SIST EN 10017:2004

Steel rod for drawing and/or cold rolling - Dimensions and tolerances

This European Standard specifies the dimensions, the tolerances, the nominal cross-section and the nominal mass of steel rod for drawing.
This European Standard concerns round, square, rectangular and hexagonal rod in steel grades specified in European Standard.

Walzdraht aus Stahl zum Ziehen und/oder Kaltwalzen - Maße und Grenzabmaße

Dieses Dokument legt die Maße, Grenzabmaße, Nennquerschnitte und Nennmassen für Walzdraht zum Ziehen fest.
Dieses Dokument gilt für Rund-, Vierkant-, Flach- und Sechskantwalzdraht aus den Stahlsorten nach Europäischen Normen.

Fil machine en acier destiné au tréfilage et/ou laminage a froid - Dimensions et tolérances

La présente Norme européenne spécifie les dimensions, les tolérances, la section nominale et la masse nominale des fils machine en acier destinés au tréfilage.
La présente Norme européenne concerne les fils machine ronds, carrés, rectangulaires, hexagonaux et demi ronds en nuances d'acier non allié spécifiées dans la Norme européenne.

Jeklene palice za vlečenje in/ali hladno valjanje – Mere in tolerance

General Information

• Status: Published
• Publication Date: 30-Nov-2004
• ICS: 77.140.65 - Steel wire, wire ropes and link chains
• Technical Committee: IFEK - Ferrous metals
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Dec-2004
• Due Date: 01-Dec-2004
• Completion Date: 01-Dec-2004
• Directive: 89/106/EEC - Construction products
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Mandate: M/120 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on structural metallic products and ancillaries
• Ref Project: EN 10017:2004 - Steel rod for drawing and/or cold rolling - Dimensions and tolerances

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 10017:2004
01-december-2004
-HNOHQHSDOLFH]DYOHþHQMHLQDOLKODGQRYDOMDQMH±0HUHLQWROHUDQFH
Steel rod for drawing and/or cold rolling - Dimensions and tolerances
Walzdraht aus Stahl zum Ziehen und/oder Kaltwalzen - Maße und Grenzabmaße
Fil machine en acier destiné au tréfilage et/ou laminage a froid - Dimensions et
tolérances
Ta slovenski standard je istoveten z: EN 10017:2004
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
SIST EN 10017:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 10017:2004

---------------------- Page: 2 ----------------------

SIST EN 10017:2004



EUROPEAN STANDARD
EN 10017

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2004
ICS 77.140.65 Supersedes EURONORM 17:1970
English version
Steel rod for drawing and/or cold rolling - Dimensions and
tolerances
Fil machine en acier non allié destiné au tréfilage et/ou Walzdraht aus Stahl zum Ziehen und/oder Kaltwalzen -
laminage à froid - Dimensions et tolérances Maße und Grenzabmaße
This European Standard was approved by CEN on 9 July 2004.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10017:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 10017:2004
EN 10017:2004 (E)
Contents
Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4
4 Information to be supplied by the purchaser .4
4.1 Information to be supplied by the purchaser .4
4.2 Examples .4
5 Nominal sections and nominal mass.5
6 Dimensions and tolerances .6
6.1 Round rod (Fig. 1).6
6.2 Square rod (Fig. 2) .8
6.3 Rectangular rod (Fig. 3).9
6.4 Hexagonal Rod (Fig. 4).12
7 Mass of coils and checks on dimensional tolerances.14
8 Claims .14
Bibliography .15

2

---------------------- Page: 4 ----------------------

SIST EN 10017:2004
EN 10017:2004 (E)
Foreword
This document (EN 10017:2004) has been prepared by Technical Committee ECISS/TC 15 “Wire rod - Qualities,
dimensions, tolerances and specific tests”, the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by
April 2005.
This document supersedes EURONORM 17 (1970).
This document includes a Bibliography.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

3

---------------------- Page: 5 ----------------------

SIST EN 10017:2004
EN 10017:2004 (E)
1 Scope
This document specifies the dimensions, the tolerances, the nominal cross-section and the nominal mass of steel
rod for drawing.
This document concerns round, square, rectangular and hexagonal rod in steel grades specified in European
Standards.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
The requirements of this document rule when they differ from those in the standards and documents referred to
below.
EN 10021, General technical delivery requirements for steel and iron products
EN 10079:1992, Definition of steel products
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10079:1992 apply.
4 Information to be supplied by the purchaser
4.1 Information to be supplied by the purchaser
The following information shall be supplied by the purchaser at the time of enquiry and order, to enable the supplier
to comply satisfactorily with the requirements of this document:
a) quantity to be delivered
b) product denomination (rod)
c) section (round, square, rectangular, hexagonal)
d) reference to this document
e) nominal dimensions in millimetres
f) information included in the quality product European Standard
4.2 Examples
Round rod with a diameter of 10 mm in steel C10D according EN 10016-2:
EXAMPLE 1 Round rod EN 10017 - 10 - EN 10016-2 - C10D
4

---------------------- Page: 6 ----------------------

SIST EN 10017:2004
EN 10017:2004 (E)
Rectangular rod with a width of 30 mm and thickness 5 mm in steel C3D1 according EN 10016-3:
EXAMPLE 2 Rectangular rod EN 10017 - 30 x 5 - EN 10016-3 - C3D1
Hexagonal rod with a wrench opening of 10 mm in steel C70D2 according EN 10016-4:
EXAMPLE 3 Hexagonal rod EN 10017 - 10 - EN 10016-4 - C70D2
5 Nominal sections and nominal mass
The values for sections and mass are shown in Tables 1 to 4 and are given as a guide.
3.
They have been calculated and rounded off on the basis of nominal sizes and a density of 7,85 kg/dm
For stainless steels to calculate the nominal mass, densities should be obtained from EN 10088-1.
5

---------------------- Page: 7 ----------------------

SIST EN 10017:2004
EN 10017:2004 (E)
6 Dimensions and tolerances
6.1 Round rod (Fig. 1)

Figure 1 — Round rod
Table 1 — Dimensions, tolerances, nominal section and nominal mass
Tolerance on
Tolerance on Nominal Nominal
Nominal diameter d
a
diameter section mass
ovality

2
(mm) (mm) (mm) (kg/m)
(mm)
5 19,63 0,154
± 0,3
5,5 23,76 0,187
± 0,3
6 28,27 0,222
± 0,3
...