SIST EN 1301-3:2008

Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions

This European Standard prEN 1301 specifies the mechanical properties of aluminium and aluminium alloy drawn wire of general engineering applications (except aeronautical rivets).
It applies to drawn wires, except for electrical or welding purposes.
It does not apply to drawing stock.
The designation of aluminium and aluminium alloys, their chemical composition and the temper designations used in this standard are in accordance with EN 573- 3 and EN 515 respectively.
These aluminium and aluminium alloys correspond to the alloys produced in large quantities in Europe (class A as defined in 573-4).

Aluminium und Aluminiumlegierungen - Gezogene Drähte - Teil 3: Grenzabmaße

Dieses Dokument legt die Grenzabmaße für gezogene Drähte aus Aluminium und Aluminiumlegierungen für allgemeine Anwendungen fest (ausgenommen Anwendungen in der Luftfahrt) und gilt für Durchmesser,
Dicken, Breiten oder Schlüsselweiten bis 20 mm.
Es gilt für gezogene Drähte, ausgenommen Drähte für elektrotechnische oder schweißtechnische Anwen¬dungen.
Es gilt nicht für Vordraht.

Aluminium et alliages d'aluminium - Fil étiré - Partie 3: Tolérances sur dimensions

Le présent document spécifie les tolérances sur dimensions du fil étiré en aluminium ou en alliage
d'aluminium destiné à des applications mécaniques (à l'exception des rivets utilisés en aéronautique), et
correspondant à des diamètres, des épaisseurs ou des largeurs entre plats inférieures ou égales à 20 mm.
Il s'applique aux fils étirés, à l’exception des applications en électricité ou en soudage.
Il ne s’applique pas aux fils machine.

Aluminij in aluminijeve zlitine - Vlečena žica - 3. del: Tolerance mer

General Information

• Status: Published
• Publication Date: 05-Oct-2008
• ICS: 77.150.10 - Aluminium products
• Technical Committee: INEK - Nonferrous metals
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 24-Sep-2008
• Due Date: 29-Nov-2008
• Completion Date: 06-Oct-2008
• Ref Project: EN 1301-3:2008 - Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions

Relations

• Replaces: SIST EN 1301-3:1998 - Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions
• Effective Date: 01-Nov-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium und Aluminiumlegierungen - Gezogene Drähte - Teil 3: GrenzabmaßeAluminium et alliages d'aluminium - Fil étiré - Partie 3: Tolérances sur dimensionsAluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions77.150.10Aluminijski izdelkiAluminium productsICS:Ta slovenski standard je istoveten z:EN 1301-3:2008SIST EN 1301-3:2008en,fr,de01-november-2008SIST EN 1301-3:2008SLOVENSKI
STANDARDSIST EN 1301-3:19981DGRPHãþD



SIST EN 1301-3:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1301-3September 2008ICS 77.150.10Supersedes EN 1301-3:1997
English VersionAluminium and aluminium alloys - Drawn wire - Part 3:Tolerances on dimensionsAluminium et alliages d'aluminium - Fil étiré - Partie 3:Tolérances sur dimensionsAluminium und Aluminiumlegierungen - Gezogene Drähte -Teil 3: GrenzabmaßeThis European Standard was approved by CEN on 16 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1301-3:2008: ESIST EN 1301-3:2008



EN 1301-3:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Tolerances on dimensions.4 3.1 General.4 3.2 Round wire.5 3.3 Square and hexagonal wire.5 3.4 Rectangular wire.6
SIST EN 1301-3:2008



EN 1301-3:2008 (E) 3 Foreword This document (EN 1301-3:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2009, and conflicting national standards shall be withdrawn at
...