SIST EN 1870-3:2002/kprA1:2008
(Amendment)Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 3: Von oben schneidende Kappsägemaschinen und kombinierte Kapp- und Tischkreissägemaschinen
Sécurité des machines pour le travail du bois - Machines à scier circulaires - Partie 3: Tronçonneuses à coupe descendante et tronçonneuses mixtes à coupe descendante et scies à table
Varnost lesnoobdelovalnih strojev - Krožne žage - 3. del: Čelilne žage za rezanje od zgoraj navzdol in kombinirane čelilne in krožne žage z delovno mizo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1870-3:2002/kprA1:2008
01-oktober-2008
9DUQRVWOHVQRREGHORYDOQLKVWURMHY.URåQHåDJHGHO ýHOLOQHåDJH]DUH]DQMH
RG]JRUDMQDY]GROLQNRPELQLUDQHþHOLOQHLQNURåQHåDJH]GHORYQRPL]R
Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting
cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 3: Von oben
schneidende Kappsägemaschinen und kombinierte Kapp- und Tischkreissägemaschinen
Sécurité des machines pour le travail du bois - Machines à scier circulaires - Partie 3:
Tronçonneuses à coupe descendante et tronçonneuses mixtes à coupe descendante et
scies à table
Ta slovenski standard je istoveten z: EN 1870-3:2001/prA1
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870-3:2002/kprA1:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1870-3:2002/kprA1:2008
---------------------- Page: 2 ----------------------
SIST EN 1870-3:2002/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 1870-3:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
June 2008
ICS 79.120.10
English Version
Safety of woodworking machines - Circular sawing machines -
Part 3: Down cutting cross-cut saws and dual purpose down
cutting cross-cut saws/circular saw benches
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scier circulaires - Partie 3: Tronçonneuses à coupe Kreissägemaschinen - Teil 3: Von oben schneidende
descendante et tronçonneuses mixtes à coupe Kappsägemaschinen und kombinierte Kapp- und
descendante et scies à table Tischkreissägemaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1870-3:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-3:2001/prA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1870-3:2002/kprA1:2008
EN 1870-3:2001/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Clause 1, Scope.4
3 Modification to Clause 2, Normative references .4
4 Modification to Clause 3, Terms and definitions.6
5 Modification to Clause 4, List of hazards.6
6 Modification to Clause 5, Safety requirements and/or protective measures (hanging
paragraph) .9
7 Modification to 5.1.1, Safety and reliability of control systems.9
8 Modifications to 5.1.2.3, Semi-automatic machines; 5.1.2.4, Automatic machines; 5.1.3,
Starting and 5.1.4.2, Manual machines.9
9 Modification to 5.1.5, Emergency stop .9
10 Modification to 5.1.8, Failure of the power supply .9
11 Modification to 5.2.2, Risk of break-up during operation .9
12 Modification to 5.2.3.1, Spindle locking.9
13 Modification to 5.2.5, Devices to minimise the possibility or the effect of ejection .10
14 Modification to 5.2.7.5, Guarding of dual purpose down cutting cross-cut saws/circular
saw benches.10
15 Modification to 5.3.1, Fire and explosion .10
16 Modification to 5.3.4, Electricity.10
17 Modification to 5.3.5, Ergonomics and handling.10
18 Modification to 5.3.12, Radiation.11
19 Modification to 5.3.13, Laser.11
20 Modification to 5.3.16, Isolation .11
21 Modification to 5.3.17, Maintenance .12
22 Modification to Clause 6, Information for use (hanging paragraph) .12
23 Modification to 6.2.2, Marking of the machine.12
24 Modification to 6.3, Instruction handbook .13
25 Deletion of Annex D.14
26 Modification of Annex ZA .15
27 Addition of Annex ZB .16
28 Modification to the Bibliography.17
2
---------------------- Page: 4 ----------------------
SIST EN 1870-3:2002/kprA1:2008
EN 1870-3:2001/prA1:2008 (E)
Foreword
This document (EN 1870-3:2001/prA1:2008) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
3
---------------------- Page: 5 ----------------------
SIST EN 1870-3:2002/kprA1:2008
EN 1870-3:2001/prA1:2008 (E)
1 Modification to the Foreword
Replace the fifth paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
2 Modification to Clause 1, Scope
Replace the first paragraph with the following "This European Standard deals with the significant hazards,
hazardous situations and events as listed in Clause 4 which are relevant to down cutting cross-cut saws and
dual purpose down cutting cross-cut saws/circular saw benches, herein after referred to as „machines“,
designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered
with plastic edging and/or plastic/light alloy laminates.".
After the first paragraph, add the following NOTE "NOTE 1 For the definition of down cutting cross-cut saws and
dual purpose down cutting cross -cut saws/circular saw benches see 3.2, 3.3 and 3.4 and for the definition of displaceable
machine see 3.8.".
In the second paragraph, replace the second list item with the following: "- hand-held motor-operated electric
tools or any adaptation permitting their use in a different mode, i.e. bench mounting;".
After the second list item, add the following NOTE: "NOTE 2 Hand-held motor-operated electric tools and saw
benches to form an integrated whole with a hand-held motor-operated electric tools are covered by EN 60745-1:2003
together with EN 60745-2-5:2003.".
In the second paragraph, replace the third list item with the following: "- transportable machines set up on a
bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of
being lifted by one person by hand.".
After the third list item, add the following NOTE: "NOTE 3 Transportable motor-operated electric tools are
covered by the requirements of EN 61029-1:2000 together with EN 61029-2-1:2002.".
3 Modification to Clause 2, Normative references
Replace the standard paragraph with the following: "The following referenced documents are indispensable
for the application of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.".
Delete reference EN 292-1:1991 in Clause 2 and replace "EN 292-1:1991" with "EN ISO 12100-1:2003"
throughout the document.
Delete references EN 292-2:1991 and EN 292/A1:1995.
Replace reference to EN 418:1992 with: "EN ISO 13850:2006, Safety of machinery — Emergency stop —
st
Principles for design (ISO 13850:2006)" and replace "EN 418:1992" in 5.1.5, 1 paragraph, with
"EN ISO 13850".
Replace "EN 847-1:1997" with "EN 847-1:2005" throughout the document.
Replace "EN 1870-1:1999" with "EN 1870-1:2007" throughout the document.
Replace "EN 60204-1:1992" with "EN 60204-1:2006" and replace in the title
"(IEC 60204-1:1992, modified)" with "(IEC 60204-1:2005, modified)".
4
---------------------- Page: 6 ----------------------
SIST EN 1870-3:2002/kprA1:2008
EN 1870-3:2001/prA1:2008 (E)
Replace "EN 60947-4-1:1992" with "EN 60497-4-1:2001" throughout the document and replace in the title
"(IEC 60947-4-1:1990)" with "(IEC 60947-5-1:2000)".
Replace "EN 60947-5-1:1997" with "EN 60497-5-1:2004" throughout the document and replace in the title
"(IEC 60947-5-1:1997)" with "(IEC 60947-5-1:2003)".
Replace "EN 61029-1:1996" with "EN 61029-1:2000" throughout the document and replace in the title
"(IEC 1029-1:1990, modified)" with "(IEC 61029-1:1990, modified)".
Replace "prEN 61029-2-9" with "EN 61029-2-9" throughout the document.
nd
Replace "prEN 61029-2-11" with "EN 61029-2-11" throughout the document and the 2 element of the title
with "Part 2-11: Particular requirements for combined mitre and bench saws (IEC 61029-2-11:2001, modified)".
Replace "prEN 61496-2" with "CLC/TS 61496-2:2006" in Clause 2 and "prEN 61496-2" with "CLC/TS 61496-
rd
2" throughout the document and the 3 element of the title with "Part 2: Particular requirements for equipment
using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2006)".
Replace reference to "ISO 3745:1997" with "EN ISO 3745:2003, Acoustics — Determination of sound power
levels of noise sources using sound pressure — Precision methods for anechoic and semi-anechoic rooms
(ISO 3745:2003)" and replace "ISO 3745:1997" with "EN ISO 3745:2003" throughout the document.
Replace reference to "HD 21.1 S3:1997" with "HD 21.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having thermoplastic insulation — Part 1: General requirements" and replace "HD 21.1
S3:1997" with "HD 21.1 S4:2002" throughout the document.
Replace reference to "HD 22.1 S3:1997" with "HD 22.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having cross-linked insulation — Part 1: General requirements" and replace "HD 22.1
S3:1997" with "HD 22.1 S4:2002" throughout the document.
Replace reference to "HD 22.4 S3:1995" with "HD 22.4 S4:2004, Cables of rated voltages up to and including
450/750 V and having crosslinked insulation — Part 4: Cords and flexible cables" and replace "HD 22.4
S3:1995" with "HD 22.4 S4:2004" throughout the document.
Add the following references:
"EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general
principles",
"EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators",
"EN 1005-1:2001, Safety of machinery — Human physical performance — Part 1: Terms and definitions
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits
for machinery operation
EN 1005-4:2005, Safety of machinery — Human physical performance — Part 4: Evaluation of working
postures and movements in relation to machinery
5
---------------------- Page: 7 ----------------------
SIST EN 1870-3:2002/kprA1:2008
EN 1870-3:2001/prA1:2008 (E)
EN 1037:1995, Safety of machinery — Prevention of unexpected start-up",
"EN 50370-1:2005, Electromagnetic compatibility (EMC) — Product family standard for machine-tools —
Part 1: Emission
EN 50370-2:2003, Electromagnetic compatibility (EMC) — Product family standard for machine-tools —
Part 2: Immunity",
"EN 60439-1:1999, Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially
type-tested assemblies (IEC 60439-1:1999)",
"EN 61310-1:1995, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for
visual, auditory and tactile signals (IEC 61310-1:1995)" and
"EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology and methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles (ISO 12100-2:2003)".
4 Modification to Clause 3, Terms and definitions
Definition 3.8, replace the term with "displaceable machine".
Definition 3.21, replace the term with "information from the supplier".
5 Modification to Clause 4, List of hazards
Replace the title of Clause 4 with "List of significant hazards".
Replace the clause content with:
"This clause contains the significant hazards, hazardous situations and events (see EN 1050:1996) as far as
they are dealt with in this document, identified by risk assessment as significant for the machines as defined in
the scope and which require action to eliminate or reduce the risk. This document deals with these significant
hazards by defining safety requirements and/or measures or by reference to relevant standards.
These hazards are listed in Table 1 in accordance with Annex A of EN 1050:1996.
6
---------------------- Page: 8 ----------------------
SIST EN 1870-3:2002/kprA1:2008
EN 1870-3:2001/prA1:2008 (E)
Table 1 — List of significant hazards
Hazards, hazardous situations and Relevant sub-
No hazardous events EN ISO 12100 clause of this
document
Part 1: Part 2:
2003 2003
1 Mechanical hazards related to:
- machine parts or workpieces:
a) shape; 4.2 4.2.1, 5.2.3, 5.2.5,
4.2.2, 5 5.2.6, 5.2.7,
5.2.8, 5.2.9
b) relative location; 5.1.2, 5.2.5,
5.2.6, 5.2.8
c) mass and stability (potential energy of 5.2.7
elements which may move under the
effect of gravity)
d) mass and velocity (kinetic energy of 5.2.7
elements in controlled or uncontrolled
motion);
e) mechanical strength. 5.2.2, 5.2.3,
5.2.5, 5.2.6,
5.2.9
- accumulation of energy inside the machinery:
f) elastic elements (springs), or 4.2 4.10, 5.5.4 5.2.7
g) liquids and gases under pressure; 4.2 4.10, 5.5.4 5.2.7
1.1 Crushing hazard 4.2.1 5.2.7, 5.2.8
1.2 Shearing hazard 5.2.7, 5.2.8
1.3 Cutting or severing hazard 5.2.2, 5.2.3,
5.2.4, 5.2.7
1.4 Entanglement hazard 5.2.7
1.5 Drawing-in or trapping hazard 5.2.7
1.9 High pressure fluid injection or ejection 5.2.2, 5.2.3,
hazard 5.2.5, 5.2.6,
5.2.8, 5.3.7
2 Electrical hazards due to:
2.1 Contact of persons with live parts (direct 4.3 4.9, 5.5.4 5.3.4, 5.3.16
contact)
2.2 Contact of persons with parts which have 4.3 4.9 5.3.4, 5.3.16
become live under faulty conditions
(indirect contact)
4 Hazards generated by noise, resulting in:
Hearing loss (deafness), other 4.5 4.2.2, 5 5.3.2
4.1
physiological disorders (loss of balance,
loss of awareness)
Interference with speech communication, 5.3.2
4.2
acoustic signals
7
---------------------- Page: 9 ----------------------
SIST EN 1870-3:2002/kprA1:2008
EN 1870-3:2001/prA1:2008 (E)
Hazards generated by radiation
6
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.