SIST EN 60684-3-116:2012

Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheets 116 and 117: Extruded polychloroprene, general purpose

This part of IEC 60684 gives the requirements for non-heat-shrinkable sleeving, extruded from compounds based on polychloroprene elastomer.This sleeving has been found suitable for temperatures up to 95 ?C. Sleeving of this type is normally available with internal diameters up to 25 mm, and in the following opaque colours: black, brown, red, orange, yellow, green, blue, violet, grey, white and pink. Sizes or colours other than those specifically listed in this standard may be available as custom items. These items shall be considered to comply with this standard if they comply with the other property requirements listed in Table 2. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in the application and not based on the specification alone.

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blätter 116 bis 117: Extrudierte Polychloroprenschläuche, Standardtyp

Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuilles 116 & 117: Polychloroprène extrudé - Utilisation générale

La CEI 60684-3-116:2010 donne les exigences relatives aux gaines non thermorétractables, extrudées à partir de composés à base d'élastomère polychloroprène. Ces gaines conviennent pour des températures jusqu'à 95 °C. Les gaines de ce type sont généralement proposées avec des diamètres intérieurs allant jusqu'à 25 mm et dans les couleurs opaques suivantes: noir, brun, rouge, orange, jaune, vert, bleu, violet, gris, blanc et rose. D'autres dimensions et d'autres couleurs que celles spécifiquement indiquées dans cette norme peuvent être proposées comme articles spéciaux. Cette édition contient quatre exigences supplémentaires:  - propagation des ruptures;  - extension en circonférence;  - tension de tenue et choc thermique.

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne vrste cevi - 116. in 117. list: Ekstrudirani polipropilen za splošne namene

Ta del IEC 60684 podaja zahteve za toplotno neskrčljive cevi, ekstrudirane iz spojin na osnovi polikloroprenskega elastomera. Take cevi so dokazano primerne za temperature do 95 °C. Tovrstne cevi so običajno na voljo z notranjim premerom do 25 mm in v naslednjih neprozornih barvah: črna, rjava, rdeča, oranžna, rumena, zelena, modra, vijoličasta, siva, bela in rožnata. Velikosti ali barve, ki niso navedene v tem standardu, so lahko na voljo na zahtevo. Ti predmeti so skladni s tem standardom, če izpolnjujejo zahteve glede lastnosti, navedene v preglednici 2. Materiali, skladni s to specifikacijo, ustrezajo vzpostavljenim ravnem delovanja. Vendar mora uporabnik material za določeno uporabo izbrati na podlagi dejanskih zahtev za ustrezno delovanje pri taki uporabi, ne le na podlagi same specifikacije.

General Information

• Status: Published
• Publication Date: 22-Nov-2011
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: IIZS - Insulating materials and systems
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 16-Nov-2011
• Due Date: 21-Jan-2012
• Completion Date: 23-Nov-2011
• Ref Project: EN 60684-3-116:2011 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 116 and 117: Extruded polychloroprene, general purpose

Relations

• Replaces: SIST EN 60684-3-116 & 117:2004 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheets 116 and 117: Extruded polychloroprene - General purpose
• Effective Date: 29-Jan-2023
• Revised: SIST EN 60684-3-116 & 117:2004 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheets 116 and 117: Extruded polychloroprene - General purpose
• Effective Date: 23-Jul-2013
• Revised: oSIST prEN IEC 60684-3-116:2023 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 116 and 117: Extruded polychloroprene, general purpose
• Effective Date: 26-Jul-2021

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60684-3-116:2012
01-januar-2012
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne vrste cevi - 116. in 117.
list: Ekstrudirani polipropilen za splošne namene
Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheets
116 and 117: Extruded polychloroprene, general purpose
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blätter 116 bis
117: Extrudierte Polychloroprenschläuche, Standardtyp
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines -
Feuilles 116 & 117: Polychloroprène extrudé - Utilisation générale
Ta slovenski standard je istoveten z: EN 60684-3-116:2011
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
SIST EN 60684-3-116:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60684-3-116:2012

---------------------- Page: 2 ----------------------

SIST EN 60684-3-116:2012

EUROPEAN STANDARD
EN 60684-3-116

NORME EUROPÉENNE
November 2011
EUROPÄISCHE NORM

ICS 29.035.20 Supersedes EN 60684-3-116 & 117:2003


English version


Flexible insulating sleeving -
Part 3: Specifications for individual types of sleeving -
Sheets 116 and 117: Extruded polychloroprene, general purpose
(IEC 60684-3-116:2010)


Gaines isolantes souples -  Isolierschläuche -
Partie 3: Spécifications pour types Teil 3: Anforderungen für einzelne
particuliers de gaines - Schlauchtypen -
Feuilles 116 à 117: Polychloroprène Blätter 116 bis 117: Extrudierte
extrudé, utilisation générale Polychloroprenschläuche, Standardtyp
(CEI 60684-3-116:2010) (IEC 60684-3-116:2010)





This European Standard was approved by CENELEC on 2010-07-20. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-116:2011 E

---------------------- Page: 3 ----------------------

SIST EN 60684-3-116:2012
EN 60684-3-116:2011 - 2 -
Foreword
The text of document 15/560/FDIS, future edition 3 of IEC 60684-3-116, prepared by IEC TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60684-3-116:2011.

The following dates are fixed:
(dop) 2012-05-11
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2013-07-20
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This document supersedes EN 60684-3-116&117:2003.
EN 60684-3-116:2011 includes requirements four new tests: tear propagation; circumferential extension;
voltage proof and thermal shock.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.

Endorsement notice
The text of the International Standard IEC 60684-3-116:2010 was approved by CENELEC as a European
Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 60684-3-116:2012
- 3 - EN 60684-3-116:2011
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60684-1 2003 Flexible insulating sleeving - EN 60684-1 2003
Part 1: Definitions and general requirements


IEC 60684-2 1997 Flexible insulating sleeving - EN 60684-2 1997
+ A1 2003 Part 2: Methods of test + A1 2003
+ A2 2005 + A2 2005


IEC 60684-2 2011 Flexible insulating sleeving - EN 60684-2 2011
Part 2: Methods of test


IEC 60757 1983 Code for designation of colours HD 457 S1 1985

---------------------- Page: 5 ----------------------

SIST EN 60684-3-116:2012

---------------------- Page: 6 ----------------------

SIST EN 60684-3-116:2012
IEC 60684-3-116
®
Edition 3.0 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Flexible insulating sleeving –
Part 3: Specifications for individual types of sleeving –
Sheets 116 and 117: Extruded polychloroprene, general purpose

Gaines isolantes souples –
Partie 3: Spécifications pour types particuliers de gaines –
Feuilles 116 à 117: Polychloroprène extrudé, utilisation générale


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
J
CODE PRIX
ICS 29.035.20 ISBN 978-2-88910-966-1
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60684-3-116:2012
– 2 – 60684-3-116 © IEC:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references.6
3 Designation .6
4 Requirements .7
5 Sleeving conformance.7

Table 1 – Dimensional requirements.7
Table 2 – Property requirements .8

---------------------- Page: 8 ----------------------

SIST EN 60684-3-116:2012
60684-3-116 © IEC:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FLEXIBLE INSULATING SLEEVING –

Part 3: Specifications for individual types of sleeving –
Sheets 116 and 117: Extruded polychloroprene, general purpose


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the
...