Testing concrete in structures - Part 1: Cored specimens - Taking, examining and testing in compression

This European Standard specifies a method for taking cores from hardened concrete, their examination, preparation for testing and determination of compressive strength.
NOTE 1   This European Standard does not give guidance on the decision to drill cores or on the locations for drilling.
NOTE 2   This European Standard does not provide procedures for interpreting the core strength results.
NOTE 3   For the assessment of in-situ compressive strength in structures and precast concrete components EN 13791 may be used.

Prüfung von Beton in Bauwerken - Teil 1: Bohrkernproben - Herstellung, Untersuchung und Prüfung der Druckfestigkeit

Dieses Dokument legt ein Verfahren zur Entnahme von Bohrkernen aus Festbeton, deren Untersuchung sowie deren Vorbereitung für die Prüfung und für die Bestimmung der Druckfestigkeit fest.
Dieses Dokument enthält keine Anleitungen für die Entscheidung zur Entnahme von Bohrkernen oder für die Entnahmestellen.
Dieses Dokument enthält keine Verfahren für die Auswertung der Ergebnisse der Festigkeit von Bohrkernen.
Zur Bewertung der Druckfestigkeit von Beton in Bauwerken oder in Bauwerksteilen darf EN 13791 angewendet werden.

Essais pour béton dans les structures - Partie 1 : Carottes - Prélèvement, examen et essais en compression

Le présent document spécifie une méthode qui permet d’effectuer le prélèvement de carottes de béton durci, de les examiner, de les préparer avant l’essai et de déterminer leur résistance à la compression.
Le présent document ne fournit pas de recommandations quant à la pertinence de l’extraction de carottes ou à l’emplacement des carottages dans l’ouvrage.
Il ne spécifie pas de modes opératoires pour l’interprétation des résultats des essais de résistance effectués sur les carottes.
Pour évaluer sur site la résistance à la compression des structures et des éléments préfabriqués en béton, l’EN 13791 peut être utilisée.

Preskušanje betona v konstrukcijah - 1. del: Izvrtani preskušanci - Jemanje, pregled in tlačni preskus

Ta evropski standard določa metodo jemanja preskušancev, izvrtanih iz strjenega betona, njihovega pregleda, priprave na preskušanje in določanja tlačne trdnosti.
OPOMBA 1:   Ta evropski standard ne podaja napotkov za odločitev o vrtanju preskušancev ali o lokacijah za vrtanje.
OPOMBA 2:   Ta evropski standard ne določa postopkov za razlago rezultatov trdnosti preskušancev.
OPOMBA 3:   Za ocenjevanje in-situ tlačne trdnosti v konstrukcijah in montažnih betonskih elementih se lahko uporablja standard EN 13791.

General Information

Status
Published
Public Enquiry End Date
14-Nov-2017
Publication Date
17-Sep-2019
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
29-Aug-2019
Due Date
03-Nov-2019
Completion Date
18-Sep-2019

Relations

Buy Standard

Standard
EN 12504-1:2019
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 12504-1:2019
01-oktober-2019
Nadomešča:
SIST EN 12504-1:2009
Preskušanje betona v konstrukcijah - 1. del: Izvrtani preskušanci - Jemanje,
pregled in tlačni preskus
Testing concrete in structures - Part 1: Cored specimens - Taking, examining and testing
in compression
Prüfung von Beton in Bauwerken - Teil 1: Bohrkernproben - Herstellung, Untersuchung
und Prüfung der Druckfestigkeit
Essais pour béton dans les structures - Partie 1 : Carottes - Prélèvement, examen et
essais en compression
Ta slovenski standard je istoveten z: EN 12504-1:2019
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
SIST EN 12504-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 12504-1:2019

---------------------- Page: 2 ----------------------
SIST EN 12504-1:2019


EN 12504-1
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2019
EUROPÄISCHE NORM
ICS 91.100.30 Supersedes EN 12504-1:2009
English Version

Testing concrete in structures - Part 1: Cored specimens -
Taking, examining and testing in compression
Essais pour béton dans les structures - Partie 1 : Prüfung von Beton in Bauwerken - Teil 1:
Carottes - Prélèvement, examen et essais en Bohrkernproben - Herstellung, Untersuchung und
compression Prüfung der Druckfestigkeit
This European Standard was approved by CEN on 29 April 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12504-1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 12504-1:2019
EN 12504-1:2019 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Apparatus . 4
6 Taking cores . 5
6.1 General . 5
6.2 Location . 5
6.3 Drilling . 5
6.4 Length of cores . 5
6.5 Marking and identification . 5
7 Examination . 6
7.1 Visual inspection . 6
7.2 Measurements . 6
8 Preparation of cores. 6
8.1 General . 6
8.2 Length/diameter ratios . 7
8.3 Tolerances . 7
9 Compression test . 7
9.1 Storage . 7
9.2 Testing . 7
10 Expression of results . 8
11 Test report . 8
12 Precision . 8
Annex A The effect of aggregate size and core diameter on core specimen strength . 9
Bibliography . 10

2

---------------------- Page: 4 ----------------------
SIST EN 12504-1:2019
EN 12504-1:2019 (E)
European foreword
This document (EN 12504-1:2019) has been prepared by Technical Committee CEN/TC 104 “Concrete
and related products”, the secretariat of which is held by SN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2019, and conflicting national standards
shall be withdrawn at the latest by December 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12504-1:2009.
It is recognized good practice to include measurement of density prior to the determination of
compressive strength, as a check on compaction of the concrete.
In drafting the standard consideration has been given to the results of the research programme, part
funded by the EC under the Measurement and Testing Programme, contract MAT1-CT94-0043.
The standard includes simple guidance on the process of taking cores, but does not consider a sampling
plan. It also provides procedures for visual examination and compressive strength testing, but not the
interpretation of the results.
This standard is one of a series on testing concrete.
EN 12504, Testing concrete in structures, consists of the following parts:
— Part 1: Cored specimens – Taking, examining and testing in compression;
— Part 2: Non-destructive testing – Determination of rebound number;
— Part 3: Determination of pull-out force;
— Part 4: Determination of ultrasonic pulse velocity.
This edition includes the following significant technical changes with respect to EN 12504-1:2009:
a) editorial revisions;
b) measurement of core dimensions;
c) core samples to be tested in an in situ or wet conditions;
d) procedures for preparation of specimens prior to testing.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------
SIST EN 12504-1:2019
EN 12504-1:2019 (E)
1 Scope
This document specifies a method for taking cores from hardened concrete, their examination,
preparation for testing and determination of compressive strength.
This document does not give guidance on the decision to drill cores or on the locations for drilling.
This document does not provide procedures for interpreting the core strength results.
For the assessment of in situ compressive strength in structures and precast concrete components,
EN 13791 may be used.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 12390-1, Testing hardened concrete — Part 1: Shape, dimensions and other requirements for
specimens and moulds
EN 12390-3:2019, Testing hardened concrete — Part 3: Compressive strength of test specimens
EN 12390-4, Testing hardened concrete — Part 4: Compressive strength — Specification for testing
machines
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
4 Principle
Cores extracted using a core drill are carefully examined, prepared by grinding or capping and tested in
compression using standard procedures.
5 Apparatus
5.1 Core dri
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.