SIST EN IEC 61326-2-5:2021
(Main)Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditionsand performance criteria for field devices with field bus interfaces according to IEC 61784-1 (IEC 61326-2-5:2020)
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditionsand performance criteria for field devices with field bus interfaces according to IEC 61784-1 (IEC 61326-2-5:2020)
In addition to the requirements of IEC 61326-1, this part of IEC 61326 treats the particular
features for EMC testing of field devices with field bus interfaces. This part of IEC 61326 covers
only the field bus interface of the equipment.
NOTE The other functions of the equipment remain covered by other parts of IEC 61326 series.
This part refers only to field devices intended for use in process control and process measuring.
In this document, field devices with interfaces according to IEC 61784-1:2019, CP 3/2 and
CP 1/1 as defined in IEC 61784 are covered. Other field bus interfaces may be included in
future editions of this document.
IEC 61784-1:2019 specifies a set of protocol specific communication profiles based on
IEC 61158.
The manufacturer specifies the environment for which the product is intended to be used and/or
selects the appropriate test level specifications of IEC 61326-1.
Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-Anforderungen - Teil 2-5: Besondere Anforderungen - Prüfanordnungen, Betriebsbedingungen und Leistungsmerkmale für Feldgeräte mit Feldbus-Schnittstellen nach IEC 61784-1 (IEC 61326-2-5:2020)
Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la CEM - Partie 2-5: Exigences particulières - Configurations d'essai, conditions de fonctionnement et critères d'aptitude à la fonction pour les équipements de terrain avec les interfaces utilisant des bus de terrain conformes à la CEI 61784-1 (IEC 61326-2-5:2020)
IEC 61326-2-5:2020 est disponible sous forme de IEC 61326-2-5:2020 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L'IEC 61326-1:2020 traite des caractéristiques particulières pour les essais de CEM des équipements de terrain avec des interfaces utilisant des bus de terrain. La présente partie de l’IEC 61326 couvre uniquement l'interface utilisant le bus de terrain du matériel.La présente partie fait uniquement référence aux équipements de terrain destinés à être utilisés pour les commandes et les mesurages des processus. Le présent document traite des équipements de terrain utilisant des interfaces conformes à l’IEC 61784-1:2019, CP 3/2 et CP 1/1 telles qu'elles sont définies dans l’IEC 61784. D'autres interfaces de bus de terrain peuvent être incluses dans les futures éditions du présent document.
Električna oprema za merjenje, nadzor in laboratorijsko uporabo - Zahteve za elektromagnetno združljivost (EMC) - 2-5. del: Posebne zahteve - Preskusne konfiguracije, obratovalni pogoji in merila učinkovitosti za delovanje operativnih naprav s procesnim vodilom v skladu z IEC 61784-1 (IEC 61326-2-5:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 61326-2-5:2021
01-september-2021
Nadomešča:
SIST EN 61326-2-5:2013
Električna oprema za merjenje, nadzor in laboratorijsko uporabo - Zahteve za
elektromagnetno združljivost (EMC) - 2-5. del: Posebne zahteve - Preskusne
konfiguracije, obratovalni pogoji in merila učinkovitosti za delovanje operativnih
naprav s procesnim vodilom v skladu z IEC 61784-1 (IEC 61326-2-5:2020)
Electrical equipment for measurement, control and laboratory use - EMC requirements -
Part 2-5: Particular requirements - Test configurations, operational conditionsand
performance criteria for field devices with field bus interfaces according to IEC 61784-1
(IEC 61326-2-5:2020)
Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-Anforderungen - Teil 2-5:
Besondere Anforderungen - Prüfanordnungen, Betriebsbedingungen und
Leistungsmerkmale für Feldgeräte mit Feldbus-Schnittstellen nach IEC 61784-1 (IEC
61326-2-5:2020)
Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la
CEM - Partie 2-5: Exigences particulières - Configurations d'essai, conditions de
fonctionnement et critères d'aptitude à la fonction pour les équipements de terrain avec
les interfaces utilisant des bus de terrain conformes à la CEI 61784-1 (IEC 61326-2-
5:2020)
Ta slovenski standard je istoveten z: EN IEC 61326-2-5:2021
ICS:
19.080 Električno in elektronsko Electrical and electronic
preskušanje testing
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN IEC 61326-2-5:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 61326-2-5:2021
---------------------- Page: 2 ----------------------
SIST EN IEC 61326-2-5:2021
EUROPEAN STANDARD EN IEC 61326-2-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2021
ICS 25.040.40; 17.220.20; 33.100.20 Supersedes EN 61326-2-5:2013 and all of its
amendments and corrigenda (if any)
English Version
Electrical equipment for measurement, control and laboratory
use - EMC requirements - Part 2-5: Particular requirements -
Test configurations, operational conditions and performance
criteria for field devices with field bus interfaces according to IEC
61784-1
(IEC 61326-2-5:2020)
Matériel électrique de mesure, de commande et de Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-
laboratoire - Exigences relatives à la CEM - Partie 2-5: Anforderungen - Teil 2-5: Besondere Anforderungen -
Exigences particulières - Configurations d'essai, conditions Prüfanordnungen, Betriebsbedingungen und
de fonctionnement et critères de performance pour les Leistungsmerkmale für Feldgeräte mit Feldbus-
équipements de terrain avec des interfaces utilisant des bus Schnittstellen nach IEC 61784-1
de terrain conformes à l'IEC 61784-1 (IEC 61326-2-5:2020)
(IEC 61326-2-5:2020)
This European Standard was approved by CENELEC on 2020-12-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61326-2-5:2021 E
---------------------- Page: 3 ----------------------
SIST EN IEC 61326-2-5:2021
EN IEC 61326-2-5:2021 (E)
European foreword
The text of document 65A/978/FDIS, future edition 3 of IEC 61326-2-5, prepared by SC 65A "System
aspects" of IEC/TC 65 "Industrial-process measurement, control and automation" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61326-2-5:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-12-04
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-06-04
document have to be withdrawn
This document supersedes EN 61326-2-5:2013 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 61326-2-5:2020 was approved by CENELEC as a
European Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 61326-2-5:2021
EN IEC 61326-2-5:2021 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
The Annex ZA of EN IEC 61326-1:2021 applies with the following additions:
Publication Year Title EN/HD Year
IEC 61158-2 2014 Industrial communication networks - EN 61158-2 2014
Fieldbus specifications - Part 2: Physical
layer specification and service definition
IEC 61158-3-3 2014 Industrial communication networks - EN 61158-3-3 2014
Fieldbus specifications - Part 3-3: Data-link
layer service definition - Type 3 elements
IEC 61158-5-5 2014 Industrial communication networks - EN 61158-5-5 2014
Fieldbus specifications - Part 5-5:
Application layer service definition - Type 5
elements
IEC 61158-6-10 2019 Industrial communication networks - EN IEC 61158-6-10 2019
Fieldbus specifications - Part 6-10:
Application layer protocol specification -
Type 10 elements
IEC 61326-1 2020 Electrical equipment for measurement, EN IEC 61326-1 2021
control and laboratory use - EMC
requirements - Part 1: General
requirements
IEC 61784-1 2019 Industrial communication networks - EN IEC 61784-1 2019
Profiles Part 1: Fieldbus profiles
3
---------------------- Page: 5 ----------------------
SIST EN IEC 61326-2-5:2021
---------------------- Page: 6 ----------------------
SIST EN IEC 61326-2-5:2021
IEC 61326-2-5
®
Edition 3.0 2020-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electrical equipment for measurement, control and laboratory use –
EMC requirements –
Part 2-5: Particular requirements – Test configurations, operational conditions
and performance criteria for field devices with field bus interfaces according to
IEC 61784-1
Matériel électrique de mesure, de commande et de laboratoire –
Exigences relatives à la CEM –
Partie 2-5: Exigences particulières – Configurations d'essai, conditions de
fonctionnement et critères de performance pour les équipements de terrain
avec des interfaces utilisant des bus de terrain conformes à l’IEC 61784-1
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.20; 25.040.40; 33.100.20 ISBN 978-2-8322-8952-5
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 61326-2-5:2021
– 2 – IEC 61326-2-5:2020 © IEC 2020
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 General . 6
5 EMC test plan . 6
5.1 General . 6
5.2 Configuration of EUT during testing . 6
5.3 Operation conditions of EUT during testing . 6
5.4 Specification of FUNCTIONAL PERFORMANCE . 6
5.5 Test description . 6
6 Immunity requirements . 6
6.1 Conditions during the tests. 6
6.2 Immunity test requirements . 7
6.3 Random aspects . 7
6.4 Performance criteria . 7
7 Emission requirements . 7
8 Test results and test report . 7
9 Instructions for use . 7
Annex A (normative) Immunity test requirements for PORTABLE TEST AND MEASUREMENT
EQUIPMENT powered by battery or from the circuit being measured . 8
Annex B (informative) Guide for analysis and assessment for electromagnetic
compatibility. 9
Annex AA (normative) Particular requirements – Test configurations, operational
conditions and performance criteria for field devices with field bus interfaces according
to IEC 61784-1 CP 1/1 . 10
AA.1 General . 10
AA.2 EMC test plan . 10
AA.2.1 Configuration of EUT with CP 1/1 interface during testing . 10
AA.2.2 Operation conditions of EUT with CP 1/1 interface during testing . 12
AA.3 Performance criteria . 14
AA.4 Information on the host system . 14
Annex BB (normative) Particular requirements – Test configurations, operational
conditions and performance criteria for field devices with field bus interfaces according
to IEC 61784-1 CP 3/2 . 15
BB.1 General . 15
BB.2 EMC test plan . 15
BB.2.1 Configuration of EUT with CP 3/2 interface during testing . 15
BB.2.2 Operation conditions of EUT with CP 3/2 interface during testing . 17
BB.3 Performance criteria . 18
Figure AA.1 – Test set up for EUT with CP 1/1 interface . 12
Figure BB.1 – Test set up for EUT with CP 3/2 interface . 17
---------------------- Page: 8 ----------------------
SIST EN IEC 61326-2-5:2021
IEC 61326-2-5:2020 © IEC 2020 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL EQUIPMENT FOR MEASUREMENT,
CONTROL AND LABORATORY USE –
EMC REQUIREMENTS –
Part 2-5: Particular requirements –
Test configurations, operational conditions and performance criteria
for field devices with field bus interfaces according to IEC 61784-1
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61326-2-5 has been prepared by subcommittee 65A: System
aspects, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This third edition cancels and replaces the second edition published in 2012. This edition
constitutes a technical revision.
This edition includes the following significant technical change with respect to the previous
edition:
– update with respect to IEC 61326-1:2020.
---------------------- Page: 9 ----------------------
SIST EN IEC 61326-2-5:2021
– 4 – IEC 61326-2-5:2020 © IEC 2020
The text of this International Standard is based on the following documents:
FDIS Report on voting
65A/978/FDIS 65A/989/RVD
Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
This part of IEC 61326 series is to be used in conjunction with IEC 61326-1:2020 and follows
the same numbering of clauses, subclauses, tables and figures.
When a particular subclause of IEC 61326-1 is not mentioned in this part, that subclause applies
as far as is reasonable. When this standard states “addition”, “modification” or “replacement”,
the relevant text in IEC 61326-1 is to be adapted accordingly.
NOTE The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in IEC 61326-1;
– unless notes are in a new subclause or involve notes in IEC 61326-1, they are numbered starting from 101
including those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.
A list of all parts of IEC 61326 series, under the general title Electrical equipment for
measurement, control and laboratory use – EMC requirements can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 10 ----------------------
SIST EN IEC 61326-2-5:2021
IEC 61326-2-5:2020 © IEC 2020 – 5 –
ELECTRICAL EQUIPMENT FOR MEASUREMENT,
CONTROL AND LABORATORY USE –
EMC REQUIREMENTS –
Part 2-5: Particular requirements –
Test configurations, operational conditions and performance criteria
for field devices with field bus interfaces according to IEC 61784-1
1 Scope
In addition to the requirements of IEC 61326-1, this part of IEC 61326 treats the particular
features for EMC testing of field devices with field bus interfaces. This part of IEC 61326 covers
only the field bus interface of the equipment.
NOTE The other functions of the equipment remain covered by other parts of IEC 61326 series.
This part refers only to field devices intended for use in process control and process measuring.
In this document, field devices with interfaces according to IEC 61784-1:2019, CP 3/2 and
CP 1/1 as defined in IEC 61784 are covered. Other field bus interfaces may be included in
future editions of this document.
IEC 61784-1:2019 specifies a set of protocol specific communication profiles based on
IEC 61158.
The manufacturer specifies the environment for which the product is intended to be used and/or
selects the appropriate test level specifications of IEC 61326-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
Clause 2 of IEC 61326-1:2020 applies except as follows:
Addition:
IEC 61158-2:2014, Industrial communication networks – Fieldbus specifications – Part 2:
Physical layer specification and service definition
IEC 61158-3-3:2014, Industrial communication networks – Fieldbus specifications – Part 3-3:
Data-link layer service definition – Type 3 elements
IEC 61158-5-5:2014, Industrial communication networks – Fieldbus specificat
...
SLOVENSKI STANDARD
oSIST prEN IEC 61326-2-5:2019
01-oktober-2019
Električna oprema za merjenje, kontrolo in laboratorijsko uporabo - Zahteve za
elektromagnetno združljivost (EMC) - 2-5. del: Posebne zahteve - Preskusne
konfiguracije, obratovalni pogoji in merila za delovanje terenskih naprav z
vmesnikom po IEC 61784-1
Electrical equipment for measurement, control and laboratory use - EMC requirements -
Part 2-5: Particular requirements - Test configurations, operational conditions and
performance criteria for field devices with field bus interfaces according to IEC 61784-1
Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la
CEM - Partie 2-5: Exigences particulières - Configurations d'essai, conditions de
fonctionnement et critères d'aptitude à la fonction pour les équipements de terrain avec
les interfaces utilisant des bus de terrain conformes à la CEI 61784-1
Ta slovenski standard je istoveten z: prEN IEC 61326-2-5:2019
ICS:
19.080 Električno in elektronsko Electrical and electronic
preskušanje testing
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
oSIST prEN IEC 61326-2-5:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN IEC 61326-2-5:2019
---------------------- Page: 2 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61326-2-5 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2019-08-23 2019-11-15
SUPERSEDES DOCUMENTS:
65A/908/CD, 65A/918A/CC
IEC SC 65A: SYSTEM ASPECTS
SECRETARIAT: SECRETARY:
United Kingdom Mr Petar Luzajic
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
TC 77, SC 77A
Other TC/SCs are requested to indicate their interest, if any, in
this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for Vote
(CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
TITLE:
Electrical equipment for measurement, control and laboratory use – EMC requirements – Part 2-5: Particular
requirements – Test configurations, operational conditions and performance criteria for field devices with field
bus interfaces according to IEC 61784-1
PROPOSED STABILITY DATE: 2023
NOTE FROM TC/SC OFFICERS:
Copyright © 2019 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV – 2 – IEC CDV 61326-2-5 © IEC 2019
1 CONTENTS
2 FOREWORD . 3
3 1 Scope . 5
4 2 Normative references . 5
5 3 Terms and definitions . 6
6 4 General . 6
7 5 EMC test plan . 6
8 5.1 General . 6
9 5.2 Configuration of EUT during testing . 6
10 5.3 Operation conditions of EUT during testing . 6
11 5.4 Specification of functional performance . 6
12 5.5 Test description . 6
13 6 Immunity requirements . 6
14 6.1 Conditions during the tests . 6
15 6.2 Immunity test requirements . 6
16 6.3 Random aspects. 6
17 6.4 Performance criteria . 7
18 7 Emission requirements . 7
19 8 Test results and test report . 7
20 9 Instructions for use . 7
21 Annex AA (normative) Particular requirements – Test configurations, operational
22 conditions and performance criteria for field devices with field bus interfaces according
23 to IEC 61784-1 CP 1/1 . 8
24 Annex BB (normative) Particular requirements – Test configurations, operational
25 conditions and performance criteria for field devices with field bus interfaces according
26 to IEC 61784-1 CP 3/2 . 13
27
28 Figure AA.1 – Test set up for EUT with CP 1/1 interface . 10
29 Figure BB.1 – Test set up for EUT with CP 3/2 interface . 15
30
---------------------- Page: 4 ----------------------
oSIST prEN IEC 61326-2-5:2019
IEC CDV 61326-2-5 © IEC 2019 – 3 – 65A/927/CDV
31 INTERNATIONAL ELECTROTECHNICAL COMMISSION
32 ____________
33
34 ELECTRICAL EQUIPMENT FOR MEASUREMENT,
35 CONTROL AND LABORATORY USE –
36 EMC REQUIREMENTS –
37
38 Part 2-5: Particular requirements –
39 Test configurations, operational conditions and performance criteria
40 for field devices with field bus interfaces according to IEC 61784-1
41
42
43 FOREWORD
44 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
45 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
46 international co-operation on all questions concerning standardization in the electrical and electronic fields. To
47 this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
48 Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
49 Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
50 in the subject dealt with may participate in this preparatory work. International, governmental and non-
51 governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
52 with the International Organization for Standardization (ISO) in accordance with conditions determined by
53 agreement between the two organizations.
54 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
55 consensus of opinion on the relevant subjects since each technical committee has representation from all
56 interested IEC National Committees.
57 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
58 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
59 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
60 misinterpretation by any end user.
61 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
62 transparently to the maximum extent possible in their national and regional publications. Any divergence
63 between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
64 the latter.
65 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
66 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
67 services carried out by independent certification bodies.
68 6) All users should ensure that they have the latest edition of this publication.
69 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
70 members of its technical committees and IEC National Committees for any personal injury, property damage or
71 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
72 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
73 Publications.
74 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
75 indispensable for the correct application of this publication.
76 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
77 patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
78 International Standard IEC 61326-2-5 has been prepared by subcommittee 65A: System
79 aspects, of IEC technical committee 65: Industrial-process measurement, control and
80 automation.
81 This third edition cancels and replaces the second edition published in 2012. This edition
82 constitutes a technical revision.
83
---------------------- Page: 5 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV – 4 – IEC CDV 61326-2-5 © IEC 2019
84 The main technical changes with regard to the previous edition are as follows:
85 – Update with respect to IEC 61326-1:20xx.
86 The text of this standard is based on the following documents:
FDIS Report on voting
65A/xxx/FDIS 65A/xxx/RVD
87
88 Full information on the voting for the approval of this standard can be found in the report on
89 voting indicated in the above table.
90 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
91 This part of IEC 61326 series is to be used in conjunction with IEC 61326-1:20xx and follows
92 the same numbering of clauses, subclauses, tables and figures.
93 When a particular subclause of IEC 61326-1 is not mentioned in this part, that subclause
94 applies as far as is reasonable. When this standard states “addition”, “modification” or
95 “replacement”, the relevant text in IEC 61326-1 is to be adapted accordingly.
96 NOTE The following numbering system is used:
97 – subclauses, tables and figures that are numbered starting from 101 are additional to those in
98 IEC 61326-1;
99 – unless notes are in a new subclause or involve notes in IEC 61326-1, they are numbered starting from 101
100 including those in a replaced clause or subclause;
101 – additional annexes are lettered AA, BB, etc.
102 A list of all parts of IEC 61326 series, under the general title Electrical equipment for
103 measurement, control and laboratory use – EMC requirements can be found on the IEC
104 website.
105 The committee has decided that the contents of this publication will remain unchanged until
106 the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
107 related to the specific publication. At this date, the publication will be
108 • reconfirmed,
109 • withdrawn,
110 • replaced by a revised edition, or
111 • amended.
112
113
114
---------------------- Page: 6 ----------------------
oSIST prEN IEC 61326-2-5:2019
IEC CDV 61326-2-5 © IEC 2019 – 5 – 65A/927/CDV
115 ELECTRICAL EQUIPMENT FOR MEASUREMENT,
116 CONTROL AND LABORATORY USE –
117 EMC REQUIREMENTS –
118
119 Part 2-5: Particular requirements –
120 Test configurations, operational conditions and performance criteria
121 for field devices with field bus interfaces according to IEC 61784-1
122
123
124
125 1 Scope
126 In addition to the requirements of International Standard IEC 61326-1:20xx, this part of IEC
127 61326 series treats the particular features for EMC testing of field devices with field bus
128 interfaces. This part of IEC 61326 covers only the field bus interface of the equipment.
129 NOTE The other functions of the equipment remain covered by other parts of IEC 61326 series.
130 This part refers only to field devices intended for use in process control and process
131 measuring.
132 In this standard field devices with interfaces according to IEC 61784-1:2014, CP 3/2 and CP
133 1/1 as defined in IEC 61784 are covered. Other field busses may be included in future editions
134 of this standard.
135 The IEC 61784-1:2014 specifies a set of protocol specific communication profiles based on
136 IEC 61158.
137 The manufacturer specifies the environment for which the product is intended to be used
138 and/or selects the appropriate test level specifications of IEC 61326-1.
139 2 Normative references
140 The following documents, in whole or in part, are normatively referenced in this document and
141 are indispensable for its application. For dated references, only the edition cited applies. For
142 undated references, the latest edition of the referenced document (including any
143 amendments) applies.
144 Clause 2 of IEC 61326-1:20xx applies except as follows:
145 Addition:
146 IEC 61158-2:2014, Industrial communication networks – Fieldbus specifications – Part 2:
147 Physical layer specification and service definition
148 IEC 61158-3-3:2014, Industrial communication networks – Fieldbus specifications – Part 3-3:
149 Data-link layer service definition – Type 3 elements
150 IEC 61158-5-5:2014, Industrial communication networks – Fieldbus specifications – Part 5-5:
151 Application layer service definition – Type 5 elements
152 IEC 61158-6-10:2014, Industrial communication networks – Fieldbus specifications – Part 6-
153 10: Application layer protocol specification – Type 10 elements
---------------------- Page: 7 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV – 6 – IEC CDV 61326-2-5 © IEC 2019
154 IEC 61784-1:2014, Industrial communication networks – Profiles – Part 1: Fieldbus profiles
155 3 Terms and definitions
156 Clause 3 of IEC 61326-1:20xx applies.
157 4 General
158 Clause 4 of IEC 61326-1:20xx applies.
159 5 EMC test plan
160 5.1 General
161 Subclause 5.1 of IEC 61326-1:20xx applies.
162 5.2 Configuration of EUT during testing
163 Subclause 5.2 of IEC 61326-1:20xx applies, except as follows:
164 Addition:
165 Additional requirements: see Annexes AA and BB.
166 5.3 Operation conditions of EUT during testing
167 Subclause 5.3 of IEC 61326-1:20xx applies, except as follows:
168 Addition:
169 Additional requirements: see Annexes AA and BB.
170 5.4 Specification of functional performance
171 Subclause 5.4 of IEC 61326-1:20xx applies.
172 5.5 Test description
173 Subclause 5.5 of IEC 61326-1:20xx applies.
174 6 Immunity requirements
175 6.1 Conditions during the tests
176 Subclause 6.1 of IEC 61326-1:20xx applies.
177 6.2 Immunity test requirements
178 Subclause 6.2 of IEC 61326-1:20xx applies.
179 6.3 Random aspects
180 Subclause 6.3 of IEC 61326-1:20xx applies.
---------------------- Page: 8 ----------------------
oSIST prEN IEC 61326-2-5:2019
IEC CDV 61326-2-5 © IEC 2019 – 7 – 65A/927/CDV
181 6.4 Performance criteria
182 Subclause 6.4 of IEC 61326-1:20xx applies, except as follows:
183 Addition:
184 Additional requirements: see Annexes AA and BB.
185 7 Emission requirements
186 Clause 7 of IEC 61326-1:20xx applies.
187 8 Test results and test report
188 Clause 8 of IEC 61326-1:20xx applies, except as follows:
189 Addition:
190 The type of shield connection at the EUT shall be stated in the test report.
191 9 Instructions for use
192 Clause 9 of IEC 61326-1:20xx applies.
193
---------------------- Page: 9 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV – 8 – IEC CDV 61326-2-5 © IEC 2019
194 Annex AA
195 (normative)
196
197 Particular requirements –
198 Test configurations, operational conditions and performance criteria for
199 field devices with field bus interfaces according to IEC 61784-1 CP 1/1
200
201 AA.1 General
202 In connection with the main part of this standard, this Annex AA describes specific test
203 configurations, operational conditions and performance criteria regarding the field bus
204 interface using the communication profile CP 1/1 according to IEC 61784-1:2014.
205 To prevent confusion with requirements of other annexes, the equipment under test (EUT) is
206 called “EUT with CP 1/1 interface” throughout this annex.
207 AA.2 EMC test plan
208 AA.2.1 Configuration of EUT with CP 1/1 interface during testing
209 Subclause 5.2 of IEC 61326-1:20xx applies, except as follows:
210 Addition:
211 AA.2.1.1 Test configuration for EUT with CP 1/1 interface
212 In order to assign any malfunction of the communication during the EMC-test to the EUT with
213 CP 1/1 interface, the configuration of field devices with interfaces according to IEC 61784-
214 1:2014, CP 1/1 shall be limited to the operation of one host system and one EUT with CP 1/1
215 interface during EMC type tests.
216 Ports other than I/O ports covered by this part of the standard are tested according to
217 IEC 61326-1:20xx.
218 The connection plan is shown in Figure AA.1.
219 The field device is connected via a device coupler with the power conditioner and the host
220 system.
221 A standardised field bus terminator is attached
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.