Household and similar electrical appliances - Safety - Part 2-34: Particular requirements for motor-compressors

This clause of Part 1 is replaced by the following. This International Standard deals with the safety of sealed (hermetic and semi-hermetic type) motor-compressors, their protection and control systems, if any, which are intended for use in equipment for household and similar purposes and which conform with the standards applicable to such equipment. It applies to motor-compressors tested separately, under the most severe conditions that may be expected to occur in normal use, their rated voltage being not more than 250 V for single-phase motor-compressors and 480 V for other motorcompressors. This standard does not supersede the requirements of standards relevant to the particular appliance in which the motor-compressor is used. However, if the motor-compressor type used complies with this standard, the tests for the motor-compressor specified in the particular appliance standard may not need to be made in the particular appliance or assembly. If the motor-compressor control system is associated with the particular appliance control system, additional tests may be necessary on the final appliance. So far as is practical, this standard deals with the common hazards presented by motorcompressors used in appliances which are encountered by all persons in and around the home. However, it does not in general take into account - the use of appliances by young children or infirm persons without supervision; - playing with the appliances by young children.

Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-34: Besondere Anforderungen für Motorverdichter

Appareils électrodomestiques et analogues - Sécurité - Partie 2-34: Règles particulières pour les motocompresseurs

La CEI 60335-2-34:2012 traite de la sécurité des motocompresseurs étanches (de type hermétique et hermétique accessible) et, le cas échéant, de leurs systèmes de protection et de commande, qui sont destinés à être utilisés sur les appareils électrodomestiques et analogues et qui sont conformes aux normes applicables à de tels matériels. Elle s'applique aux motocompresseurs soumis à essai séparément, dans les conditions les plus sévères qui peuvent se produire en usage normal, la tension assignée n'étant pas supérieure à 250 V pour les motocompresseurs monophasés et à 480 V pour les autres motocompresseurs. Comme exemples d'appareils équipés de motocompresseurs, on peut citer:  - les réfrigérateurs, congélateurs et fabriques de glace (CEI 60335-2-24);  - les climatiseurs, pompes à chaleur électriques et déshumidificateurs (CEI 60335-2-40);  - les distributeurs commerciaux avec ou sans moyen de paiement (CEI 60335-2-75),  - les ensembles montés en usine pour le transfert de chaleur dans des applications de réfrigération, de climatisation ou de chauffage, ou toute combinaison de ces fonctions.  La présente norme ne remplace pas les exigences des normes applicables aux appareils dans lesquels des motocompresseurs sont utilisés. Toutefois, si le type de motocompresseur utilisé est conforme à la présente norme, il est possible que les essais pour les motocompresseurs spécifiés dans les normes relatives aux appareils particuliers n'aient pas besoin d'être effectués sur l'appareil ou l'ensemble particulier. Si le dispositif de commande du motocompresseur est associé au dispositif de commande de l'appareil particulier, des essais complémentaires peuvent être nécessaires sur l'appareil final. Mots clé: motocompresseur, hermétique, hermétique accessible

Gospodinjski in podobni električni aparati - Varnost - 2-34. del: Posebne zahteve za motorne kompresorje (IEC 60335-2-34:2012)

To točko 1. dela nadomešča naslednje besedilo. Ta mednarodni standard obravnava varnost zatesnjenih motornih kompresorjev (hermetičnega ali polhermetičnega tipa) ter njihovih zaščitnih in nadzornih sistemov, če so nameščeni, ki so namenjeni za uporabo v opremi za gospodinjstvo in podobne namene ter ki so v skladu s standardi, ki veljajo za takšno opremo. Velja za motorne kompresorje, preskušene ločeno, v najhujših razmerah, ki se lahko pojavijo pri običajni rabi, pri čemer nazivna napetost enofaznih motorskih kompresorjev ne presega 250 V in nazivna napetost drugih motornih kompresorjev ne presega 480 V. Ta standard ne nadomešča zahtev posameznih standardov, ki zadevajo določene aparate, v katerih je motorni kompresor. Vendar pa v primeru, da uporabljeni tip motorskega kompresorja v zadevnem aparatu ali sestavu ustreza temu standardu, ni potrebno opraviti preskusov za motorni kompresor, navedenih v zadevnem standardu za aparat. Če je kontrolni sistem motornega kompresorja povezan s kontrolnim sistemom zadevne naprave, bodo morda potrebni dodatni preskusi na končnem aparatu. Ta standard v največji možni meri obravnava splošne nevarnosti, ki jih predstavljajo motorski kompresorji v aparatih, s katerimi se srečujejo osebe doma in v okolici doma. Vendar na splošno ne vključuje primerov, ko aparate brez nadzora uporabljajo majhni otroci ali onemogle osebe oziroma ko se otroci igrajo z napravami.

General Information

Status
Published
Publication Date
19-Aug-2013
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
30-Jul-2013
Due Date
04-Oct-2013
Completion Date
20-Aug-2013

Relations

Buy Standard

Standard
EN 60335-2-34:2013
English language
38 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60335-2-34:2013
01-september-2013
1DGRPHãþD
SIST EN 60335-2-34:2003
SIST EN 60335-2-34:2003/A1:2005
SIST EN 60335-2-34:2003/A11:2004
SIST EN 60335-2-34:2003/A2:2009
*RVSRGLQMVNLLQSRGREQLHOHNWULþQLDSDUDWL9DUQRVWGHO3RVHEQH]DKWHYH
]DPRWRUQHNRPSUHVRUMH ,(&
Household and similar electrical appliances - Safety - Part 2-34: Particular requirements
for motor-compressors
Appareils électrodomestiques et analogues - Sécurité - Partie 2-34: Règles particulières
pour les motocompresseurs
Ta slovenski standard je istoveten z: EN 60335-2-34:2013
ICS:
23.140 .RPSUHVRUMLLQSQHYPDWLþQL Compressors and pneumatic
VWURML machines
SIST EN 60335-2-34:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60335-2-34:2013

---------------------- Page: 2 ----------------------

SIST EN 60335-2-34:2013

EUROPEAN STANDARD
EN 60335-2-34

NORME EUROPÉENNE
June 2013
EUROPÄISCHE NORM

ICS 97.040.30 Supersedes EN 60335-2-34:2002 + A1:2005 + A2:2009 + A11:2004


English version


Household and similar electrical appliances -
Safety -
Part 2-34: Particular requirements for motor-compressors
(IEC 60335-2-34:2012)


Appareils électrodomestiques  Sicherheit elektrischer Geräte für den
et analogues - Sécurité - Hausgebrauch und ähnliche Zwecke -
Partie 2-34: Exigences particulières pour Teil 2-34: Besondere Anforderungen
les motocompresseurs für Motorverdichter
(CEI 60335-2-34:2012) (IEC 60335-2-34:2012)





This European Standard was approved by CENELEC on 2012-06-27. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60335-2-34:2013 E

---------------------- Page: 3 ----------------------

SIST EN 60335-2-34:2013
EN 60335-2-34:2013 - 2 -
Foreword
The text of document 61C/508/FDIS, future edition 5 of IEC 60335-2-34, prepared by SC 61C "Safety
of refrigeration appliances for household and commercial use" of IEC/TC 61 "Safety of household and
similar electrical appliances" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60335-2-34:2013.
The following dates are fixed:
(dop) 2013-12-14
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-06-27
standards conflicting with the
document have to be withdrawn

This document supersedes EN 60335-2-34:2002 + A1:2005 + A2:2009 + A11:2004.

EN 60335-2-34:2013 includes the following significant technical changes with respect to
EN 60335-2-34:2002 + A1:2005 + A2:2009 + A11:2004:
- some notes have been deleted or converted to normative text (1, 6.103, 19.14, 22.7, Figure 101);
- manufacturer must declare the type of motor protection used (5.102, 6.104);
- tests to fault-test motor-compressors incorporating electronic circuits introduced (19.11.2,
AA.5);
- application of the EMP tests clarified (19.11.4);
- testing of contactors and relays associated with motor-compressors introduced (19.14);
- Tables 101 and 102 updated and corrected;
- running overload test conditions extended (AA.1, AA.2, AA.3, AA.4, AA.5).

This standard is to be read in conjunction with EN 60335-1:2012 and its amendments.

NOTE 1  When “Part 1” is mentioned in this standard, it refers to EN 60335-1.
This Part 2 supplements or modifies the corresponding clauses in EN 60335-1, so as to convert that
publication into the European Standard: Safety requirements for electrical motor-compressors.
When a particular subclause of Part 1 is not mentioned in this Part 2, that subclause applies as far as
is reasonable. When this standard states "addition", "modification" or "replacement", the relevant text
of Part 1 is to be adapted accordingly.

NOTE 2 The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
– unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101,
including those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.

NOTE 3 The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the
associated noun are also in bold.

---------------------- Page: 4 ----------------------

SIST EN 60335-2-34:2013
- 3 - EN 60335-2-34:2013

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment
Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC).
Endorsement notice
The text of the International Standard IEC 60335-2-34:2012 was approved by CENELEC as a
European Standard without any modification.
The Bibliography of EN 60335-1:2012 is applicable with the addition of the following notes for the standards
indicated:

IEC 60335-2-11 NOTE Harmonised as EN 60335-2-11.
IEC 60335-2-24 NOTE Harmonised as EN 60335-2-24.
IEC 60335-2-40 NOTE Harmonised as EN 60335-2-40.
IEC 60335-2-75 NOTE Harmonised as EN 60335-2-75.
IEC 60335-2-89 NOTE Harmonised as EN 60335-2-89.

---------------------- Page: 5 ----------------------

SIST EN 60335-2-34:2013

---------------------- Page: 6 ----------------------

SIST EN 60335-2-34:2013



IEC 60335-2-34

®


Edition 5.0 2012-05




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Household and similar electrical appliances – Safety –

Part 2-34: Particular requirements for motor-compressors




Appareils électrodomestiques et analogues – Sécurité –

Partie 2-34: Exigences particulières pour les motocompresseurs

















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX W


ICS 97.040.30 ISBN 978-2-83220-085-8



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60335-2-34:2013
– 2 – 60335-2-34 © IEC:2012
CONTENTS

FOREWORD . 4
INTRODUCTION . 7
1 Scope . 9
2 Normative references . 10
3 Terms and definitions . 10
4 General requirement . 11
5 General conditions for the tests . 11
6 Classification . 13
7 Marking and instructions . 14
8 Protection against access to live parts . 14
9 Starting of motor-operated appliances . 14
10 Power input and current . 14
11 Heating . 14
12 Void. 14
13 Leakage current and electric strength at operating temperature . 14
14 Transient overvoltages . 14
15 Moisture resistance . 15
16 Leakage current and electric strength . 15
17 Overload protection of transformers and associated circuits . 15
18 Endurance . 15
19 Abnormal operation . 15
20 Stability and mechanical hazards . 20
21 Mechanical strength . 20
22 Construction . 20
23 Internal wiring . 23
24 Components . 23
25 Supply connection and external flexible cords . 23
26 Terminals for external conductors . 24
27 Provision for earthing . 24
28 Screws and connections . 24
29 Clearances, creepage distances and solid insulation . 24
30 Resistance to heat and fire . 25
31 Resistance to rusting . 25
32 Radiation, toxicity and similar hazards . 25
Annexes . 26
Annex C (normative) Ageing test on motors . 26
Annex D (normative) Thermal motor protectors . 26
Annex AA (normative) Running overload tests for motor-compressors classified as
tested with Annex AA . 27
Bibliography . 35

---------------------- Page: 8 ----------------------

SIST EN 60335-2-34:2013
60335-2-34 © IEC:2012 – 3 –

Figure 101 – Supply circuit for the locked-rotor test of a single-phase motor-
compressor . 25
Figure AA.1 – Substitute refrigeration circuit . 34

Table 101 – Minimum high side test pressures . 21
Table 102 – Minimum low side test pressures . 22
Table AA.1 – Substitute refrigeration circuit conditions for operating under running
overload conditions . 29
Table AA.2 – Substitute refrigeration circuit conditions for operating under maximum
and minimum load conditions . 32

---------------------- Page: 9 ----------------------

SIST EN 60335-2-34:2013
– 4 – 60335-2-34 © IEC:2012
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –

Part 2-34: Particular requirements for motor-compressors


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This part of International Standard IEC 60335 has been prepared by subcommittee 61C:
Safety of refrigeration appliances for household and commercial use, of IEC technical
committee 61: Safety of household and similar electrical appliances.
This fifth edition cancels and replaces the fourth edition published in 2002 including its
Amendment 1 (2004) and its amendment 2 (2008). It constitutes a technical revision.
The principal changes in this edition as compared with the fourth edition of IEC 60335-2-34
are as follows (minor changes are not listed):
– some notes have been deleted or converted to normative text (1, 6.103, 19.14, 22.7,
Figure 101);
– manufacturer must declare the type of motor protection used (5.102, 6.104);
– tests to fault-test motor-compressors incorporating electronic circuits introduced
(19.11.2, AA.5);

---------------------- Page: 10 ----------------------

SIST EN 60335-2-34:2013
60335-2-34 © IEC:2012 – 5 –
– application of the EMP tests clarified (19.11.4);
– testing of contactors and relays associated with motor-compressors introduced (19.14);
– tables 101 and 102 updated and corrected;
– running overload test conditions extended (AA.1, AA.2, AA.3, AA.4, AA.5).
The text of this part of IEC 60335 is based on the following documents:
FDIS Report on voting
61C/508/FDIS 61C/517/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its
amendments. It was established on the basis of the fifth edition (2010) of that standard.
NOTE 1 When “Part 1” is mentioned in this standard, it refers to IEC 60335-1.
This part 2 supplements or modifies the corresponding clauses in IEC 60335-1, so as to
convert that publication into the IEC standard: Safety requirements for electrical motor-
compressors.
When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies
as far as is reasonable. When this standard states "addition", "modification" or "replacement",
the relevant text in Part 1 is to be adapted accordingly.
NOTE 2 The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
– unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including
those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.
NOTE 3 The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in smaller roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the
associated noun are also in bold.
A list of all parts of the IEC 60335 series, under the general title Household and similar
electrical appliances – Safety, can be found on the IEC website.

---------------------- Page: 11 ----------------------

SIST EN 60335-2-34:2013
– 6 – 60335-2-34 © IEC:2012
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE 4 The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation
nationally not earlier than 12 months or later than 36 months from the date of publication.
The following differences exist in the countries indicated below.
– 7.1: The locked-rotor current marking is required for some motor-compressors (USA).
– 22.7: Different test pressures are used (Japan, USA).

---------------------- Page: 12 ----------------------

SIST EN 60335-2-34:2013
60335-2-34 © IEC:2012 – 7 –
INTRODUCTION
It has been assumed in the drafting of this International Standard that the execution of its
provisions is entrusted to appropriately qualified and experienced persons.
This standard recognizes the internationally accepted level of protection against hazards such
as electrical, mechanical, thermal, fire and radiation of appliances when operated as in
normal use taking into account the manufacturer's instructions It also covers abnormal
situations that can be expected in practice and takes into account the way in which
electromagnetic phenomena can affect the safe operation of appliances.
This standard takes into account the requirements of IEC 60364 as far as possible so that
there is compatibility with the wiring rules when the appliance is connected to the supply
mains. However, national wiring rules may differ.
If an appliance within the scope of this standard also incorporates functions that are covered
by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as
far as is reasonable. If applicable, the influence of one function on the other is taken into
account.
When a part 2 standard does not include additional requirements to cover hazards dealt with
in Part 1, Part 1 applies.
NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is
not necessary to specify particular requirements for the appliance in question over and above the general
requirements.
This standard is a product family standard dealing with the safety of appliances and takes
precedence over horizontal and generic standards covering the same subject.
NOTE 2 Horizontal and generic standards covering a hazard are not applicable since they have been taken into
consideration when developing the general and particular requirements for the IEC 60335 series of standards. For
example, in the case of temperature requirements for surfaces on many appliances, generic standards, such as
ISO 13732-1 for hot surfaces, are not applicable in addition to Part 1 or part 2 standards.
An appliance that complies with the text of this standard will not necessarily be considered to
comply with the safety principles of the standard if, when examined and tested, it is found to
have other features that impair the level of safety covered by these requirements.
An appliance employing materials or having forms of construction differing from those detailed
in the requirements of this standard may be examined and tested according to the intent of
the requirements and, if found to be substantially equivalent, may be considered to comply
with the standard.
For motor-compressors, testing in accordance with this standard is an option and cannot be
required as a precondition for testing the complete appliance, for example by reference in
Clause 24 of a part 2 of IEC 60335. However, testing of the appliance should be reduced if an
incorporated motor-compressor including its protection system or control system, if any,
complies with this standard.
If testing of the motor-compressor includes testing in accordance with Annex AA,
temperatures of the motor-compressor windings, housing and other parts related to the
motor-compressor, such as terminals, internal wiring and insulating materials, are not
measured when the complete appliance in which the motor-compressor is used is tested.
These requirements apply to sealed (hermetic and semi-hermetic type) motor-compressors
with their associated starting, cooling capacity control and protection systems, tested
separately under the most severe conditions of the refrigerating system operation which,
within reasonable limits, could occur in the applications for which they are used.

---------------------- Page: 13 ----------------------

SIST EN 60335-2-34:2013
– 8 – 60335-2-34 © IEC:2012
In particular, the construction detail inspection and locked-rotor testing may be done
separately on the motor-compressor, thereby eliminating the need for inspection and testing
when the motor-compressor is applied to many different appliances and factory-built
assemblies.
Operational tests may also be conducted on the motor-compressor separately in certain
circumstances. The specification for this type testing is provided in Annex AA. However, the
tests of the existing standards relevant to the given kind of application, such as IEC 60335-2-
24 and IEC 60335-2-40, may need to be conducted on the final application and used as the
final determination of acceptability.

---------------------- Page: 14 ----------------------

SIST EN 60335-2-34:2013
60335-2-34 © IEC:2012 – 9 –
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –

Part 2-34: Particular requirements for motor-compressors



1 Scope
This clause of Part 1 is replaced by the following.
This International Standard deals with the safety of sealed (hermetic and semi-hermetic type)
motor-compressors, their protection and control systems, if any, which are intended for use
in equipment for household and similar purposes and which conform with the standards
applicable to such equipment. It applies to motor-compressors tested separately, under the
most severe conditions that may be expected to occur in normal use, their rated voltage
being not more than 250 V for single-phase motor-compressors and 480 V for other motor-
compressors.
NOTE 101 Examples of equipment which contain motor-compressors are
– refrigerators, food freezers and ice makers (IEC 60335-2-24);
– air-conditioners, electric heat pumps and dehumidifiers (IEC 60335-2-40);
– commercial dispensing appliances and vending machines (IEC 60335-2-75);
– factory-built assemblies for transferring heat in applications for refrigerating, air-conditioning or heating
purposes or a combination of such purposes.
This standard does not supersede the requirements of standards relevant to the particular
appliance in which the motor-compressor is used. However, if the motor-compressor type
used complies with this standard, the tests for the motor-compressor specified in the
particular appliance standard may not need to be made in the particular appliance or
assembly. If the motor-compressor control system is associated with the particular
appliance control system, additional tests may be necessary on the final appliance.
So far as is practical, this standard deals with the common hazards presented by motor-
compressors used in appliances which are encountered by all persons in and around the
home. However, it does not in general take into account
– the use of appliances by young children or infirm persons without supervision;
– playing with the appliances by young children.
NOTE 102 Attention is drawn to the fact that
– for motor-compressors intended to be used in appliances in vehicles or on board ships, additional require-
ments may be necessary;
– in many countries, additional requirements are specified by the national health authorities, the national
authorities responsible for the protection of labour and similar authorities.
NOTE 103 This standard does not apply to
– motor-compressors designed exclusively for industrial purposes;
– motor-compressors used in appliances intended to be used in locations where special conditions prevail, such
as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
NOTE 104 If motor-compressors for refrigerant R-744 used in appliances with a transcritical refrigeration
system are equipped with pre
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.