Thermal insulating products for building applications - Determination of freeze-thaw resistance

This European Standard specifies the equipment and procedures for determining the effect of successive cycling from dry conditions at -20 °C to wet conditions at 20 °C on the mechanical properties and moisture content of the product. It is applicable to thermal insulating products. It is intended to simulate freeze-thaw effects on thermal insulating products which are frequently exposed to water and low temperature conditions, e.g. inverted roofs and unprotected ground insulation. This test method is not recommended for all thermal insulating products. If relevant, the product standards will state for which products this standard is applicable.

Wärmedämmstoffe für das Bauwesen - Bestimmung des Verhaltens bei Frost-Tau-Wechselbeanspruchung

Diese Europäische Norm legt Prüfeinrichtungen und Verfahren zur Bestimmung der Auswirkungen von zyklisch aufeinanderfolgenden trockenen Umgebungsbedingungen bei −20 °C und feuchten Umgebungsbedingungen bei +20 °C auf die mechanischen Eigenschaften und den Feuchtegehalt eines Produkts fest. Sie gilt für Wärmedämmstoffe. Das Prüfverfahren simuliert das Verhalten bei Frost-Tau-Wechseln von Wärmedämmstoffen, die häufig Wasser und niedrigen Temperaturen ausgesetzt werden, wie z. B. im „Umkehrdach“ und bei der unge-schützten Wärmedämmung zum Erdreich. Dieses Prüfverfahren ist nicht für alle Wärmedämmstoffe geeignet. In den Produktnormen wird daher festgelegt, für welche der in ihnen beschriebenen Produkte diese Norm anzuwenden ist.

Produits isolants thermiques destinés aux applications du bâtiment - Détermination de la résistance aux effets du gel-dégel

La présente Norme européenne spécifie l'équipement et les modes opératoires permettant de déterminer l'effet sur les propriétés mécaniques et la teneur en eau du produit de cycles successifs entre des conditions sèches à - 20 °C et des conditions humides à 20 °C. Elle s'applique aux produits isolants thermiques.
Elle est destinée à simuler les effets du gel-dégel sur les produits isolants thermiques fréquemment exposés à l'eau et à de basses températures, par exemple en toiture inversée ou en isolation au contact direct de la terre.
Cette méthode d'essai n'est pas recommandée pour tous les produits isolants thermiques. Le cas échéant, les normes relatives aux produits mentionneront à quels produits la présente norme s'applique.

Toplotnoizolacijski proizvodi za uporabo v gradbeništvu - Ugotavljanje odpornosti proti ponavljajočemu zmrzovanju in taljenju

Te evropski standard določa opremo in postopke za ugotavljanje učinka zaporednega menjavanja iz suhega stanja pri –20 °C v mokro stanje pri 20 °C na mehanske lastnosti in vsebnost vlage v izdelku. Uporablja se za toplotnoizolacijske proizvode. Namenjen je simulaciji učinkov zamrzovanja/odtajanja na toplotnoizolacijske izdelke, ki so pogosto izpostavljeni vodi in nizkim temperaturam, npr. invertne strehe in nezaščitena izolacija tal. Ta testna metoda se ne priporoča za vse toplotnoizolacijske izdelke. Če je ustrezno, bo v standardih za izdelek navedeno, na katere izdelke se nanaša ta standard.

General Information

Status
Withdrawn
Public Enquiry End Date
29-Sep-2012
Publication Date
05-Jun-2013
Withdrawal Date
25-May-2023
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
25-May-2023
Due Date
17-Jun-2023
Completion Date
26-May-2023

Relations

Buy Standard

Standard
EN 12091:2013
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN 12091:2012
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Wärmedämmstoffe für das Bauwesen - Bestimmung des Verhaltens bei Frost-Tau-WechselbeanspruchungProduits isolants thermiques destinés aux applications du bâtiment - Détermination de la résistance aux effets du gel-dégelThermal insulating products for building applications - Determination of freeze-thaw resistance91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 12091:2013SIST EN 12091:2013en,fr,de01-julij-2013SIST EN 12091:2013SLOVENSKI
STANDARDSIST EN 12091:19991DGRPHãþD



SIST EN 12091:2013



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12091
March 2013 ICS 91.100.60 Supersedes EN 12091:1997English Version
Thermal insulating products for building applications - Determination of freeze-thaw resistance
Produits isolants thermiques destinés aux applications du bâtiment - Détermination de la résistance aux effets du gel-dégel
Wärmedämmstoffe für das Bauwesen - Bestimmung des Verhaltens bei Frost-Tau-Wechselbeanspruchung This European Standard was approved by CEN on 15 December 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12091:2013: ESIST EN 12091:2013



EN 12091:2013 (E) 2 Contents Page Foreword . 3 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 5 4 Principle. 5 5 Apparatus . 5 6 Test specimens . 6 6.1 General . 6 6.2 Dimensions of test specimens . 6 6.3 Number of test specimens . 6 6.4 Preparation of test specimens . 6 6.5 Conditioning of test specimens. 6 7 Procedure . 6 8 Calculation and expression of results . 8 8.1 Water absorption . 8 8.2 Changes in the compression behaviour . 9 9 Accuracy of measurement . 9 10 Test report . 10
SIST EN 12091:2013



EN 12091:2013 (E) 3 Foreword This document (EN 12091:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12091:1997.
The revision of this standard contains no major changes, only minor corrections and clarifications of an editorial nature. This European Standard is one of a series of standards which specify test methods for determining dimensions and properties of thermal insulating materials and products. It supports a series of product standards for thermal insulating materials and products which derive from the Council Directive of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (Directive 89/106/EEC) through the consideration of the essential requirements. This European Standard has been drafted for applications in buildings but it may also be used in other areas where it is relevant. This European test standard is one of the following group of inter-related standards on test methods for determining dimensions and properties of thermal insulation materials and products, all of which fall within the scope of CEN/TC 88:  EN 822, Thermal insulating products for building applications — Determination of length and width  EN 823, Thermal insulating products for building applications — Determination of thickness  EN 824, Thermal insulating products for building applications — Determination of squareness  EN 825, Thermal insulating products for building applications — Determination of flatness  EN 826, Thermal insulating products for building applications — Determination of compression behaviour  EN 1602, Thermal insulating products for building applications — Determination of the apparent density  EN 1603, Thermal insulating products for building applications — Determination of dimensional stability under constant normal laboratory conditions (23 °C/50 % relative humidity)  EN 1604, Thermal insulating products for building applications — Determination of dimensional stability under specified temperature and humidity conditions  EN 1605, Thermal insulating products for building applications — Determination of deformation under specified compressive load and temperature conditions  EN 1606, Thermal insulating products for building applications — Determination of compressive creep SIST EN 12091:2013



EN 12091:2013 (E) 4  EN 1607, Thermal insulating products for building applications — Determination of tensile strength perpendicular to faces  EN 1608, Thermal insulating products for building applications — Determination of tensile strength parallel to faces  EN 1609, Thermal insulating products for building applications — Determination of short-term water absorption by partial immersion  EN 12085, Thermal insulating products for building applications — Determination of linear dimensions of test specimens  EN 12086, Thermal insulating products for building applications — Determination of water vapour transmission properties  EN 12087, Thermal insulating products for building applications — Determination of long-term water absorption by immersion  EN 12088, Thermal insulating products for building applications — Determination of long-term water absorption by diffusion  EN 12089, Thermal insulating products for building applications — Determination of bending behaviour  EN 12090, Thermal insulating products for building applications — Determination of shear behaviour  EN 12091, Thermal insulating products for building applications — Determination of freeze-thaw resistance  EN 12429, Thermal insulating products for building applications — Conditioning to moisture equilibrium under specified temperature and humidity conditions  EN 12430, Thermal insulating products for building applications — Determination of behaviour under point load  EN 12431, Thermal insulating products for building applications — Determination of thickness for floating floor insulating products  EN 13793, Thermal insulating products for building applications — Determination of behaviour under cyclic loading  EN 13820, Thermal insulating materials for building applications — Determination of organic content According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Wärmedämmstoffe für das Bauwesen - Bestimmung des Verhaltens bei Frost-Tau-WechselbeanspruchungProduits isolants thermiques destinés aux applications du bâtiment - Détermination de la résistance aux effets du gel-dégelThermal insulating products for building applications - Determination of freeze-thaw resistance91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:FprEN 12091kSIST FprEN 12091:2012en,fr,de01-september-2012kSIST FprEN 12091:2012SLOVENSKI
STANDARD



kSIST FprEN 12091:2012



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 12091
June 2012 ICS 91.100.60 Will supersede EN 12091:1997English Version
Thermal insulating products for building applications - Determination of freeze-thaw resistance
Produits isolants thermiques destinés aux applications du bâtiment - Détermination de la résistance aux effets du gel-dégel
Wärmedämmstoffe für das Bauwesen - Bestimmung des Verhaltens bei Frost-Tau-Wechselbeanspruchung This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 88.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 12091:2012: EkSIST FprEN 12091:2012



FprEN 12091:2012 (E) 2 Contents Page Foreword .31 Scope .52 Normative references .53 Terms and definitions .54 Principle .55 Apparatus .55.1 Cold chamber .55.2 Watertank .65.3 Balance .65.4 Compression testing machine .66 Test specimens .66.1 General .66.2 Dimensions of test specimens .66.3 Number of test specimens .66.4 Preparation of test specimens .66.5 Conditioning of test specimens .67 Procedure .78 Calculation and expression of results .88.1 Water absorption .88.2 Changes in the compression behaviour .99 Accuracy of measurement . 1010 Test report . 10 kSIST FprEN 12091:2012



FprEN 12091:2012 (E) 3 Foreword This document (FprEN 12091:2012) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 12091:1997.
The revision of this standard contains no major changes only minor corrections and clarifications of editorial nature. This European Standard is one of a series of standards which specify test methods for determining dimensions and properties of thermal insulating materials and products. It supports a series of product standards for thermal insulating materials and products which derive from the Council Directive of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (Directive 89/106/EEC) through the consideration of the essential requirements. This European Standard has been drafted for applications in buildings but it may also be used in other areas where it is relevant. This EN test standard is one of the following group of inter-related standards on test methods for determining dimensions and properties of thermal insulation materials and products, all of which come within the scope of CEN/TC 88: EN 822, Thermal insulating products for building applications — Determination of length and width EN 823, Thermal insulating products for building applications — Determination of thickness EN 824, Thermal insulating products for building applications — Determination of squareness EN 825, Thermal insulating products for building applications — Determination of flatness EN 826, Thermal insulating products for building applications — Determination of compression behaviour EN 1602, Thermal insulating products for building applications — Determination of the apparent density EN 1603, Thermal insulating products for building applications — Determination of dimensional stability under constant normal laboratory conditions (23 °C/50 % relative humidity) EN 1604, Thermal insulating products for building applications — Determination of dimensional stability under specified temperature and humidity conditions EN 1605, Thermal insulating products for building applications — Determination of deformation under specified compressive load and temperature conditions EN 1606, Thermal insulating products for building applications — Determination of compressive creep EN 1607, Thermal insulating products for building applications — Determination of tensile strength perpendicular to faces EN 1608, Thermal insulating products for building applications — Determination of tensile strength parallel to faces kSIST FprEN 12091:2012



FprEN 12091:2012 (E) 4 EN 1609, Thermal insulating products for building applications —- Determination of short term water absorption by partial immersion EN 12085, Thermal insulating products for building applications — Determination of linear dimensions of test specimens EN 12086, Thermal insulating products for building applications — Determination of water vapour transmission properties EN 12087, Thermal insulating products for building applications — Determination of long term water absorption by immersion EN 12088, Thermal insulating products for building applications — Determination of long term water absorption by diffusion EN 12089, Thermal insulating products for building applications — Determination of bending behaviour EN 12090, Thermal insulating products for building applications — Determination of shear behaviour EN 12091, Thermal insulating products for building applications — Determination of freeze-thaw resistance
EN 12429, Thermal insulating products for building applications — Conditioning to moisture equilibrium under specified temperature and humidity conditions EN 12430, Thermal insulating products for building applications — Determination of behaviour under point load EN 12431, Thermal insulating products for building applications — Determination of thickness for floating floor insulating products EN 13793, Thermal insulating products for building applications — Determination of behaviour under cyclic loading EN 13820, Thermal
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.