta različica dokumenta zajema bazne postaje z naslednjimi tehnologijami radijskega dostopa:
• GSM,
• WCDMA,
• LTE,
• NR.
Metodologija, opisana v tem dokumentu, se uporablja za merjenje porabe statične energije bazne postaje in izhodne moči RF. V tem dokumentu jo imenujemo statične meritve.
Rezultati na podlagi »statičnih« meritev zagotavljajo številske vrednosti moči in porabe energije bazne postaje pri statični obremenitvi.
Poraba energije terminalske opreme (opreme končnih uporabnikov) ne spada na področje uporabe tega dokumenta.
Namen tega dokumenta ni določitev ciljnih vrednosti za moč in porabo energije baznih postaj.
Rezultate naj bi uporabljali le za ocenjevanje in primerjanje moči ter porabe energije celotnih baznih postaj.
Ta dokument zajema prostrane bazne postaje in bazne postaje srednjega dosega (kot so opredeljene v standardih ETSI TS 125-104 [2], ETSI TS 136-104 [12] in ETSI TS 138-104 [15]).

General Information

Status
Published
Publication Date
22-Sep-2024
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
17-Sep-2024
Due Date
22-Nov-2024
Completion Date
23-Sep-2024

Buy Standard

Standard
ETSI ES 202 706-1 V1.8.0 (2024-07) - Environmental Engineering (EE); Metrics and measurement method for energy efficiency of wireless access network equipment; Part 1: Power consumption - static measurement method
English language
50 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI ES 202 706-1 V1.8.1 (2024-09) - Environmental Engineering (EE); Metrics and measurement method for energy efficiency of wireless access network equipment; Part 1: Power consumption - static measurement method
English language
50 pages
sale 15% off
Preview
sale 15% off
Preview
Standardization document
ES 202 706-1 V1.8.1:2024 - BARVE
English language
50 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


Final draft ETSI ES 202 706-1 V1.8.0 (2024-07)

ETSI STANDARD
Environmental Engineering (EE);
Metrics and measurement method for energy efficiency
of wireless access network equipment;
Part 1: Power consumption - static measurement method

2 Final draft ETSI ES 202 706-1 V1.8.0 (2024-07)

Reference
RES/EE-EEPS70
Keywords
energy efficiency, GSM, LTE, NR, power
measurement, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
https://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
No representation or warranty is made that this deliverable is technically accurate or sufficient or conforms to any law
ntation or warranty is made of merchantability or fitness
and/or governmental rule and/or regulation and further, no represe
for any particular purpose or against infringement of intellectual property rights.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2024.
All rights reserved.
ETSI
3 Final draft ETSI ES 202 706-1 V1.8.0 (2024-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Assessment method . 12
5 Reference configurations and Measurement conditions . 12
5.0 Introduction . 12
5.1 Reference configurations . 12
5.2 Measurement and test equipment requirements . 14
5.2.0 Introduction. 14
5.2.1 BS Configuration . 15
5.2.2 RF output (transmit) power/signal . 15
5.2.3 Environmental conditions . 15
5.2.4 Power supply . 16
6 Static Power Measurement . 16
6.0 Introduction . 16
6.1 Measurement methods . 16
6.1.0 Introduction. 16
6.1.1 Test setup for conducted power measurement . 17
6.1.2 Test setup for radiated power measurement. 18
6.1.3 Power measurement procedure . 19
6.1.4 Power measurement in RF sharing mode . 19
6.1.5 Power measurement of multi-band configurations . 20
6.1.5.0 Introduction . 20
6.1.5.1 Configuration of a multi-band BS . 20
6.1.5.2 Specific configurations for dual band GSM . 20
6.1.5.3 Specific configurations for dual band LTE (LTE-A) . 20
6.1.5.4 Specific configurations for dual band and dual technology . 21
6.2 Uncertainty . 21
7 Calculation results . 21
7.1 Load distribution profile . 21
7.2 Integrated base station . 21
7.2.0 Introduction. 21
7.2.1 Calculation of average power consumption of integrated BS . 22
7.2.2 Calculation of daily energy consumption of integrated BS . 22
7.3 Distributed base station . 22
7.3.0 Introduction. 22
7.3.1 Calculation of average power consumption of distributed BS . 22
7.3.2 Calculation of daily energy consumption of distributed BS . 23
8 Measurement report . 23
Annex A (normative): Test Reports . 24
A.1 General information to be reported . 24
ETSI
4 Final draft ETSI ES 202 706-1 V1.8.0 (2024-07)
A.2 Static measurement report . 25
Annex B (normative): Reference parameters for GSM/EDGE system . 27
Annex C (normative): Reference parameters for WCDMA/HSDPA system . 29
Annex D (normative): Reference parameters for LTE system . 30
Annex E (normative): Reference parameters for NR system . 34
Annex F (normative): Reference parameters for multi-standard system. 36
Annex G (normative): Uncertainty assessment . 38
G.0 Introduction . 38
G.1 General requirements . 38
G.2 Components contributing to uncertainty . 39
G.2.0 Introduction . 39
G.2.1 Contribution of the measurement system . 39
G.2.1.1 Measurement equipment . 39
G.2.1.2 Attenuators, cables . 39
G.2.2 Contribution of physical parameters. 39
G.2.2.1 Impact of environmental parameters. 39
G.2.3 Variance of device under test . 39
G.3 Uncertainty assessment . 40
G.3.1 Combined and expanded uncertainties . 40
G.3.2 Cross correlation of uncertainty factors . 40
G.3.3 Maximum expanded uncertainty . 40
Annex H (informative): Example assessment .
...


ETSI STANDARD
Environmental Engineering (EE);
Metrics and measurement method for energy efficiency
of wireless access network equipment;
Part 1: Power consumption - static measurement method

2 ETSI ES 202 706-1 V1.8.1 (2024-09)

Reference
RES/EE-EEPS70
Keywords
energy efficiency, GSM, LTE, NR,
power measurement, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from the
ETSI Search & Browse Standards application.
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format on ETSI deliver.
Users should be aware that the present document may be revised or have its status changed,
this information is available in the Milestones listing.
If you find errors in the present document, please send your comments to
the relevant service listed under Committee Support Staff.
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure (CVD) program.
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
No representation or warranty is made that this deliverable is technically accurate or sufficient or conforms to any law
and/or governmental rule and/or regulation and further, no representation or warranty is made of merchantability or fitness
for any particular purpose or against infringement of intellectual property rights.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2024.
All rights reserved.
ETSI
3 ETSI ES 202 706-1 V1.8.1 (2024-09)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Assessment method . 12
5 Reference configurations and Measurement conditions . 12
5.0 Introduction . 12
5.1 Reference configurations . 12
5.2 Measurement and test equipment requirements . 14
5.2.0 Introduction. 14
5.2.1 BS Configuration . 15
5.2.2 RF output (transmit) power/signal . 15
5.2.3 Environmental conditions . 15
5.2.4 Power supply . 16
6 Static Power Measurement . 16
6.0 Introduction . 16
6.1 Measurement methods . 16
6.1.0 Introduction. 16
6.1.1 Test setup for conducted power measurement . 17
6.1.2 Test setup for radiated power measurement. 18
6.1.3 Power measurement procedure . 19
6.1.4 Power measurement in RF sharing mode . 19
6.1.5 Power measurement of multi-band configurations . 20
6.1.5.0 Introduction . 20
6.1.5.1 Configuration of a multi-band BS . 20
6.1.5.2 Specific configurations for dual band GSM . 20
6.1.5.3 Specific configurations for dual band LTE (LTE-A) . 20
6.1.5.4 Specific configurations for dual band and dual technology . 21
6.2 Uncertainty . 21
7 Calculation results . 21
7.1 Load distribution profile . 21
7.2 Integrated base station . 21
7.2.0 Introduction. 21
7.2.1 Calculation of average power consumption of integrated BS . 22
7.2.2 Calculation of daily energy consumption of integrated BS . 22
7.3 Distributed base station . 22
7.3.0 Introduction. 22
7.3.1 Calculation of average power consumption of distributed BS . 22
7.3.2 Calculation of daily energy consumption of distributed BS . 23
8 Measurement report . 23
Annex A (normative): Test Reports . 24
A.1 General information to be reported . 24
ETSI
4 ETSI ES 202 706-1 V1.8.1 (2024-09)
A.2 Static measurement report . 25
Annex B (normative): Reference parameters for GSM/EDGE system . 27
Annex C (normative): Reference parameters for WCDMA/HSDPA system . 29
Annex D (normative): Reference parameters for LTE system . 30
Annex E (normative): Reference parameters for NR system . 34
Annex F (normative): Reference parameters for multi-standard system. 36
Annex G (normative): Uncertainty assessment . 38
G.0 Introduction . 38
G.1 General requirements . 38
G.2 Components contributing to uncertainty . 39
G.2.0 Introduction . 39
G.2.1 Contribution of the measurement system . 39
G.2.1.1 Measurement equipment . 39
G.2.1.2 Attenuators, cables . 39
G.2.2 Contribution of physical parameters. 39
G.2.2.1 Impact of environmental parameters. 39
G.2.3 Variance of device under test . 39
G.3 Uncertainty assessment . 40
G.3.1 Combined and expanded uncertainties . 40
G.3.2 Cross correlation of uncertainty factors . 40
G.3.3 Maximum expanded uncertainty . 40
Annex H (informative): Example assessment . 41
Annex I (informative): Interpolation method . 43
Annex J (informative): Load placement examples .
...


SLOVENSKI STANDARD
01-november-2024
Okoljski inženiring (EE) - Metrika in metoda merjenja energijske učinkovitosti
opreme brezžičnega dostopovnega omrežja - 1. del: Poraba energije - Statična
merilna metoda
Environmental Engineering (EE) - Metrics and measurement method for energy
efficiency of wireless access network equipment - Part 1: Power consumption - static
measurement method
Ta slovenski standard je istoveten z: ETSI ES 202 706-1 V1.8.1 (2024-09)
ICS:
19.040 Preskušanje v zvezi z Environmental testing
okoljem
27.015 Energijska učinkovitost. Energy efficiency. Energy
Ohranjanje energije na conservation in general
splošno
33.070.50 Globalni sistem za mobilno Global System for Mobile
telekomunikacijo (GSM) Communication (GSM)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

ETSI STANDARD
Environmental Engineering (EE);
Metrics and measurement method for energy efficiency
of wireless access network equipment;
Part 1: Power consumption - static measurement method

2 ETSI ES 202 706-1 V1.8.1 (2024-09)

Reference
RES/EE-EEPS70
Keywords
energy efficiency, GSM, LTE, NR,
power measurement, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from the
ETSI Search & Browse Standards application.
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format on ETSI deliver.
Users should be aware that the present document may be revised or have its status changed,
this information is available in the Milestones listing.
If you find errors in the present document, please send your comments to
the relevant service listed under Committee Support Staff.
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure (CVD) program.
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
No representation or warranty is made that this deliverable is technically accurate or sufficient or conforms to any law
and/or governmental rule and/or regulation and further, no representation or warranty is made of merchantability or fitness
for any particular purpose or against infringement of intellectual property rights.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2024.
All rights reserved.
ETSI
3 ETSI ES 202 706-1 V1.8.1 (2024-09)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Assessment method . 12
5 Reference configurations and Measurement conditions . 12
5.0 Introduction . 12
5.1 Reference configurations . 12
5.2 Measurement and test equipment requirements . 14
5.2.0 Introduction. 14
5.2.1 BS Configuration . 15
5.2.2 RF output (transmit) power/signal . 15
5.2.3 Environmental conditions . 15
5.2.4 Power supply . 16
6 Static Power Measurement . 16
6.0 Introduction . 16
6.1 Measurement methods . 16
6.1.0 Introduction. 16
6.1.1 Test setup for conducted power measurement . 17
6.1.2 Test setup for radiated power measurement. 18
6.1.3 Power measurement procedure . 19
6.1.4 Power measurement in RF sharing mode . 19
6.1.5 Power measurement of multi-band configurations . 20
6.1.5.0 Introduction . 20
6.1.5.1 Configuration of a multi-band BS . 20
6.1.5.2 Specific configurations for dual band GSM . 20
6.1.5.3 Specific configurations for dual band LTE (LTE-A) . 20
6.1.5.4 Specific configurations for dual band and dual technology . 21
6.2 Uncertainty . 21
7 Calculation results . 21
7.1 Load distribution profile . 21
7.2 Integrated base station . 21
7.2.0 Introduction. 21
7.2.1 Calculation of average power consumption of integrated BS . 22
7.2.2 Calculation of daily energy consumption of integrated BS . 22
7.3 Distributed base station . 22
7.3.0 Introduction. 22
7.3.1 Calculation of average power consumption of distributed BS . 22
7.3.2 Calculation of daily energy consumption of distributed BS . 23
8 Measurement report . 23
Annex A (normative): Test Reports . 24
A.1 General information to be reported . 24
ETSI
4 ETSI ES 202 706-1 V1.8.1 (2024-09)
A.2 Static measurement report . 25
Annex B (normative): Reference parameters for GSM/EDGE system . 27
Annex C (normative): Reference parameters for WCDMA/HSDPA system . 29
Annex D (normative): Reference parameters for LTE system . 30
Annex E (normative): Reference parameters for NR system . 34
Annex F (normative): Reference parameters for multi-standard system. 36
Annex G (normative): Uncertainty assessment . 38
G.0 Introduction . 38
G.1 General requirements . 38
G.2 Components contributing to uncertainty . 39
G.2.0 Introduction . 39
G.2.1 Contribution of the measurement system . 39
G.2.1.1 Measurement equipment . 39
G.2.1.2 Attenuators, cables . 39
G.2.2 Contribution of physical parameters. 39
G.2.2.1 Impact of environmental parameters.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.