SIST EN ISO 11403-2:2000

Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:1995)

Kunststoffe - Ermittlung und Darstellung vergleichbarer Vielpunktkennwerte - Teil 2: Thermische und Verarbeitungseigenschaften (ISO 11403-2:1995)

Dieser Teil der ISO 11403 legt folgende Prüfverfahren für die Ermittlung und Darstellung von Vielpunktkennwerten für folgende thermische und Verarbeitungseigenschaften von Kunststoffen fest: Enthalpie-Temperatur- Diagramm; Linearausdehnung-Temperatur-Diagramm; Schmelz-Scherungs-Viskosität.

Plastiques - Acquisition et présentation de données multiples comparables - Partie 2: Propriétés thermiques et caractéristiques relatives a la mise en oeuvre (ISO 11403-2:1995)

Polimerni materiali - Predstavitev primerljivih podatkov, pridobljenih v različnih razmerah - 2. del: Termične in predelavne lastnosti

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-2000
• Withdrawal Date: 30-Sep-2004
• ICS: 83.080.01 - Plastics in general
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 01-Oct-2004
• Due Date: 01-Oct-2004
• Completion Date: 01-Oct-2004
• Ref Project: EN ISO 11403-2:1999 - Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:1995)

Relations

• Replaced By: SIST EN ISO 11403-2:2004 - Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2004)
• Effective Date: 01-Oct-2004

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11403-2:2000
01-maj-2000
3ROLPHUQLPDWHULDOL3UHGVWDYLWHYSULPHUOMLYLKSRGDWNRYSULGREOMHQLKYUD]OLþQLK
UD]PHUDKGHO7HUPLþQHLQSUHGHODYQHODVWQRVWL
Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal
and processing properties (ISO 11403-2:1995)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Vielpunktkennwerte - Teil 2:
Thermische und Verarbeitungseigenschaften (ISO 11403-2:1995)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 2:
Propriétés thermiques et caractéristiques relatives a la mise en oeuvre (ISO 11403-
2:1995)
Ta slovenski standard je istoveten z: EN ISO 11403-2:1999
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11403-2:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11403-2:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 11403-2:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 11403-2:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 11403-2:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 11403-2:2000

---------------------- Page: 6 ----------------------

SIST EN ISO 11403-2:2000
INTERNATIONAL ISO
STANDARD 11403-2
First edition
1995-11-01
Plastics - Acquisition and presentation of
comparable multipoint data -
Part 2:
Thermal and processing properties
- Acquisition et pr&en ta tion de donnees multiples
Plas tiques
comparables -
Partie 2: Propri&& thermiques et caract6ristiques relatives 2 Ia mise en
euvre
giij
-
- -
-
-
-
iS0~ -
i-XE
Reference number
ISO 114032 1995(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 11403-2:2000
ISO 11403=2:1995(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 11403-2 was prepared by Technical Committee
lSO/TC 61, Plastics, Subcommittee SC 2, Mechanical properties.
ISO 11403 consists of the following Parts, under the general title
Plas tics - Acquisition and presentation of comparable multipoin t da ta:
- Part 7: Mechanical properties
- Part 2: Thermal and processing properties
- Part 3: Environmental influences on properties
Annex A of this part of ISO 11403 is for information only.
0 ISO 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronie or mechanical, including photocopying and
microfilm, without Permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-l 211 Geneve 20 l Switzerland
Printed in Switzerland

---------------------- Page: 8 ----------------------

SIST EN ISO 11403-2:2000
0 ISO ISO 11403-2:1995(E)
Introduction
This International Standard has been prepared because users of plastics
find sometimes that available data cannot be used readily to compare the
properties of similar materials, especially when the data have been sup-
plied by different sources. Even when the same Standard tests have been
used, they often allow the adoption of a wide range of alternative test
conditions, and the data obtained are not necessarily comparable. The
purpose of this International Standard is to identify specific methods and
conditions of test to be used for the acquisition and presentation of data
in Order that valid comparisons between materials tan be made.
ISO 10350 is concerned with Single-Point data. Such data represent the
most basic method for characterizing materials and are useful for the initial
stages of material selection. The present International Standard identifies
test conditions and procedures for the measurement and presentation of
a more substantial quantity of data. Esch property here is characterized
by multipoint data which demonstrate how that property depends upon
important variables such as time, temperature and environmental effects.
Additional properties are also considered in this Standard. These data
therefore enable more discriminating decisions to be made regarding a
material ’s suitability for a particular application. Some data are also con-
sidered adequate for undertaking predictions of Performance in Service
and of Optimum processing conditions for moulding a component, al-
though it should be recognized that, for purposes of design, additional data
will often be needed. One reason for this is that some properties are
strongly dependent upon the physical structure of the material. The test
procedures referred to in this Standard employ, where possible, the
multipurpose tensile bar, and the polymer structure in this test specimen
may be significantly different from that in specific regions of a moulded
component. Under these circumstances, therefore, the data will not be
suitable for accurate design calculations for product Performance. The
material supplier should be consulted for specific information on the ap-
plicability of data.
ISO 10350 and the various Parts of this International Standard together
define the means for acquiring and presenting a core set of comparable
data for use in material selection. Use of these Standards should result in
a rationalization of effort and a reduction of tost associated with Provision
of these data. Furthermore, reference to these Standards will simplify the
development of data models for the computerized storage and exchange
of data concerning material properties.
Where appropriate, values for test variables have been specified by this
Standard. For some tests however, owing to the wide range of conditions
over which different plastics perform, the Standard gives guidance in the
selection of certain test conditions so that they cover the operating range
for that polymer. Because, in general, the properties and Performance
specifications for different polymers differ widely, there is no Obligation to
generate data under all the test conditions specified in this Standard.
. . .
Ill

---------------------- Page: 9 ----------------------

SIST EN ISO 11403-2:2000
ISO 11403=2:1995(E) Q ISO
Data on a wide range of properties are needed to enable plastics to be
selected and used in the large variety of applications to which they are
suited. ISO Standards describe experimental procedures which are suit-
able for the acquisition of relevant information on many of these proper-
ties. For other properties, however, ISO Standards either do not exist or
exhibit shortcomings that complicate their use at present for the gener-
ation of comparable data (sec annex A). The Standard has therefore been
divided into Parts so that each patt tan be developed independently. In this
way, additional properties tan be inc!uded as new or revised Standards
become available.

---------------------- Page: 10 ----------------------

SIST EN ISO 11403-2:2000
ISO 11403=2:1995(E)
INTERNATIONAL STANDARD 0 ISO
Plastics - Acquisition and presentation of comparable
multipoint data -
Part 2:
Thermal and processing properties
ISO 294: 1995, Plastics - Injection moulding of test
1 Scope
specimens o f thermoplas tic ma terials.
This part of ISO 11403 specifies test procedures for
- Compression moulding of
ISO 295:1991, Plastics
the acquisition and presentation of multipoint data on
test specimens of thermosetting materials.
the following thermal and processing properties of
plastics:
- Preparation of test speci-
ISO 2818:1994, Plastics
mens by machining.
enthaIpy/temperature curve;
linear-expansion/temperature curve;
ISO 3167: 1993, Plastics - Multipurpose test speci-
mens.
melt shear viscosity.
ISO 10724: 1994, Plastics - Thermosetting moulding
ma terials - Injection moulding of multipurpose test
2 Normative references
specimens.
The following Standards contain provisions which,
ISO 11403-1:1994, Plastics - Acquisition and pres-
through reference in this text, constitute provisions
entation of comparable multipoin t data - Part 1.0
of this part of ISO 11403. At the time of publication,
Mechanical properties.
the editions indicated were valid. All Standards are
subject to revision, and Parties to agreements based
ISO 11443:1995, Plastics - Determination of the
on this part of ISO 11403 are encouraged to investi-
fluidity of plastics using capillary and slit-die
gate the possibility of applying the most recent edi-
rheome ters.
tions of the Standards indicated below. Members of
IEC and ISO maintain registers of currently valid
ASTM E 831-93, Test method for linear thermal ex-
International Standards.
pansion of solid materials by thermomechanical
analysis.
ISO 291 :1977, Plastics - Standard atmospheres for
conditioning and testing.
ASTM E 968-83(1993), Practice for heat flow cali-
bration of differential scanning calorime ters.
ISO 293: 1986, Plastics - Compression moulding test
specimens of thermoplastic materials.

---------------
...