SIST EN 10113-1:1997

Hot-rolled products in weldable fine grain structural steels - Part 1: General delivery conditions

1.1         This European Standard specifies requirement for long products and flat products of hot-rolled weldable fine grain structural quality and special steels. Part 1 of this European Standard specifies the general delivery conditions Part 2 of this European Standard specifies the delivery conditions for normalized steels in the grades and qualities given in table 1 (chemical composition) and tables 3 and 4 (mechanical properties) of part 2.           NOTE:   Whenever normalized is mentioned, normalized rolled is also covered (see 7.2 of part 2).           Part 3 of this European Standard specifies the delivery conditions for thermomechanical rolled steels in the grades and qualities given in table 1 (chemical composition) and tables 3 and 4 (mechanical properties) of part 3.           The steels specified in this European Standard are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storages tanks, water supply tanks, etc., for service at ambient and low temperatures.           1.2         This European Standard does not apply to products for which other EURONORMS exist or European Standards dealing with steels for general structural applications are being prepared:  -  Hot-rolled products of non-alloy structural steels - (see EN 10025), -  Semi-finished products for forging in general purpose structural stee~s - (see EURONORM 30). -  Weathering steels for structural purposes - (see EN 10155). -  Plates and wide flats made of weldable fine-grained structural steels in the quenched and tempered condition - (see prEN 10137). -  Flat products in high yield strength steels for cold forming - wide flats, sheet/plate, wide and narrow strip - (see prEN 10149). -  Steels for shipbuilding - normal and high strength qualities - (see EURONORM 156). -  Hot finished structural hollow sections (see prEN 10210-1).

Warmgewalzte Erzeugnisse aus schweißgeeigneten Feinkornbaustählen - Teil 1: Allgemeine Lieferbedingungen

Diese europäische Norm enthält die Anforderungen an Langerzeugnisse und Flacherzeugnisse aus warmgewalzten schweissgeeigneten Feinkornbaustählen, die als Qualitäts- und Edelstähle gelten. Teil 1 dieser europäischen Norm enthält die allgemeinen Lieferbedingungen. Teil 2 dieser europäischen Norm enthält die Lieferbedingungen für normalgeglühte Stähle der in Tabelle 1 (chemische Zusammensetzung) sowie in den Tabellen 3 und 4 (mechanische Eigenschaften) des Teiles 2 genannten Sorten und Gütegruppen.

Produits laminés a chaud en aciers de construction soudables a grains fins - Partie 1: Conditions générales de livraison

La présente norme européenne spécifie les caractéristiques des produits longs et des produits plats laminés a chaud, en aciers de construction de qualité et spéciaux, a grains fins, soudables. La partie 1 de la présente norme européenne traite des conditions générales de livraison. La partie 2 de la présente norme européenne traite des conditions de livraison des aciers a l'état normalisé dans les nuances et qualités données au tableau 1 (composition chimique) et aux tableaux 3 et 4 (caractéristiques mécaniques).

Vroče valjani izdelki iz varivih drobnozrnatih konstrukcijskih jekel - 1. del: Splošni dobavni pogoji

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-1997
• Withdrawal Date: 28-Feb-2005
• ICS: 77.140.10 - Heat-treatable steels
• Technical Committee: IFEK - Ferrous metals
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 01-Mar-2005
• Due Date: 01-Mar-2005
• Completion Date: 01-Mar-2005
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Mandate: M/BC/CEN/86/1 - ECISS - 1st programme
• Ref Project: EN 10113-1:1993 - Hot-rolled products in weldable fine grain structural steels - Part 1: General delivery conditions

Relations

• Replaced By: SIST EN 10025-3:2004 - Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
• Effective Date: 01-Mar-2005
• Replaced By: SIST EN 10025-1:2004 - Hot rolled products of structural steels - Part 1: General technical delivery conditions
• Effective Date: 01-Mar-2005
• Replaced By: SIST EN 10025-4:2004 - Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
• Effective Date: 01-Mar-2005
• Child: SIST EN 10113-3:1997 - Hot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels
• Effective Date: 22-Dec-2008
• Child: SIST EN 10113-2:1997 - Hot-rolled products in weldable fine grain structural steels - Part 2: Delivery conditions for normalized/normalized rolled steels
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalzte Erzeugnisse aus schweißgeeigneten Feinkornbaustählen - Teil 1: Allgemeine LieferbedingungenProduits laminés a chaud en aciers de construction soudables a grains fins - Partie 1: Conditions générales de livraisonHot-rolled products in weldable fine grain structural steels - Part 1: General delivery conditions77.140.10Jekla za toplotno obdelavoHeat-treatable steelsICS:Ta slovenski standard je istoveten z:EN 10113-1:1993SIST EN 10113-1:1997en01-maj-1997SIST EN 10113-1:1997SLOVENSKI
STANDARD



SIST EN 10113-1:1997



S
...