SIST EN 61010-2-011:2017

Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-011: Particular requirements for refrigerating equipment (IEC 61010-2-011:2016)

This group safety publication is primarily intended to be used as a product safety standard for
the products mentioned in the scope, but shall also be used by technical committees in the
preparation of their publications for products similar to those mentioned in the scope of this
standard, in accordance with the principles laid down in IEC guide 104 and ISO/IEC Guide 51.
This Part 2 of IEC 61010 specifies particular safety requirements for the following types a) to
c) of electrical equipment and their accessories, wherever they are intended to be used,
whenever that equipment incorporates REFRIGERATING SYSTEMS whether an integral part of, or
remote to the equipment and the equipment is in direct control of the REFRIGERATING SYSTEM.
This Part 2 details all the requirements when up to 150 g of FLAMMABLE REFRIGERANT are used
per stage of a REFRIGERATING SYSTEM. Additional requirements beyond the current scope of
this standard apply if a refrigerant charge of FLAMMABLE REFRIGERANT exceeds this amount.

Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2-011: Besondere Anforderungen für KÜHLGERÄT (IEC 61010-2-011:2016)

Règles de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire - Partie 2-011: Exigences particulières pour appareils de réfrigération (IEC 61010-2-011:2016)

L'IEC 61010-2-011:2016 spécifie les exigences de sécurité particulières pour les types a) à c) suivants d'appareils électriques et leurs accessoires, quel que soit l'endroit dans lequel ils sont destinés à être utilisés, lorsque ces appareils comportent des SYSTEMES FRIGORIFIQUES, que ces derniers fassent partie intégrante des appareils ou qu'ils soient distants des appareils, et que les appareils sont sous la commande directe du SYSTEME FRIGORIFIQUE. La présente Partie 2 décrit toutes les exigences correspondant à l'utilisation d'une quantité de FLUIDE FRIGORIGENE INFLAMMABLE allant jusqu'à 150 g par étage d'un SYSTEME FRIGORIFIQUE. Lorsqu'une charge de FLUIDE FRIGORIGENE INFLAMMABLE dépasse cette quantité, des exigences supplémentaires hors du domaine d'application de la présente norme s'appliquent. Elle a le statut de publication groupée de sécurité, conformément au Guide 104 de l'IEC.
Cette publication doit être lue conjointement avec la IEC 61010-1:2010

Varnostne zahteve za električno opremo za meritve, nadzor in laboratorijsko uporabo - 2-011. del: Posebne zahteve za hladilno opremo (IEC 61010-2-011:2016)

Ta publikacija skupinske varnosti se uporablja predvsem kot standard o varnosti izdelka za izdelke, ki so omenjeni v okviru publikacije, vendar je namenjena tudi tehničnim odborom pri pripravi publikacij za izdelke, ki so podobni izdelkom, omenjenim v okviru tega standarda, skladno z načeli vodil IEC 104 in ISO/IEC 51.
Ta 2. del standarda IEC 61010 določa posebne varnostne zahteve za naslednje vrste a) do c) električne opreme in pribora, kadar sta namenjena uporabi, kadar oprema zajema HLADILNE SISTEME, ki so sestavni del ali oddaljeni od opreme, in oprema neposredno nadzoruje HLADILNI SISTEM. Ta 2. del podrobno opisuje vse zahteve, ko se v eni fazi HLADILNEGA SISTEMA uporablja do 150 g VNETLJIVEGA HLADILNEGA SREDSTVA. Dodatne zahteve, ki so zunaj področja uporabe tega standarda, se uporabljajo, če polnjenje VNETLJIVEGA HLADILNEGA SREDSTVA preseže to količino.

General Information

• Status: Withdrawn
• Publication Date: 07-Aug-2017
• Withdrawal Date: 05-Nov-2024
• ICS: 19.080 - Electrical and electronic testing
• ICS: 27.200 - Refrigerating technology
• ICS: 71.040.10 - Chemical laboratories. Laboratory equipment
• Technical Committee: MOV - Measuring equipment for electromagnetic quantities
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 05-Nov-2024
• Due Date: 28-Nov-2024
• Completion Date: 06-Nov-2024
• Ref Project: EN 61010-2-011:2017 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-011: Particular requirements for refrigerating equipment

Relations

• Replaced By: SIST EN IEC 61010-2-011:2022 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-011: Particular requirements for refrigerating equipment (IEC 61010-2-011:2019)
• Effective Date: 23-Nov-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2017
9DUQRVWQH]DKWHYH]DHOHNWULþQRRSUHPR]DPHULWYHQDG]RULQODERUDWRULMVNR
XSRUDERGHO3RVHEQH]DKWHYH]DKODGLOQRRSUHPR,(&
Safety requirements for electrical equipment for measurement, control, and laboratory
use - Part 2-011: Particular requirements for refrigerating equipment (IEC 61010-2-
011:2016)
Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 2
-011: Besondere Anforderungen für KÜHLGERÄT (IEC 61010-2-011:2016)
Règles de sécurité pour appareils électriques de mesurage, de régulation et de
laboratoire - Partie 2-011: Exigences particulières pour appareils de réfrigération (IEC
61010-2-011:2016)
Ta slovenski standard je istoveten z: EN 61010-2-011:2017
ICS:
19.080 (OHNWULþQRLQHOHNWURQVNR Electrical and electronic
SUHVNXãDQMH testing
27.200 Hladilna tehnologija Refrigerating technology
71.040.10 Kemijski laboratoriji. Chemical laboratories.
Laboratorijska oprema Laboratory equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 61010-2-011

NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2017
ICS 19.080
English Version
Safety requirements for electrical equipment for measurement,
control, and laboratory use - Part 2-011: Particular requirements
for refrigerating equipment
(IEC 61010-2-011:2016)
Règles de sécurité pour appareils électriques de mesurage, Sicherheitsbestimmungen für elektrische Mess-, Steuer-,
de régulation et de laboratoire - Partie 2-011: Exigences Regel- und Laborgeräte - Teil 2-011: Besondere
particulières pour appareils de réfrigération Anforderungen für KÜHLGERÄT
(IEC 61010-2-011:2016) (IEC 61010-2-011:2016)
This European Standard was approved by CENELEC on 2016-08-25. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61010-2-011:2017 E

European foreword
The text of document 66/589/FDIS, future edition 1 of IEC 61010-2-011, prepared by IEC/TC 66
"Safety of measuring, control and laboratory equipment" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN 61010-2-011:2017.
The following dates are fixed:
(dop) 2017-10-21
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2020-04-21
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 61010-2-011:2016 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
Addition
IEC 60079-20-1:2010 NOTE Harmonized as EN 60079-20-1:2010.
EN ISO 4126-1 NOTE Harmonized as EN ISO 4126-1.
EN ISO 4126-2 NOTE Harmonized as EN ISO 4126-2.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Addition
Publication Year Title EN/HD Year
IEC 60079-15 2010 Explosive atmospheres -- Part 15: EN 60079-15 2010
Equipment protection by type of protection
"n"
IEC 60335-2-34 2012 Household and similar electrical appliances EN 60335-2-34 2013
- Safety -- Part 2-34: Particular
requirements for motor-compressors
+ A1 2015  + A1 2015
UL 471 2010 Commercial refrigerators and freezers - -

IEC 61010-2-011 ®
Edition 1.0 2016-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
GROUP SAFETY PUBLICATION
PUBLICATION GROUPÉE DE SÉCURITÉ

Safety requirements for electrical equipment for measurement, control, and

laboratory use –
Part 2-011: Particular requirements for refrigerating equipment

Règles de sécurité pour appareils électriques de mesurage, de régulation et

de laboratoire –
Partie 2-011: Exigences particulières pour appareils de réfrigération

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 19.080 ISBN 978-2-8322-3505-8

– 2 – IEC 61010-2-011:2016 © IEC 2016
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope and object . 9
2 Normative references. 10
3 Terms and definitions . 10
4 Tests . 11
5 Marking and documentation . 13
6 Protection against electric shock . 17
7 Protection against mechanical HAZARDS . 17
8 Resistance to mechanical stresses . 17
9 Protection against the spread of fire . 17
10 Equipment temperature limits and resistance to heat . 18
11 Protection against HAZARDS from fluids . 19
12 Protection against radiation, including laser sources, and against sonic and
ultrasonic pressure . 29
13 Protection against liberated gases and substances, explosion and implosion . 29
14 Components and subassemblies . 30
15 Protection by safety interlocks . 30
16 HAZARDS resulting from application. 30
17 RISK assessment . 31
Annexes . 32
Annex G (informative) Leakage and rupture from fluids under pressure . 32
Annex L (informative) Index of defined terms . 32
Annex AA (normative) Non-sparking “n” electrical apparatus . 33
Annex BB (informative) HAZARDS associated with REFRIGERATING SYSTEMS and
refrigerants . 34
Annex CC (informative) Safety requirements for components and piping . 36
Annex DD (informative) Equipment containing FLAMMABLE REFRIGERANTS Information
and marking requirements . 41
Bibliography . 44

Figure 101 – Schema of a REFRIGERATING SYSTEM incorporating a condenser . 7
Figure 102 – Flow chart illustrating the selection process . 8
Figure 103 – Scratching TOOL tip details . 25

Table 1 – Symbols . 15
Table 101 – Maximum temperatures for motor-compressors . 18
Table 102 – Minimum temperature for determination of saturated vapor pressure of
refrigerant. 20
Table 103 – Refrigerant flammability parameters . 28
Table CC.1 – Parameters of pressure vessels according to EN 14276-1 . 36
Table CC.2 – Parameters of pipping according to EN 14276-2 . 38
Table CC.3 – Component and piping requirements . 39

IEC 61010-2-011:2016 © IEC 2016 – 3 –
Table CC.4 – Minimum wall thickness for copper and steel tubing . 40
Table DD.1 – Quantity of Group A2/A3 refrigerant per occupied space . 43

– 4 – IEC 61010-2-011:2016 © IEC 2016
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT
FOR MEASUREMENT, CONTROL, AND LABORATORY USE –

Part 2-011: Particular requirements for REFRIGERATING EQUIPMENT

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publication
...