iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST ENV 50275-1:2002

(Main)

Conductive charging for electric vehicles -- Part 1: General considerations

Conductive charging for electric vehicles -- Part 1: General considerations

D122/068: To be withdrawn by CLC/prTS 50457-1 (PR=16661) and 2 (PR=16662) when approved * D124/135: CLC/TC 69X disbanded

Konduktive Ladung von Elektrofahrzeugen -- Teil 1: Allgemeine Überlegungen

Charge conductive pour véhicules éléctriques -- Partie 1: Généralités

Conductive charging for electric vehicles - Part 1: General considerations

General Information

Status
Withdrawn
Publication Date
31-Aug-2002
Withdrawal Date
20-Oct-2009
ICS
43.120 - Electric road vehicles
Technical Committee
I11 - Imaginarni 11
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
19-Oct-2009
Due Date
11-Nov-2009
Completion Date
21-Oct-2009
Ref Project
ENV 50275-1:1998 - Conductive charging for electric vehicles - Part 1: General considerations

Buy Standard

ENV 50275-1:2002ENV 50275-1:2002
PreviousNext
Standardization document
ENV 50275-1:2002
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ENV 50275-1:2002
01-september-2002
Conductive charging for electric vehicles - Part 1: General considerations
Conductive charging for electric vehicles -- Part 1: General considerations
Konduktive Ladung von Elektrofahrzeugen -- Teil 1: Allgemeine Überlegungen
Charge conductive pour véhicules éléctriques -- Partie 1: Généralités
Ta slovenski standard je istoveten z: ENV 50275-1:1998
ICS:
43.120 (OHNWULþQDFHVWQDYR]LOD Electric road vehicles
SIST ENV 50275-1:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ENV 50275-1:2002

---------------------- Page: 2 ----------------------

SIST ENV 50275-1:2002

---------------------- Page: 3 ----------------------

SIST ENV 50275-1:2002

---------------------- Page: 4 ----------------------

SIST ENV 50275-1:2002

---------------------- Page: 5 ----------------------

SIST ENV 50275-1:2002

---------------------- Page: 6 ----------------------

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
oSIST prEN IEC 63281-0:2022(Main)
E-Transporters - Terminology and classification
prEN IEC 63281-2-1
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN IEC 63281-2-1:2022(Main)
Personal e-Transporters - Part 2-1: Test method for total run time of e-scooter with consideration to environmental conditions of actual use
prEN IEC 63281-3-1
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
kSIST FprEN IEC 63281-1:2023(Main)
E-Transporters - Part 1: Terminology and classification
EN IEC 63281-1:2023
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN IEC 63281-3-2:2023(Main)
E-Transporters - Part 3-2: Performance test methods for mobility of cargo e-Transporters
prEN IEC 63281-3-2:2023
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 55036:2020/A1:2023(Amendment)
Amendment 1 - Electric and hybrid electric road vehicles - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers below 30 MHz
EN IEC 55036:2020/A1:2023
  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61980-2:2023(Main)
Electric vehicle wireless power transfer (WPT) systems - Part 2: Specific requirements for MF-WPT system communication and activities (IEC 61980-2:2023)
EN IEC 61980-2:2023

This Part of IEC 61980 addresses communication and activities of magnetic field wireless power transfer (MF-WPT) systems.
The requirements in this document are intended to be applied for MF-WPT systems accordin to IEC 61980-3 and ISO 19363.
The aspects covered in this document include:
- operational and functional characteristics of the MF-WPT communication system and related activities
- operational and functional characteristics of the positioning system
The following aspects are under consideration for future documents:
- requirements for two- and three-wheel vehicles,
- requirements for MF-WPT systems supplying power to EVs in motion, and
- requirements for bidirectional power transfer
Note: Any internal communication at Supply device or EV device is not in the scope of this document

  • Standard
    97 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CLC/TS 50717:2023(Main)
Technical Requirements for Current Collectors for ground-level feeding system on road vehicles in operation
CLC/TS 50717:2022

This document specifies the general characteristics which are to be applied to ground level current collector devices, to enable conductive current collection by road vehicles from a feeding track integrated in the roadway.
It defines the interfaces between the current collector device and its environment as well as the electrical safety concept.
It also specifies the necessary tests for the current collector devices and gives recommendations for their maintenance.
This document is applicable to current collector devices on road vehicles for ground-level feeding operation on electrified public roads and highways.
This document is not applicable to motorcycles (including tricycles and quadricycles).
This document is not applicable to vehicles or electric buses with dynamic or static inductive charging systems and related power supplies.

  • Technical specification
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62196-1:2023(Main)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements (IEC 62196-1:2022)
EN IEC 62196-1:2022

This part of IEC 62196 is applicable to EV plugs, EV socket-outlets, vehicle connectors, vehicle inlets, herein referred to as "accessories", and to cable assemblies for electric vehicles (EV) intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding:
- 690 V AC 50 Hz to 60 Hz, at a rated current not exceeding 250 A;
- 1 500 V DC at a rated current not exceeding 800 A.
These accessories and cable assemblies are intended to be installed by instructed persons (IEV 195-04-02) or skilled persons (IEV 195-04-01) only.
These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851 (all parts), which operate at different voltages and frequencies, and which can include extra-low voltage and communication signals.
These accessories and cable assemblies are intended to be used at an ambient temperature between −30 °C and +40 °C.
NOTE 1 In some countries, other requirements can apply.
NOTE 2 In the following country, −35 °C applies: SE.
NOTE 3 The manufacturer can enlarge the temperature range on the condition that the specified range information is provided.
These accessories are intended to be connected only to cables with copper or copper-alloy conductors.
The accessories covered by this document are intended for use in electric vehicle supply equipment in accordance with IEC 61851 (all parts).
This document does not apply to standard plug and socket-outlets used for mode 1 and mode 2 according to IEC 61851-1:2017, 6.2.
NOTE 4 In the following countries, mode 1 is not allowed: UK, US, CA, SG.

  • Standard
    101 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62196-3:2023(Main)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility requirements for DC and AC/DC pin and contact-tube vehicle couplers (IEC 62196-3:2022)
EN IEC 62196-3:2022

This part of IEC 62196 is applicable to vehicle couplers with pins and contact tubes of standardized configuration, herein also referred to as "accessories", intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage and current in accordance with IEC 62196-1:2022.
This document applies to high power DC interfaces and combined AC/DC interfaces of vehicle couplers that are intended for use in conductive charging systems for circuits specified in IEC 61851-1:2017 and IEC 6185123:-2.
The DC vehicle connectors and inlets covered by this document are used only in charging mode 4, according to IEC 618511:2017, 6.2.4, and case C, as shown in IEC 618511:2017, Figure 3.
These vehicle couplers are intended to be used for circuits specified in IEC 61851-23: - which operate at different voltages, and which can include ELV and communication signals.
This document applies to the vehicle couplers to be used in an ambient temperature between -30 °C and +40 °C.
NOTE 1 In some countries, other requirements may apply.
NOTE 2 In the following country, −35 °C applies: SE.
These vehicle couplers are intended to be connected only to cables with copper or copper-alloy conductors.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62196-2:2023(Main)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories (IEC 62196-2:2022)
EN IEC 62196-2:2022

This part of IEC 62196 applies to EV plugs, EV socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. These accessories have a nominal rated operating voltage not exceeding 480 V AC, 50 Hz to 60 Hz, and a rated current not exceeding 63 A three phase or 70 A single phase, for use in conductive charging of electric vehicles.
This document covers the basic interface accessories for vehicle supply as specified in IEC 62196-1.
NOTE 1 The term "Electric road vehicles (EV)" comprises all road vehicles, including plug-in hybrid road vehicles (PHEV) that derive all or part of their energy from the rechargeable energy storage systems (RESS).
These accessories are intended to be used for circuits specified in IEC 61851-1:2017, which operate at different voltages and frequencies, and which can include extra-low voltage (ELV) and communication signals.
The use of these accessories for bidirectional power transfer is under consideration.
This document applies to accessories to be used in an ambient temperature between -30 °C and +40 °C.
NOTE 2 In the following country, other requirements regarding the lower temperature may apply: NO.
NOTE 3 In the following country, −35 °C applies: SE.
These accessories are intended to be connected only to cables with copper or copper-alloy conductors.
Vehicle inlets and vehicle connectors described in this document are intended to be used for charging in modes 1, 2 and 3, cases B and C. The EV socket-outlets and EV plugs covered by this document are intended to be used for charging mode 3 only, case A and B.
The modes and permissible connections are specified in IEC 61851-1:2017.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day