SIST EN 61196-10:2016
(Main)Coaxial communication cables - Part 10: Sectional specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric (IEC 61196-10:2014)
Coaxial communication cables - Part 10: Sectional specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric (IEC 61196-10:2014)
This part of IEC 61196 applies to semi-rigid coaxial communication cables with
polytetrafluoroethylene (PTFE) dielectric and tubular outer conductor. These cables are
intended for use in microwave and wireless equipments or other signal transmission
equipments or units at frequencies above 500 MHz. It is to be read in conjunction with
IEC 61196-1:2005.
Koaxiale Kommunikationskabel - Teil 10: Rahmenspezifikation für halb-starre Kabel mit Polytetrafluorethylen- (PTFE-)Isolation
Câbles coaxiaux de communication - Partie 10: Spécification intermédiaire relative aux câbles semi-rigides avec diélectrique en polytétrafluoroéthylène (PTFE)
L'IEC 61196-10:2014 s'applique aux câbles coaxiaux semi-rigides de communication comportant un diélectrique en polytétrafluoroéthylène (PTFE) et un conducteur extérieur tubulaire. Ces câbles sont destinés à être utilisés dans les équipements à microondes et sans fil ou dans d'autres équipements ou unités de transmission de signal, à des fréquences supérieures à 500 MHz.
Le contenu du corrigendum publié en février 2016 est inclus dans ce
document.
Cette publication doit être lue conjointement avec la IEC 61196-1:2005.
Komunikacijski koaksialni kabli - 10. del: Področna specifikacija poltogih kablov s politetrafluoretilenskim (PTFE) dielektrikom (IEC 61196-10:2014)
Ta del standarda IEC 61196 velja za poltoge komunikacijske koaksialne kable s politetrafluoretilenskim (PTFE) dielektrikom in zunanjim vodnikom iz cevi. Ti kabli so namenjeni za uporabo v mikrovalovni in brezžični opremi, drugi opremi za prenos signalov ali enotah, ki delujejo na frekvencah, višjih od 500 MHz. Standard je treba brati v povezavi s standardom IEC 61196-1:2005.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61196-10:2016
01-april-2016
1DGRPHãþD
SIST EN 61196-2:2004
.RPXQLNDFLMVNLNRDNVLDOQLNDEOLGHO 3RGURþQDVSHFLILNDFLMDSROWRJLKNDEORYV
SROLWHWUDIOXRUHWLOHQVNLP 37)( GLHOHNWULNRP ,(&
Coaxial communication cables - Part 10: Sectional specification for semi-rigid cables with
polytetrafluoroethylene (PTFE) dielectric (IEC 61196-10:2014)
Koaxiale Kommunikationskabel - Teil 10: Rahmenspezifikation für halb-starre Kabel mit
Polytetrafluorethylen- (PTFE-)Isolation
Câbles coaxiaux de communication - Partie 10: Spécification intermédiaire relative aux
câbles semi-rigides avec diélectrique en polytétrafluoroéthylène (PTFE)
Ta slovenski standard je istoveten z: EN 61196-10:2016
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
SIST EN 61196-10:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 61196-10:2016
---------------------- Page: 2 ----------------------
SIST EN 61196-10:2016
EUROPEAN STANDARD EN 61196-10
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2016
ICS 33.120.10 Supersedes EN 61196-2:2003
English Version
Coaxial communication cables - Part 10: Sectional specification
for semi-rigid cables with polytetrafluoroethylene (PTFE)
dielectric
(IEC 61196-10:2014)
Câbles coaxiaux de communication - Partie 10: Koaxiale Kommunikationskabel - Teil 10:
Spécification intermédiaire relative aux câbles semi-rigides Rahmenspezifikation für halb-starre Kabel mit
avec diélectrique en polytétrafluoroéthylène (PTFE) Polytetrafluorethylen- (PTFE-)Isolation
(IEC 61196-10:2014) (IEC 61196-10:2014)
This European Standard was approved by CENELEC on 2015-10-05. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61196-10:2016 E
---------------------- Page: 3 ----------------------
SIST EN 61196-10:2016
EN 61196-10:2016
European foreword
The text of document 46A/1213/FDIS, future edition 1 of IEC 61196-10, prepared by SC 46A "Coaxial
cables" of IEC/TC 46 "Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive
components and accessories" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 61196-10:2016.
The following dates are fixed:
• latest date by which the document has to be (dop) 2016-07-22
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2019-01-22
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61196-2:2003.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61196-10:2014 was approved by CENELEC as a European
Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN 61196-10:2016
EN 61196-10:2016
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 1988 Environmental testing -- Part 1: General EN 60068-1 1994
and guidance
+ A1 1992 - -
IEC 61169-4 - Radio-frequency connectors -- Part 4: R.F. - -
coaxial connectors with inner diameter of
outer conductor 16 mm (0,63 in) with screw
lock - Characteristic impedance 50 ohms
(type 7-16)
IEC 61196-1 2005 Coaxial communication cables - Part 1: - -
Generic specification - General, definitions
and requirements
IEC 61196-1-1 - Coaxial communication cables - Part 1-1: - -
Capability approval for coaxial cables
IEC 61196-1-101 - Coaxial communication cables - Part 1- - -
101: Electrical test methods - Test for
conductor DC resistance of cable
IEC 61196-1-102 - Coaxial communication cables - Part 1- - -
102: Electrical test methods - Test for
insulation resistance of cable dielectric
IEC 61196-1-103 - Coaxial communication cables - Part 1- - -
103: Electrical test methods - Test for
capacitance of cable
IEC 61196-1-105 - Coaxial communication cables - Part 1- - -
105: Electrical test methods - Test for
withstand voltage of cable dielectric
IEC 61196-1-108 - Coaxial communication cables - Part 1- - -
108: Electrical test methods - Test for
characteristic impedance, phase and group
delay, electrical length and propagation
velocity
IEC 61196-1-112 - Coaxial communication cables - Part 1- - -
112: Electrical test methods - Test for
return loss (uniformity of impedance)
IEC 61196-1-113 - Coaxial communication cables - Part 1- - -
113: Electrical test methods - Test for
attenuation constant
IEC 61196-1-115 - Coaxial communication cables - Part 1- - -
115: Electrical test methods - Test for
regularity of impedance (pulse/step
function return loss)
IEC 61196-1-301 - Coaxial communication cables -- Part 1- - -
301: Mechanical test methods - Test for
ovality
IEC 61196-1-302 - Coaxial communication cables - Part 1- - -
302: Mechanical test methods - Test for
eccentricity
3
---------------------- Page: 5 ----------------------
SIST EN 61196-10:2016
EN 61196-10:2016
IEC 61196-1-313 - Coaxial communication cables - Part 1- - -
313: Mechanical test methods - Adhesion
of dielectric and sheath
IEC 61196-1-314 - Coaxial communication cables - Part 1- - -
314: Mechanical test methods - Test for
bending
IEC 61196-1-318 - Coaxial communication cables - Part 1- - -
318: Mechanical test methods - Heat
performance tests
IEC 62037-4 2012 Passive RF and microwave devices, EN 62037-4 2012
intermodulation level measurement -- Part
4: Measurement of passive intermodulation
in coaxial cables
IEC 62230 2006 Electric cables - Spark-test method EN 62230 2007
ISO 2859-1 1999 Sampling procedures for inspection by - -
attributes - Part 1: Sampling schemes
indexed by acceptance quality limit (AQL)
for lot-by-lot inspection
4
---------------------- Page: 6 ----------------------
SIST EN 61196-10:2016
IEC 61196-10
®
Edition 1.0 2014-09
INTERNATIONAL
STANDARD
Coaxial communication cables –
Part 10: Sectional specification for semi-rigid cables with
polytetrafluoroethylene (PTFE) dielectric
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
Q
ICS 33.120.10 ISBN 978-2-8322-1866-2
Warning! Make sure that you obtained this publication from an authorized distributor.
® Registered trademark of the International Electrotechnical Commission
---------------------- Page: 7 ----------------------
SIST EN 61196-10:2016
– 2 – IEC 61196-10:2014 © IEC 2014
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Materials and cable construction . 6
4.1 Cable construction . 6
4.2 Inner conductor . 6
4.3 Dielectric . 7
4.4 Outer conductor . 7
4.5 Sheath (when applicable) . 7
5 Standard rating and characteristics . 7
5.1 Characteristic impendence . 7
5.2 Rated temperature range . 7
6 Identification, marking and labeling . 8
6.1 Cable identification . 8
6.1.1 Type name . 8
6.1.2 Variants . 8
6.2 IEC marking . 8
6.3 Labelling . 8
7 Requirements of finished cables . 8
7.1 General . 8
7.2 Electrical requirements (see Table 1) . 8
7.3 Environmental requirements (see Table 2) . 10
7.4 Mechanical requirements (see Table 3) . 10
8 Delivery and storage . 11
Annex A (informative) Quality assessment . 12
A.1 General . 12
A.2 Qualification approval and its maintenance . 12
A.2.2 Capability approval . 14
A.2.3 Quality conformance inspection . 14
A.2.4 Periodic inspection . 16
Bibliography . 17
Table 1 – Electrical requirements . 9
Table 2 – Environmental requirements . 10
Table 3 – Mechanical requirements. 10
Table A.1 – Qualification inspection . 13
Table A.2 – Quality conformance inspection . 15
---------------------- Page: 8 ----------------------
SIST EN 61196-10:2016
IEC 61196-10:2014 © IEC 2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COAXIAL COMMUNICATION CABLES –
Part 10: Sectional specification for semi-rigid cables
with polytetrafluoroethylene (PTFE) dielectric
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61196-10 has been prepared by subcommittee 46A: Coaxial
cables, of IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and
microwave passive components and accessories.
This first edition cancels and replaces IEC 61196-2 published in 1995. This edition constitutes
a technical revision.
The text of this standard is based on the following documents:
FDIS Report on voting
46A/1213/FDIS 46A/1232/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
---------------------- Page: 9 ----------------------
SIST EN 61196-10:2016
– 4 – IEC 61196-10:2014 © IEC 2014
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This publication is to be read in conjunction with IEC 61196-1:2005.
A list of all parts in the IEC 61196 series, published under the general title Coaxial
communication cables, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
---------------------- Page: 10 ----------------------
SIST EN 61196-10:2016
IEC 61196-10:2014 © IEC 2014 – 5 –
COAXIAL COMMUNICATION CABLES –
Part 10: Sectional specification for semi-rigid cables
with polytetrafluoroethylene (PTFE) dielectric
1 Scope
This part of IEC 61196 applies to semi-rigid coaxial communication cables with
polytetrafluoroethylene (PTFE) dielectric and tubular outer conductor. These cables are
intended for use in microwave and wireless equipments or other signal transmission
equipments or units at frequencies above 500 MHz. It is to be read in conjunction with
IEC 61196-1:2005.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60068-1:1988, Environmental testing – Part 1: General and guidance
IEC 60068-1:1988/AMD 1:1992
IEC 61169-4, Radio-frequency connectors – Part 4: RF coaxial connectors with inner diameter
of outer conductor 16 mm (0,63 in) with screw lock – Characteristic impedance 50 Ω
(type 7-16)
IEC 61196-1:2005, Coaxial communication cables – Part 1: Generic specification – General,
definitions and requirements
IEC 61196-1-1, Coaxial communication cables – Part 1-1: Capability approval for coaxial
cables
IEC 61196-1-101, Coaxial communication cables – Part 1-101: Electrical test methods – Test
for conductor d.c. resistance of cable
IEC 61196-1-102, Coaxial communication cables – Part 1-102: Electrical test methods – Test
for insulation resistance of cable dielectric
IEC 61196-1-103, Coaxial communication cables – Part 1-103: Electrical test methods – Test
for capacitance of cable
IEC 61196-1-105, Coaxial communication cables – Part 1-105: Electrical test methods – Test
for withstand voltage of cable dielectric
IEC 61196-1-108, Coaxial communication cables – Part 1-108: Electrical test methods – Test
for characteristic impedance, phase and group delay, electrical length and propagation
velocity
IEC 61196-1-112, Coaxial communicat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.