SIST EN ISO 20844:2004

Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle (ISO 20844:2004)

This International Standard specifies a method to assess the resistance to shear stresses applied to mineral oils, synthetic oils and fluids, containing polymers, when passed through a specified diesel injector nozzle. The shear stability is measured  by the change in viscosity
of the fluid under test, brought about by the polymer degradation during stress. Under normal circumstances, this International Standard
is applied to class HV hydraulic fluids as defined defined in ISO 6743-4, but it may also be applied to fire-resistant hydraulic fluids within classes HFA, HFB, HFC and HFD, with modified conditions as specified in ISO 12922.
This International Standard does not necessarily predict changes in properties of oils and fluids in actual service, but provides standardized conditions for the evaluation of polymer stability under minimized thermal and oxidative stresses. It is normally used by manufacturers of fluids and additives, and users, as a means of ranking existing and potential formulations.
NOTE 1 - Changes in other properties than viscosity are specified in some specifications, but these are not covered by the procedures specified in this International Standard.

Mineralölerzeugnisse und verwandte Produkte - Bestimmung der Scherstabilität von polymerhaltigen Ölen mit Hilfe einer Diesel-Einspritzdüse (ISO 20844:2004)

Diese Internationale Norm beschreibt ein Prüfverfahren mit Dieseleinspritzdüse zur Bewertung des relativen Viskositätsabfalls durch Scherung und ist anwendbar für Mineralöle, synthetische Öle und andere Druckflüssigkeiten, die polymere Zusätze enthalten. Das Maß der Scherstabiliät ist in dieser Norm der definierte Viskositätsverlust der polymeren Zusätze durch Scherbeanspruchung. In der Regel wird dieses Prüfverfahren für Hydrauliköle der Klassen HR und HV nach ISO 6743-4 angewendet, deren Anforderungen in ISO 11158 spezifiziert sind. Unter angepassten Bedingungen können nach diesem Prüfverfahren jedoch auch schwerentflammbare Druckflüssigkeiten der Klassen HFA, HFB, HFC und HFD geprüft werden, deren Anforderungen in ISO 12922 beschrieben sind.
Das Ergebnis der Prüfung nach dieser Internationale Norm muss nicht notwendigerweise mit den Änderungen der Eigenschaften von Ölen oder Druckflüssigkeiten in der praktischen Anwendung übereinstimmen. Es ermöglicht jedoch eine Bewertung der Scherstabilität polymerer Zusätze unter standardisierter Beanspruchung bei minimierten thermischen und oxidativen Bedingungen. Das Prüfverfahren findet üblicherweise Anwendung bei Herstellern von Flüssigkeiten, Additiven und Anwendern ist eine Hilfe bei der Bewertung existierender oder potentieller Formulierungen.
ANMERKUNG   In dem Prüfverfahren nach dieser Internationalen Norm sind Anforderungen der Änderungen von Eigenschaften oder der Viskosität nicht festgelegt.
Dieses Prüfverfahren ist eine Anforderung aus dem 7. Luxemburger Bericht ) .

Pétrole et produits connexes - Détermination de la stabilité au cisaillement de fluides contenant des polymeres au moyen d'un injecteur pour moteur diesel (ISO 20844:2004

L'ISO 20844:2004 spécifie une méthode d'évaluation de la capacité des huiles minérales et synthétiques et d'autres fluides contenant des polymères à résister aux contraintes de cisaillement mécanique appliquées quand ils circulent à travers un injecteur pour moteur diesel spécifié. La stabilité au cisaillement est mesurée par la variation de viscosité du fluide soumis à l'essai, occasionnée par l'altération du polymère durant l'application de la contrainte. Normalement, l'ISO 20844:2004 s'applique aux fluides hydrauliques des catégories HR et HV définies dans l'ISO 6743-4 et spécifiées dans l'ISO 11158, mais elle peut également être appliquée aux fluides hydrauliques difficilement inflammables des catégories HFA, HFB, HFC et HFD dans des conditions modifiées, comme cela est spécifié dans l'ISO 12922.
Aucune corrélation formelle n'a été établie entre la chute de viscosité, ou l'absence de chute de viscosité, obtenue à l'aide des méthodes décrites dans l'ISO 20844:2004 et l'évolution de la viscosité d'huiles ou de fluides en service réel. L'ISO 20844:2004 procure cependant des conditions normalisées pour évaluer la stabilité des polymères avec des contraintes d'oxydation et thermiques minimales. Elle est généralement utilisée par les fabricants de fluides et d'additifs, ainsi que par les utilisateurs des fluides, comme moyen pour classer des formulations existantes ou en développement.
Certaines spécifications spécifient des variations de caractéristiques autres que la viscosité. Celles-ci ne relèvent pas des méthodes spécifiées dans l'ISO 20844:2004.

Naftni in sorodni proizvodi - Ugotavljanje strižne stabilnosti tekočin, ki vsebujejo polimere, z uporabo dizelskih vbrizgalnih šob (ISO 20844:2004)

General Information

• Status: Withdrawn
• Publication Date: 31-Aug-2004
• Withdrawal Date: 07-Oct-2015
• ICS: 75.080 - Petroleum products in general
• Technical Committee: NAD - Petroleum products, lubricants and related products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 08-Oct-2015
• Due Date: 31-Oct-2015
• Completion Date: 08-Oct-2015
• Directive: 92/104/EC - Council Directive 92/104/EEC of 3 December 1992 on the minimum requirements for improving the safety and health protection of workers in surface and underground mineral-extracting industries (twelfth individual Directive within the meaning of Article 16 (1) of Directive 89/391/EEC)
• Mandate: M/238 - Mandate to CEN for standardization in the field of fire-resistant hydraulic fluids used for power transmission and control (hydrostatic and hydrokinetic)
• Ref Project: EN ISO 20844:2004 - Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle (ISO 20844:2004)

Relations

• Replaced By: SIST EN ISO 20844:2015 - Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle (ISO 20844:2015)
• Effective Date: 01-Dec-2015
• Replaced By: SIST EN ISO 20844:2015 - Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle (ISO 20844:2015)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 20844:2004
01-september-2004
1DIWQLLQVRURGQLSURL]YRGL8JRWDYOMDQMHVWULåQHVWDELOQRVWLWHNRþLQNLYVHEXMHMR
SROLPHUH]XSRUDERGL]HOVNLKYEUL]JDOQLKãRE,62
Petroleum and related products - Determination of the shear stability of polymer-
containing oils using a diesel injector nozzle (ISO 20844:2004)
Mineralölerzeugnisse und verwandte Produkte - Bestimmung der Scherstabilität von
polymerhaltigen Ölen mit Hilfe einer Diesel-Einspritzdüse (ISO 20844:2004)
Pétrole et produits connexes - Détermination de la stabilité au cisaillement de fluides
contenant des polymeres au moyen d'un injecteur pour moteur diesel (ISO 20844:2004
Ta slovenski standard je istoveten z: EN ISO 20844:2004
ICS:
75.080 Naftni proizvodi na splošno Petroleum products in
general
SIST EN ISO 20844:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 20844:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 20844:2004
EUROPEAN STANDARD
EN ISO 20844
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2004
ICS 75.080
English version
Petroleum and related products - Determination of the shear
stability of polymer-containing oils using a diesel injector nozzle
(ISO 20844:2004)
Pétrole et produits connexes - Détermination de la stabilité Mineralölerzeugnisse und verwandte Produkte -
au cisaillement de fluides contenant des polymères au Bestimmung der Scherstabilität von polymerhaltigen Ölen
moyen d'un injecteur pour moteur diesel (ISO 20844:2004) mit Hilfe einer Diesel-Einspritzdüse (ISO 20844:2004)
This European Standard was approved by CEN on 1 March 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20844:2004 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 20844:2004
EN ISO 20844:2004 (E)
Foreword
This document (EN ISO 20844:2004) has been prepared by Technical Committee ISO/TC 28
"Petroleum products and lubricants" in collaboration with Technical Committee CEN/TC 19
"Petroleum products, lubricants and related products", the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by September 2004, and conflicting national
standards shall be withdrawn at the latest by September 2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 20844:2004 has been approved by CEN as EN ISO 20844:2004 without any
modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 20844:2004

INTERNATIONAL ISO
STANDARD 20844
First edition
2004-03-15

Petroleum and related products —
Determination of the shear stability of
polymer-containing oils using a diesel
injector nozzle
Pétrole et produits connexes — Détermination de la stabilité au
cisaillement de fluides contenant des polymères au moyen d'un
injecteur pour moteur diesel




Reference number
ISO 20844:2004(E)
©
ISO 2004

---------------------- Page: 5 ----------------------

SIST EN ISO 20844:2004
ISO 20844:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 20844:2004
ISO 20844:2004(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Principle . 2
5 Reagents and materials. 2
6 Apparatus. 2
7 Samples and sampling . 3
8 Preparation of test rig. 3
9 Calibration. 3
10 Procedure. 4
11 Calculation. 4
12 Expression of results. 4
13 Precision . 5
14 Test report. 5
Annex A (normative) Test rig . 6
Bibliography . 9

© ISO 2004 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 20844:2004
ISO 20844:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 20844 was prepared by Technical Committee ISO/TC 28, Petroleum products and lubricants.

iv © ISO 2004 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 20844:2004
INTERNATIONAL STANDARD ISO 20844:2004(E)

Petroleum and related products — Determination of the shear
stability of polymer-containing oils using a diesel injector
nozzle
WARNING —The use of this International Standard may involve hazardous materials, operations and
equipment. This International Standard does not purport to address all of the safety problems
associated with its use. It is the responsibility of the user of this International Standard to establish
appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
1 Scope
This International Standard specifies a method to assess the resistance to shear stresses applied to mineral
oils, synthetic oils and other fluids containing polymers, when passed through a specified diesel injector
nozzle. The shear stability is measured by the change in viscosity of the fluid under test, brought about by the
polymer degradation during stress. Under normal circumstances, this International Standard is applied to
hydraulic fluids of categories HR and HV as defined in ISO 6743-4 ([1] in the Bibliography) and specified in
ISO 11158 ([2] in the Bibliography), but it may also be applied to fire-resistant hydraulic fluids within categories
HFA, HFB, HFC and HFD, with modified conditions as specified in ISO 12922 ([3] in the Bibliography).
No formal correlation has been established between the viscosity loss, or the absence of viscosity loss,
obtained using the procedures described in this International Standard and that of oils and fluids in actual
service. However, it provides standardized conditions for the evaluation of polymer stability under minimized
thermal and oxidative stresses. It is normally used by manufacturers of fluids and additives, and users, as a
means of ranking existing and potential formulations.
NOTE Changes to properties other than viscosity are specified in some specifications, but these are not covered by
the procedures specified in this International Standard.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3104:1994, Petroleum products — Transparent and opaque liquids — Determination of kinematic
viscosity and calculation of dynamic viscosity
ISO 3170:2004, Petroleum liquids — Manual sampling
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
© ISO 2004 – All rights reserved 1

---------------------- Page: 9 ----------------------

SIST EN ISO 20844:2004
ISO 20844:2004(E)
3.1
shear stability
percentage loss in viscosity at 40 °C of an oil or fluid subjected to the mechanical shear stresses specified in
this International Standard
NOTE Viscosity measurements at other temperatures may be specified by some users.
3.2
calibration pressure
2
recorded gauge pressure when the specified calibration fluid is within a viscosity loss range of 2,7 mm /s to
2
3,0 mm /s at 100 °C
4 Principle
A test portion of the oil or fluid under test is pumped through a diesel injector nozz
...