SIST EN 60317-12:2010

Specifications for particular types of winding wires - Part 12: Polyvinyl acetal enamelled round copper wire, class 120 (IEC 60317-12:2010)

This Part of IEC 60317 specifies the requirements of enamelled round copper winding wire of class 120 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. Class 120 is a thermal class that requires a minimum temperature index of 120 and a heat shock temperature of at least 155 °C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor diameters covered by this standard is:
– Grade 1: 0,040 mm up to and including 2,500 mm;
– Grade 2: 0,040 mm up to and including 5,000 mm;
– Grade 3: 0,080 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 12: Runddrähte aus Kupfer, lackisoliert mit Polyvinylazetat, Klasse 120 (IEC 60317-12:2010)

Spécifications pour types particuliers de fils de bobinage - Partie 12: Fil de section circulaire en cuivre émaillé avec acétal de polyvinyle, classe 120 (CEI 60317-12:2010)

La CEI 60317-12:2010 concerne les fils de bobinage de section circulaire en cuivre émaillé de classe 120 avec un revêtement unique à base de résine acétal de polyvinyle qui peut être modifiée à condition qu'elle conserve l'identité chimique de la résine initiale et réponde à toutes les exigences du fil. Les modifications principales par rapport à l'édition précédente sont, de nouvelles exigences pour la détection des microfissures en immersion ont été ajoutées à l'Article 23.

Specifikacije za posebne vrste navitij - 12. del: S polivinil acetalom emajliran okrogel bakren vodnik, razred 120 (IEC 60317-12:2010)

Ta del IEC 60317 določa zahteve za emajliran okrogel bakren vodnik razreda 120 z enojnim premazom na osnovi polivinilacetalne smole, ki se lahko spremeni pod pogojem, da ohrani kemično identiteto originalne smole in izpolnjuje vse zahteve za vodnik. OPOMBA: Spremenjena smola je smola, ki je bila kemično spremenjena ali vsebuje enega ali več aditivov, ki izboljšujejo določene lastnosti delovanja ali uporabe. Razred 120 je toplotni razred, ki zahteva minimalni temperaturni indeks 120 in temperaturo toplotnega šoka vsaj 155 °C. Temperatura v stopinjah Celzija, ki ustreza temperaturnemu indeksu, ni nujno temperatura, priporočena za obratovanje vodnika, saj je to odvisno od številnih dejavnikov, vključno z vrsto vključene opreme. Razpon nominalnih premerov prevodnikov, ki jih zajema ta standard, je:
- Stopnja 1: 0,040 mm do vključno 2,500 mm;
- Stopnja 2: 0,040 mm do vključno 5,000 mm;
- Stopnja 3: 0,080 mm do vključno 5,000 mm;
Nominalne premere prevodnikov določa Klavzula 4 IEC 60317-0-1.

General Information

• Status: Withdrawn
• Publication Date: 21-Jul-2010
• Withdrawal Date: 15-Aug-2023
• ICS: 29.060.10 - Wires
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 27-Jul-2023
• Due Date: 19-Aug-2023
• Completion Date: 16-Aug-2023
• Ref Project: EN 60317-12:2010 - Specifications for particular types of winding wires - Part 12: Polyvinyl acetal enamelled round copper wire, class 120

Relations

• Replaced By: SIST EN IEC 60317-12:2020 - Specifications for particular types of winding wires - Part 12: Polyvinyl acetal enamelled round copper wire, class 120 (IEC 60317-12:2020)
• Effective Date: 03-Aug-2020
• Replaces: SIST EN 60317-12:2001/A2:2005 - Specifications for particular types of winding wires -- Part 12: Polyvinyl acetal enamelled round copper wire, class 120
• Effective Date: 28-Jan-2023
• Replaces: SIST EN 60317-12:2001/A1:2002 - Specifications for particular types of winding wires -- Part 12: Polyvinyl acetal enamelled round copper wire, class 120
• Effective Date: 29-Jan-2023
• Replaces: SIST EN 60317-12:2001 - Specifications for particular types of winding wires -- Part 12: Polyvinyl acetal enamelled round copper wire, class 120
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60317-12:2010
01-september-2010
1DGRPHãþD
SIST EN 60317-12:2001
SIST EN 60317-12:2001/A1:2002
SIST EN 60317-12:2001/A2:2005
Specifikacije za posebne vrste navitij - 12. del: S polivinil acetalom emajliran
okrogel bakren vodnik, razred 120 (IEC 60317-12:2010)
Specifications for particular types of winding wires - Part 12: Polyvinyl acetal enamelled
round copper wire, class 120 (IEC 60317-12:2010)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 12:
Runddrähte aus Kupfer, lackisoliert mit Polyvinylazetat, Klasse 120 (IEC 60317-12:2010)
Spécifications pour types particuliers de fils de bobinage - Partie 12: Fil de section
circulaire en cuivre émaillé avec acétal de polyvinyle, classe 120 (CEI 60317-12:2010)
Ta slovenski standard je istoveten z: EN 60317-12:2010
ICS:
29.060.10 Žice Wires
SIST EN 60317-12:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60317-12:2010

---------------------- Page: 2 ----------------------

SIST EN 60317-12:2010

EUROPEAN STANDARD
EN 60317-12

NORME EUROPÉENNE
April 2010
EUROPÄISCHE NORM

ICS 29.060.10 Supersedes EN 60317-12:1994 + A1:1998 + A2:2005


English version


Specifications for particular types of winding wires -
Part 12: Polyvinyl acetal enamelled round copper wire, class 120
(IEC 60317-12:2010)


Spécifications pour types particuliers  Technische Lieferbedingungen
de fils de bobinage - für bestimmte Typen von Wickeldrähten -
Partie 12: Fil de section circulaire Teil 12: Runddrähte aus Kupfer,
en cuivre émaillé avec acétal lackisoliert mit Polyvinylazetat, Klasse 120
de polyvinyle, classe 120 (IEC 60317-12:2010)
(CEI 60317-12:2010)




This European Standard was approved by CENELEC on 2010-04-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-12:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60317-12:2010
EN 60317-12:2010 - 2 -
Foreword
The text of document 55/1178/FDIS, future edition 3 of IEC 60317-12, prepared by IEC TC 55, Winding
wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60317-12 on 2010-04-01.
This European Standard supersedes EN 60317-12:1994 + A1:1998 + A2:2005.
The main changes with respect to the previous edition are listed below:
– new pin hole test requirements in Clause 23 have been added.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-01-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-04-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60317-12:2010 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60317-12:2010
- 3 - EN 60317-12:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60317-0-1 2008 Specifications for particular types of winding EN 60317-0-1 2008
wires -
Part 0-1: General requirements - Enamelled
round copper wire

---------------------- Page: 5 ----------------------

SIST EN 60317-12:2010

---------------------- Page: 6 ----------------------

SIST EN 60317-12:2010
IEC 60317-12
®
Edition 3.0 2010-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Specifications for particular types of winding wires –
Part 12: Polyvinyl acetal enamelled round copper wire, class 120

Spécifications pour types particuliers de fils de bobinage –
Partie 12: Fil de section circulaire en cuivre émaillé avec acétal de polyvinyle,
classe 120


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
J
CODE PRIX
ICS 29.060.10 ISBN 2-8318-1082-8
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60317-12:2010
– 2 – 60317-12 © IEC:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Terms, definitions and general notes on methods of test and appearance .6
3.1 Terms and definition.6
3.2 General notes on methods of test.6
3.3 Appearance.7
4 Dimensions .7
5 Electrical resistance .7
6 Elongation .7
7 Springiness .7
8 Flexibility and adherence.7
9 Heat shock .7
9.1 Nominal conductor diameters up to and including 1,600 mm .7
9.2 Nominal conductor diameters over 1,600 mm .7
10 Cut-through .8
11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and
including 2,500 mm) .8
12 Resistance to solvents.8
13 Breakdown voltage .8
14 Continuity of insulation .8
15 Temperature index .9
16 Resistance to refrigerants.9
17 Solderability .9
18 Heat or solvent bonding.9
19 Dielectric dissipation factor.9
20 Resistance to transformer oil .9
21 Loss of mass .9
23 Pin hole test .9
30 Packaging .9

Table 1 – Heat shock .7
Table 2 – Resistance to abrasion.8

---------------------- Page: 8 ----------------------

SIST EN 60317-12:2010
60317-12 © IEC:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –

Part 12: Polyvinyl acetal enamelled
round copper wire, class 120


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for stand
...