SIST EN 60332-1-3:2005

Tests on electric and optical fibre cables under fire conditions -- Part 1-3: Test for vertical flame propagation for a single insulated wire or cable - Procedure for determination of flaming droplets/particles

This part of IEC 60332 specifies a test procedure for assessment of falling flaming droplets/
particles when a single vertical electrical insulated conductor or cable, or optical fibre cable, is
subjected to defined fire conditions.
NOTE 1 Testing to IEC 60332-1-3 may be performed simultaneously with that to IEC 60332-1-2, if required.
Recommended requirements for performance are given in Annex A.
IEC 60332-1-3 specifies the use of a 1 kW pre-mixed flame and is for general use, except that
the procedure specified may not be suitable for the testing of small single insulated conductors
or cables of less than 0,5 mm2 total cross-section because the conductor melts before the test
is completed, or for the testing of small optical fibre cables because the cable is broken before
the test is completed.

Prüfungen an Kabeln, isolierten Leitungen und Glasfaserkabeln im Brandfall -- Teil 1-3: Prüfung der vertikalen Flammenausbreitung an einer Ader, einer isolierten Leitung oder einem Kabel - Prüfverfahren zur Bewertung fallender brennender Tropfen/Teile

Essais des câbles électriques et à fibres optiques soumis au feu -- Partie 1-3: Essai de propagation verticale de la flamme sur conducteur ou câble isolé - Procédure pour la détermination des particules/gouttelettes enflammées

Spécifie une méthode d'essai pour évaluer les particules/gouttelettes enflammées tombant d'un conducteur ou câble, ou d'un câble à fibres optiques, lorsqu'il est soumis au feu dans des conditions définies. NOTE - L'essai de la EN 60332-1-3 peut être réalisé simultanément avec celui de la EN 60332-1-2, si demandé. L'Annexe A donne les recommandations pour les prescriptions de performance. La EN 60332-1-3 donne des précisions sur l'emploi d'une flamme de type à prémélange de 1 kW et est destinée à un usage général. Cependant la procédure spécifiée peut ne pas convenir pour l'essai sur conducteur ou câble de section totale inférieure à 0,5 mm2, car l'âme peut fondre avant la fin de l'essai, ou bien encore pour l'essai de petits câbles à fibres optiques parce que le câble est rompu avant la fin de l'essai. A le statut d'une publication groupée de sécurité conformément au Guide CEI 104.

Preskusi na električnih kablih in kablih iz optičnih vlaken v požarnih razmerah – 1-3. del: Preskus navpičnega širjenja ognja po posamezni izolirani žici ali kablu – Postopek za ugotavljanje gorečih kapljic/delcev

Ta del standarda IEC 60332 določa preskusni postopek za ocenitev padajočih gorečih kapljic/delcev, kadar je enojni navpični električni izolirani vodnik/kabel ali kabel iz optičnih vlaken izpostavljen določenim požarnim razmeram.
OPOMBA 1: Po potrebi se lahko preskušanje v skladu z določili standarda IEC 60332-1-3 izvaja hkrati s preskušanjem v skladu z določili standarda IEC 60332-1-2.
Priporočene zahteve glede lastnosti so navedene v dodatku A.
IEC 60332-1-3 določa uporabo predmešanega plamena 1 kW in je namenjen za splošno uporabo, vendar predpisani postopek morda ne bo primeren za preskušanje posameznih tankih izoliranih vodnikov ali kablov s skupnim presekom manj kot 0,5 mm2, ker se vodnik stali, preden je preskus dokončan, ali za preskušanje tankih kablov iz optičnih vlaken, ker se kabel zlomi, preden je preskus dokončan.

General Information

• Status: Published
• Publication Date: 28-Feb-2005
• ICS: 13.220.40 - Ignitability and burning behaviour of materials and products
• ICS: 29.060.20 - Cables
• ICS: 33.180.10 - Fibres and cables
• Technical Committee: IEKA - Electric cables
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Mar-2005
• Due Date: 01-Mar-2005
• Completion Date: 01-Mar-2005
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Directive: 73/23/EEC - Electrical equipment designed for use within certain voltage limits
• Directive: TP103 - Pravilnik o železniškem telekomunikacijskem omrežju
• Ref Project: EN 60332-1-3:2004 - Tests on electric and optical fibre cables under fire conditions - Part 1-3: Test for vertical flame propagation for a single insulated wire or cable - Procedure for determination of flaming droplets/particles

Relations

• Amended By: SIST EN 60332-1-3:2005/A1:2015 - Tests on electric and optical fibre cables under fire conditions - Part 1-3: Test for vertical flame propagation for a single insulated wire or cable - Procedure for determination of flaming droplets/particles
• Effective Date: 28-Jan-2023
• Amended By: SIST EN 60332-1-3:2005/A1:2015 - Tests on electric and optical fibre cables under fire conditions - Part 1-3: Test for vertical flame propagation for a single insulated wire or cable - Procedure for determination of flaming droplets/particles
• Effective Date: 01-Dec-2015

Standards Content (Sample)

SLOVENSKI SIST EN 60332-1-3:2005

STANDARD
marec 2005
Preskusi na električnih kablih in kablih iz optičnih vlaken v požarnih razmerah
– 1-3. del: Preskus navpičnega širjenja ognja po posamezni izolirani žici ali
kablu – Postopek za ugotavljanje gorečih kapljic/delcev
Tests on electric and optical fibre cables under fire conditions – Part 1-3: Test for
vertical flame propagation for a single insulated wire or cable – Procedure for
determination of flaming droplets/particles (IEC 60332-1-3:2004)
ICS 13.220.40; 29.060.20; 33.180.10 Referenčna številka
SIST EN 60332-1-3:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 60332-1-3
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2004

ICS 13.220.40; 29.020; 29.060.20


English version


Tests on electric and optical fibre cables under fire conditions
Part 1-3: Test for vertical flame propagation
for a single insulated wire or cable -
Procedure for determination of flaming droplets/particles
(IEC 60332-1-3:2004)


Essais des câbles électriques  Prüfungen an Kabeln, isolierten Leitungen
et à fibres optiques soumis au feu und Glasfaserkabeln im Brandfall
Partie 1-3: Essai de propagation verticale Teil 1-3: Prüfung der vertikalen
de la flamme sur conducteur Flammenausbreitung an einer Ader,
ou câble isolé - einer isolierten Leitung oder einem Kabel -
Procédure pour la détermination Prüfverfahren zur Bewertung fallender
des particules/gouttelettes enflammées brennender Tropfen/Teile
(CEI 60332-1-3:2004) (IEC 60332-1-3:2004)





This European Standard was approved by CENELEC on 2004-09-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60332-1-3:2004 E

---------------------- Page: 2 ----------------------

EN 60332-1-3:2004 - 2 -
Foreword
The text of document 20/698/FDIS, future edition 1 of IEC 60332-1-3, prepared by IEC TC 20, Electric
cables, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60332-1-3 on 2004-09-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2005-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-09-01
Annex ZA has been added by CENELEC
__________
Endorsement notice
The text of the International Standard IEC 60332-1-3:2004 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60332-1-2 NOTE Harmonized as EN 60332-1-2:2004 (not modified).
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60332-1-3:2004
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60332-1-1 - Tests on electric and optical fibre cables EN 60332-1-1 2004
under fire conditions
Part 1-1: Test for vertical flame
propagation for a single insulated wire or
cable – Apparatus

1)
IEC Guide 104 - The preparation of safety publications - -
and the use of basic safety publications
and group safety publications

1) 2)
ISO 187 - Paper, board and pulps EN 20187 1993
Standard atmosphere for conditioning and
testing and procedure for monitoring the
atmosphere and conditioning of samples




1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 4 ----------------------

NORME CEI
INTERNATIONALE
IEC



60332-1-3
INTERNATIONAL


Première édition
STANDARD

First edition

2004-07


PUBLICATION GROUPÉE DE SÉCURITÉ
GROUP SAFETY PUBLICATION
Essais des câbles électriques
et à fibres optiques soumis au feu –
Partie 1-3:
Essai de propagation verticale de la flamme
sur conducteur ou câble isolé –
Procédure pour la détermination des
particules/gouttelettes enflammées

Tests on electric and optical fibre cables
under fire conditions –
Part 1-3:
Test for vertical flame propagation
for a single insulated wire or cable –
Procedure for determination of
flaming droplets/particles

© IEC 2004 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photo-copie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
CODE PRIX
L
Commission Electrotechnique Internationale
PRICE CODE
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 5 ----------------------

60332-1-3 © IEC:2004 – 3 –
CONTENTS
FOREWORD.5

1 Scope.9
2 Normative references.9
3 Terms and definitions .9
4 Test apparatus.11
4.1 General.11
4.2 Ignition source.11
4.3 Filter paper.11
5 Procedure.11
5.1 Sample.11
5.2 Conditioning .11
5.3 Positioning of test piece and filter paper.11
5.4 Flame application .13
6 Evaluation of test results.13

Annex A (informative) Recommended performance requirements .19

21
Bibliography .

---------------------- Page: 6 ----------------------

60332-1-3 © IEC:2004 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES
UNDER FIRE CONDITIONS –

Part 1-3: Test for vertical flame propagation for a single insulated
wire or cable – Procedure for determination of flaming droplets/particles


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible f
...