oSIST prEN 6046:2024
(Main)Aerospace series - Bearing, spherical, plain, in corrosion resisting steel - Narrow series - Dimensions and loads - Inch series
Aerospace series - Bearing, spherical, plain, in corrosion resisting steel - Narrow series - Dimensions and loads - Inch series
This document specifies the characteristics of inch based spherical plain bearing, metal to metal, in corrosion resisting steel, narrow series.
They are intended for use in fixed or moving parts of the aircraft structure and their control mechanisms.
They are used in the temperature range as determined by the grease capability as below:
- code A: greased as per MIL-PRF-23827 Type I, operating temperature range −73 °C to 121 °C;
- code B: greased as per MIL-PRF-81322, operating temperature range −54 °C to 177 °C.
The range of application for bearings lubricated with grease per code A is limited to 121 °C.
In both cases the spherical surface of the outer or inner ring are provided with a dry-film lubricant as per MIL-PRF-46010 or equivalent (anti-seizing protection).
The slide hole treatment either at the outer ring or inner ring.
Luft- und Raumfahrt - Gelenklager aus korrosionsbeständigem Stahl - Schmale Reihe - Maße und Belastungen - Inch-Reihe
Série aérospatiale - Rotule lisse en acier résistant à la corrosion - Série étroite - Dimensions et charges - Série en inches
Aeronavtika - Kroglični drsni ležaji iz korozijsko odpornega jekla - Ozki tip - Mere in obremenitve - Palčne mere
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 6046:2024
01-julij-2024
Aeronavtika - Kroglični drsni ležaji iz korozijsko odpornega jekla - Ozki tip - Mere
in obremenitve - Palčne mere
Aerospace series - Bearing, spherical, plain, in corrosion resisting steel - Narrow series -
Dimensions and loads - Inch series
Luft- und Raumfahrt - Gelenklager aus korrosionsbeständigem Stahl - Schmale Reihe -
Maße und Belastungen - Inch-Reihe
Série aérospatiale - Rotule lisse en acier résistant à la corrosion - Série étroite -
Dimensions et charges - Série en inches
Ta slovenski standard je istoveten z: prEN 6046
ICS:
21.100.01 Ležaji na splošno Bearings in general
49.035 Sestavni deli za letalsko in Components for aerospace
vesoljsko gradnjo construction
oSIST prEN 6046:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 6046:2024
---------------------- Page: 2 ----------------------
oSIST prEN 6046:2024
DRAFT
EUROPEAN STANDARD
prEN 6046
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2024
ICS 49.035 Will supersede EN 6046:2020
English Version
Aerospace series - Bearing, spherical, plain, in corrosion
resisting steel - Narrow series - Dimensions and loads -
Inch series
Série aérospatiale - Rotule lisse en acier résistant à la Luft- und Raumfahrt - Gelenklager aus
corrosion - Série étroite - Dimensions et charges - Série korrosionsbeständigem Stahl - Schmale Reihe - Maße
en inches und Belastungen - Inch-Reihe
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 6046:2024 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 6046:2024
prEN 6046:2024 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and symbols . 5
4 Requirements . 6
4.1 Configuration, dimensions, tolerances and mass . 6
4.2 Surface roughness . 6
4.3 Material . 6
4.4 Surface treatment .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.