SIST EN 26:2015/oprA1:2016
(Amendment)Gas-fired instantaneous water heaters for the production of domestic hot water
Gas-fired instantaneous water heaters for the production of domestic hot water
This European Standard defines the specifications and test methods concerning the construction, safety, rational use of energy and fitness for purpose, and also the classification and marking of gas-fired instantaneous water heaters for sanitary uses, hereafter called “water heaters”.
This European Standard applies to water heaters:
- of types AAS, B11, B11BS, B12, B12BS, B13, B13BS, B14, B22, B23, B32, B33, B44, B52, B53, C11, C12, C13, C21, C22, C23, C32, C33, C42, C43, C52, C53, C62, C63, C72, C73, C82and C83 according to CEN/TR 1749;
- fitted with atmospheric burners;
- equipped with atmospheric burners assisted by a fan for the supply of combustion air or evacuation of combustion products or fully premix burners;
- using one or more combustible gases corresponding to the three gas families and at the pressures stated in accordance to EN 437;
- of nominal heat input not exceeding 70 kW;
- with an ignition burner or with direct ignition of the main burner.
In this European Standard, the heat inputs are expressed in relation to the net calorific value (Hi).
This European Standard does not contain all the requirements necessary for:
- boiling water appliances;
- appliances intended to be connected to a mechanical means of evacuating the combustion products;
- appliances which fulfil a dual role of space heating and heating water for sanitary use;
- appliances making use of the heat of condensation of the water contained in the combustion products;
- water heaters of types B21, B31, B41, B42, B43 and B51.
This European Standard only covers water heaters where the fan, if any, is an integral part of the appliance.
This European Standard:
- does not apply to appliances not intended to be connected to a flue when they are not fitted with an atmosphere sensing device;
- takes account of the information given in Technical Report CEN/CR 1472:1994 with respect to marking.
Type B appliances should be with a combustion products discharge safety device to comply with essential requirement 3.4.3 of the Gas Appliances Directive 2009/142/EC. In this European Standard, the appliance is identified as type B11BS.
Appliances intended to be installed outdoors or in a room separate from inhabited rooms and provided with appropriate ventilation are not required to have this combustion products discharge safety device but, in this case, appropriate warnings on the packaging, and in the instructions should clearly define the limited authorized use for this type of appliance. In this European Standard, the appliance is identified as type B11.
The main symbols used in this European Standard are summarized in Annex F.
Gasbeheizte Durchlauf-Wasserheizer für den sanitären Gebrauch
Apapreils de production instantanée d'eau chaude pour usages sanitaires utilisant les combustibles gazeux
Le premier alinéa est remplacé par le texte suivant :
« La présente Norme européenne définit les spécifications et les méthodes d’essai relatives à la construction, la sécurité, l’utilisation rationnelle de l’énergie et l’aptitude à la fonction ainsi que la catégorie, le marquage et l’étiquetage énergétique des appareils de production instantanée d’eau chaude pour usages sanitaires utilisant les combustibles gazeux, désignés ci-après « chauffe-eau ». »
Dans le deuxième alinéa, premier tiret, la mention « selon le CEN/TR 1749 » est supprimée.
La note suivante est ajoutée :
« NOTE Pour de plus amples informations concernant la configuration des types d’appareils, voir le CEN/TR 1749:2014 [5]. »
Dans le deuxième alinéa, le troisième tiret ci-dessous est supprimé :
« — équipés de brûleurs atmosphériques assistés d’un ventilateur pour l’arrivée d’air de combustion ou l’évacuation des produits de combustion ou de brûleurs à prémélange total ; »
Dans le deuxième alinéa, le cinquième tiret est complété de la manière suivante :
« — de débit calorifique nominal inférieur ou égal à 70 kW basé sur le pouvoir calorifique inférieur (Hi) ; »
Dans le quatrième alinéa, le cinquième tiret ci-dessous est supprimé :
« — les appareils des types B21, B31, B41, B42, B43 et B51. »
Le sixième alinéa ci-dessous est supprimé :
« La présente Norme européenne :
ne s’applique pas aux appareils non destinés à être connectés à une cheminée lorsqu’ils ne sont pas équipés d’un dispositif de contrôle de viciation de l’atmosphère ;
tient compte des informations fournies dans le rapport technique CR 1472:1994 relatif au marquage. »
Pretočni plinski grelniki za pripravo sanitarne tople vode - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 26:2015/oprA1:2016
01-julij-2016
3UHWRþQLSOLQVNLJUHOQLNL]DSULSUDYRVDQLWDUQHWRSOHYRGH'RSROQLOR$
Gas-fired instantaneous water heaters for the production of domestic hot water
Gasbeheizte Durchlauf-Wasserheizer für den sanitären Gebrauch
Apapreils de production instantanée d'eau chaude pour usages sanitaires utilisant les
combustibles gazeux
Ta slovenski standard je istoveten z: EN 26:2015/prA1:2016
ICS:
91.140.65 Oprema za ogrevanje vode Water heating equipment
97.100.20 Plinski grelniki Gas heaters
SIST EN 26:2015/oprA1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 26:2015/oprA1:2016
---------------------- Page: 2 ----------------------
SIST EN 26:2015/oprA1:2016
EUROPEAN STANDARD
DRAFT
EN 26:2015
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
May 2016
ICS 91.140.10
English Version
Gas-fired instantaneous water heaters for the production of
domestic hot water
Apapreils de production instantanée d'eau chaude pour Gasbeheizte Durchlauf-Wasserheizer für den sanitären
usages sanitaires utilisant les combustibles gazeux Gebrauch
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 48.
This draft amendment A1, if approved, will modify the European Standard EN 26:2015. If this draft becomes an amendment, CEN members
are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment into the
relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 26:2015/prA1:2016:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 26:2015/oprA1:2016
EN 26:2015/prA1:2016 (E)
Contents Page
European foreword . 3
1 Modifications to the Foreword . 4
2 Modifications to Clause 1, Scope . 4
3 Modifications to Clause 2, Normative references . 5
4 Modifications to Clause 3, Terms and definitions . 7
5 Modifications to Clause 4, Classification of water heaters . 7
6 Modifications to Clause 5, Constructional requirements . 7
7 Modifications to Clause 6, Operational requirements . 8
8 Modifications to Clause 7, Rational use of energy . 10
8 Modifications to Figure 2 . 11
9 Modifications to Clause 9, Marking and instructions . 11
10 Modifications to Clause 10, Ecodesign Data . 12
11 Modification to Annex B . 12
12 Modifications to Annex ZA . 12
13 Modifications to Bibliography . 13
2
---------------------- Page: 4 ----------------------
SIST EN 26:2015/oprA1:2016
EN 26:2015/prA1:2016 (E)
European foreword
This document (EN 26:2015/prA1:2016) has been prepared by Technical Committee CEN/TC 48 “”, the
secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
3
---------------------- Page: 5 ----------------------
SIST EN 26:2015/oprA1:2016
EN 26:2015/prA1:2016 (E)
1 Modifications to the Foreword
th th th
5 , 6 and 7 paragraphs are replaced by the following text:
"This European Standard has been prepared under mandate M89/6 given to CEN by the European
Commission and the European Free Trade Association to provide a means of conforming to Essential
Requirements of EU Directive 2009/142/EC, relating to appliances burning gaseous fuels.
This amendment (A1) has been prepared under mandate M/534, given to CEN by the European
Commission
and the European Free Trade Association to provide a means of conforming to:
- requirements of Commission Delegated Regulation (EU) No 812/2013 of 18 February 2013
implementing Directive 2010/30/UE of the European Parliament and of the Council with regard to
energy labelling requirements of water heaters, hot water tanks and packages of water heaters and
solar service;
- requirements of Commission Regulation (EU) No 814/2013 of 2 August 2013 implementing Directive
2009/125/EC of the European Parliament and of the Council with regard to eco design requirements
for water heaters and water storage tanks."
th
The 9 paragraph hereafter is deleted:
"It gives specific requirements or disposals relative to:
— requirements and test methods for type C water heaters with a fan incorporated in the combustion
air supply circuit or in the combustion products evacuation circuit;
— combustion products evacuation ducts which are part of a water heater;
— condensing water heaters;
— water heaters installed indoors and/or partially protected place;
— requirements and test procedures for resistance to freezing;
— NOx measurement;
— the metallic, plastic and other non-metallic materials that are used in water heaters and which
come into contact with water intended for human consumption. It is intended to ensure that products of
this kind complying with these requirements meet current technological development and
requirements with regard to the service life of the water heaters and their physiological suitability."
2 Modifications to Clause 1, Scope
st
The 1 paragraph is replaced by the following:
"This European Standard defines the specifications and test methods concerning the construction,
safety, rational use of energy and fitness for purpose, and also the classification, marking and energy
labelling of gas-fired instantaneous water heaters for sanitary uses, hereafter called “water heaters”.
nd
At the 2 paragraph, first indent, the term "according to CEN/TR 1749" is deleted.
4
---------------------- Page: 6 ----------------------
SIST EN 26:2015/oprA1:2016
EN 26:2015/prA1:2016 (E)
The following note is added:
"NOTE For more information on the configuration of the types of appliances, see CEN/TR 1749:2014 [5]"
nd th
At the 2 paragraph, the 3 indent hereafter is deleted:
"— equipped with atmospheric burners assisted by a fan for the supply of combustion air or evacuation
of combustion products or fully premix burners;"
nd th
At the 2 paragraph, the 5 indent is completed as follows:
"— of nominal heat input not exceeding 70 kW based on net calorific value (NCV);"
nd th
At the 4 paragraph, the 5 indent hereafter is deleted:
"— water heaters of types B , B , B , B , B and B ."
21 31 41 42 43 51
th
The 6 paragraph hereafter is deleted:
"This European Standard:
— does not apply to appliances not intended to be connected to a flue when they are not fitted with an
atmosphere sensing device;
— takes account of the information given in Technical Report CR 1472:1994 with respect to marking."
3 Modifications to Clause 2, Normative references
The following reference is deleted and moved to Bibliography:
"CEN/TR 1749, European scheme for the classification of gas appliances according to the method of
evacuation of the combustion products (types)"
The undated references are replaced by the following:
"EN 125:1991, Flame supervision devices for gas burning appliances — Thermoelectric flame supervision
devices
EN 126:2012, Multifunctional controls for gas burning appliances
EN 161:2011, Automatic shut-off valves for gas burners and gas appliances
EN 437+A1:2009, Test gases, test pressures, appliance categories
EN 513:2000, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors —
Determination of the resistance to artificial weathering
EN 549:1995, Rubber materials for seals and diaphragms for gas appliances and gas equipment
EN 573-1:2005, Aluminium and aluminium alloys — Chemical composition and form of wrought products
— Part 1: Numerical designation system
EN 1057:2006, Copper and copper alloys Seamless, round copper tubes for water and gas in sanitary and
heating applications
5
---------------------- Page: 7 ----------------------
SIST EN 26:2015/oprA1:2016
EN 26:2015/prA1:2016 (E)
EN 1443:2003, Chimneys — General requirements
EN 1856-2:2009, Chimneys — Requirements for metal chimneys — Part 2: Metal flue liners and
connecting flue pipes
EN 10226-1:2004, Pipe threads where pressure tight joints are made on the threads — Part 1: Taper
external threads and parallel internal threads — Dimensions, tolerances and designation
EN 13203-1:2015, Gas-fired domestic appliances producing hot water — Appliances not exceding 70 kW
heat input and 300 l water storage capacity — Part 1: Assessment of performance of hot water deliveries
EN 13216-1:2005, Chimneys — Test methods for system chimneys — Part 1: General test methods
EN 13501-1:2007, Fire classification of construction products and building elements — Part 1:
Classification using data from reaction to fire tests
EN 14459:2008, Control functions in electronic systems for gas burners and gas burning appliances —
Methods for classification and assessment
EN 60335-2-102:2007, Household and similar electrical appliances — Safety — Part 2-102: Particular
requirements for gas, oil and solid-fuel burning appliances having electrical connections (IEC 60335-2-
102)
EN 60730-2-9:2013, Automatic electrical controls for household and similar use — Part 2-9: Particular
requirements for temperature sensing controls (IEC 60730-2-9)
EN ISO 178:2011, Plastics — Determination of flexural properties (ISO 178)
EN ISO 179-1:2010, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented
impact test (ISO 179-1)
EN ISO 228-1:2003, Pipe threads where pressure-tight joints are not made on the threads — Part 1:
Dimensions, tolerances and designation (ISO 228-1)
EN ISO 527-1:2012, Plastics — Determination of tensile propertie
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.