iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 15522-2:2023/oprA1:2024

(Amendment)

Oil spill identification - Petroleum and petroleum related products - Part 2: Analytical method and interpretation of results based on GC-FID and GC-low resolution-MS analyses

Oil spill identification - Petroleum and petroleum related products - Part 2: Analytical method and interpretation of results based on GC-FID and GC-low resolution-MS analyses

This document specifies a method to identify and compare the compositional characteristics of oil samples. Specifically, it describes the detailed analytical and data processing methods for identifying the characteristics of spill samples and establishing their correlation to suspected source oils. Even when samples or data from suspected sources are not available for comparison, establishing the specific nature (e.g. refined petroleum, crude oil, waste oil, etc.) of the spilled oil still helps to constrain the possible source(s).
This methodology is restricted to petroleum related products containing a significant proportion of hydrocarbon-components with a boiling point above 150 °C. Examples are: crude oils, higher boiling condensates, diesel oils, residual bunker or heavy fuel oils, lubricants, and mixtures of bilge and sludge samples, as well as distillate fuels and blends. While the specific analytical methods are perhaps not appropriate for lower boiling oils (e.g. kerosene, jet fuel, or gasoline), the general concepts described in this methodology, i.e. statistical comparison of weathering-resistant diagnostic ratios, are applicable in spills involving these kinds of oils.
Paraffin based products (e.g. waxes, etc.) are outside the scope of this method because too many compounds are removed during the production process [37]. However, the method can be used to identify the type of product involved.
Although not directly intended for identifying oil recovered from groundwater, vegetation, wildlife/tissues, soil, or sediment matrices, they are not precluded. However, caution is needed as extractable compounds can be present in these matrices that alter and/or contribute additional compounds compared to the source sample. If unrecognized, the contribution from the matrix can lead to false “non-matches”. It is therefore advisable to analyse background sample(s) of the matrix that appear unoiled.
When analysing “non-oil” matrices additional sample preparation (e.g. clean-up) is often required prior to analysis and the extent to which the matrix affects the correlation achieved is to be considered. Whether the method is applicable for a specific matrix depends upon the oil concentration compared to the “matrix concentration”. In matrices containing high concentrations of oil, a positive match can still be concluded. In matrices containing lower concentrations of oil, a false “non-match” or an “inconclusive match” can result from matrix effects. Evaluation of possible matrix effects is beyond the scope of this document.

Identifizierung von Ölverschmutzungen - Rohöl und Mineralölerzeugnisse - Teil 2: Analytische Methodik und Interpretation der Ergebnisse, basierend auf GC-FID- und GC-MS-Analysen bei niedriger Auflösung

Identification des pollutions pétrolières - Pétrole et produits pétroliers - Partie 2 : Méthode d'analyse et interprétation des résultats sur la base des analyses par CPG DIF et CPG-SM faible résolution

Prepoznavanje razlitij olj - Nafta in sorodni naftni proizvodi - 2. del: Analizne metode in podajanje rezultatov, izhajajočih iz GC-FID in GC-MS nizke ločljivosti

General Information

Status
Not Published
Public Enquiry End Date
31-Mar-2024
ICS
13.020.40 - Pollution, pollution control and conservation
13.060.99 - Other standards related to water quality
75.080 - Petroleum products in general
Technical Committee
NAD - Petroleum products, lubricants and related products
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
31-Jan-2024
Due Date
19-Jun-2024
Ref Project
EN 15522-2:2023/prA1 - Oil spill identification - Petroleum and petroleum related products - Part 2: Analytical method and interpretation of results based on GC-FID and GC-low resolution-MS analyses

Relations

Amends
SIST EN 15522-2:2023 - Oil spill identification - Petroleum and petroleum related products - Part 2: Analytical method and interpretation of results based on GC-FID and GC-low resolution-MS analyses
Effective Date
01-Mar-2024

Buy Standard

EN 15522-2:2023/oprA1:2024EN 15522-2:2023/oprA1:2024
PreviousNext
Draft
EN 15522-2:2023/oprA1:2024
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 15522-2:2023/oprA1:2024
01-marec-2024
Prepoznavanje razlitij olj - Nafta in sorodni naftni proizvodi - 2. del: Analizne
metode in podajanje rezultatov, izhajajočih iz GC-FID in GC-MS nizke ločljivosti
Oil spill identification - Petroleum and petroleum related products - Part 2: Analytical
method and interpretation of results based on GC-FID and GC-low resolution-MS
analyses
Identifizierung von Ölverschmutzungen - Rohöl und Mineralölerzeugnisse - Teil 2:
Analytische Methodik und Interpretation der Ergebnisse, basierend auf GC-FID- und GC-
MS-Analysen bei niedriger Auflösung
Identification des pollutions pétrolières - Pétrole et produits pétroliers - Partie 2 :
Méthode d'analyse et interprétation des résultats sur la base des analyses par CPG DIF
et CPG-SM faible résolution
Ta slovenski standard je istoveten z: EN 15522-2:2023/prA1
ICS:
13.020.40 Onesnaževanje, nadzor nad Pollution, pollution control
onesnaževanjem in and conservation
ohranjanje
13.060.99 Drugi standardi v zvezi s Other standards related to
kakovostjo vode water quality
75.080 Naftni proizvodi na splošno Petroleum products in
general
SIST EN 15522-2:2023/oprA1:2024 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 15522-2:2023/oprA1:2024

---------------------- Page: 2 ----------------------
SIST EN 15522-2:2023/oprA1:2024


DRAFT
EUROPEAN STANDARD
EN 15522-2:2023
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
March 2024
ICS 13.020.40; 75.080
English Version

Oil spill identification - Petroleum and petroleum related
products - Part 2: Analytical method and interpretation of
results based on GC-FID and GC-low resolution-MS
analyses
Identification des pollutions pétrolières - Pétrole et Identifizierung von Ölverschmutzungen - Rohöl und
produits pétroliers - Partie 2 : Méthode d'analyse et Mineralölerzeugnisse - Teil 2: Analytische Methodik
interprétation des résultats sur la base des analyses und Interpretation der Ergebnisse, basierend auf GC-
par CPG DIF et CPG-SM faible résolution FID- und GC-MS-Analysen bei niedriger Auflösung
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 19.

This draft amendment A1, if approved, will modify the European Standard EN 15522-2:2023. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15522-2:2023/prA1:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 15522-2:2023/oprA1:2024
EN 15522-2:2023/prA1:2024 (E)
Contents Page
European foreword . 3
1 Modifications to Clause 1, “Scope” . 4
2 Modifications to Clause 3, "Terms and definitions" . 4
3 Modification to 5.2, "GC-FID and GC-MS analysis" . 5
4 Modifications to 6.3.3, "Oil samples from an Ethylene-tetrafluorethylene (ETFE) net" . 5
5 Modification to 6.4.5, "Silica or Florisil® column clean-up" .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 15522-1:2023(Main)
Oil spill identification - Petroleum and petroleum related products - Part 1: Sampling
EN 15522-1:2023

EN 15522-1 provides guidance on taking and handling samples, that are collected as part of an investigation into the likely source of a crude oil or petroleum product spill into a marine or aquatic environment. Guidance is given on taking samples from both the spill and its potential source.
Mostly, oil sampling is part of legal procedures and has to be treated like any other preservation of evidence (legal sampling). If samples are to be used in connection with legal proceedings, this document should be read in conjunction with any documents issued by the regulatory authorities in the country or countries in question where the spill has occurred.
Taking samples may involve hazardous materials, operations and equipment.
This document is not intended to address all the safety and health aspects associated with the guidance given. It is the responsibility of the user to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note: Most countries have special trained teams to take samples on board of ships. As police officer or law enforcer don’t take unnecessary risks and ask assistance from such a team when available.
For the sake of clarity, the word ‘oil’ is used throughout this document. It can equally refer to crude oil, a petroleum product or mixtures of such.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15522-2:2023(Main)
Oil spill identification - Petroleum and petroleum related products - Part 2: Analytical method and interpretation of results based on GC-FID and GC-low resolution-MS analyses
EN 15522-2:2023

This document specifies a method to identify and compare the compositional characteristics of oil
samples. Specifically, it describes the detailed analytical and data processing methods for identifying the
characteristics of spill samples and establishing their correlation to suspected source oils. Even when
samples or data from suspected sources are not available for comparison, establishing the specific nature
(e.g. refined petroleum, crude oil, waste oil, etc.) of the spilled oil still helps to constrain the possible
source(s).
This methodology is restricted to petroleum related products containing a significant proportion of
hydrocarbon-components with a boiling point above 150 °C. Examples are: crude oils, higher boiling
condensates, diesel oils, residual bunker or heavy fuel oils, lubricants, and mixtures of bilge and sludge
samples, as well as distillate fuels and blends. While the specific analytical methods are perhaps not
appropriate for lower boiling oils (e.g. kerosene, jet fuel, or gasoline), the general concepts described in
this methodology, i.e. statistical comparison of weathering-resistant diagnostic ratios, are applicable in
spills involving these kinds of oils.
Paraffin products (e.g. waxes, etc.) are outside the scope of this method because too many compounds
are removed during the production process [37] to correctly distinguish them from each other. However,
the method can be used to identify the type of product involved.
Although not directly intended for identifying oil recovered from groundwater, vegetation,
wildlife/tissues, soil, or sediment matrices, they are not precluded. However, caution is needed as
extractable compounds can be present in these matrices that alter and/or contribute additional
compounds compared to the source sample. If unrecognized, the contribution from the matrix can lead
to false “non-matches”. It is therefore advisable to analyse background sample(s) of the matrix that
appear unoiled.
When analysing “non-oil” matrices additional sample preparation (e.g. clean-up) is often required prior
to analysis and the extent to which the matrix affects the correlation achieved is to be considered.
Whether the method is applicable for a specific matrix depends upon the oil concentration compared to
the “matrix concentration”. In matrices containing high concentrations of oil, a positive match can still be
concluded. In matrices containing lower concentrations of oil, a false “non-match” or an “inconclusive
match” can result from matrix effects. Evaluation of possible matrix effects is beyond the scope of this
document.

  • Standard
    219 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    194 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15522-1:2023(Main)
Oil spill identification - Petroleum and petroleum related products - Part 1: Sampling
EN 15522-1:2023

EN 15522-1 provides guidance on taking and handling samples, that are collected as part of an investigation into the likely source of a crude oil or petroleum product spill into a marine or aquatic environment. Guidance is given on taking samples from both the spill and its potential source.
Mostly, oil sampling is part of legal procedures and has to be treated like any other preservation of evidence (legal sampling). If samples are to be used in connection with legal proceedings, this document should be read in conjunction with any documents issued by the regulatory authorities in the country or countries in question where the spill has occurred.
Taking samples may involve hazardous materials, operations and equipment.
This document is not intended to address all the safety and health aspects associated with the guidance given. It is the responsibility of the user to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note: Most countries have special trained teams to take samples on board of ships. As police officer or law enforcer don’t take unnecessary risks and ask assistance from such a team when available.
For the sake of clarity, the word ‘oil’ is used throughout this document. It can equally refer to crude oil, a petroleum product or mixtures of such.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15522-2:2023(Main)
Oil spill identification - Petroleum and petroleum related products - Part 2: Analytical method and interpretation of results based on GC-FID and GC-low resolution-MS analyses
EN 15522-2:2023

This document specifies a method to identify and compare the compositional characteristics of oil
samples. Specifically, it describes the detailed analytical and data processing methods for identifying the
characteristics of spill samples and establishing their correlation to suspected source oils. Even when
samples or data from suspected sources are not available for comparison, establishing the specific nature
(e.g. refined petroleum, crude oil, waste oil, etc.) of the spilled oil still helps to constrain the possible
source(s).
This methodology is restricted to petroleum related products containing a significant proportion of
hydrocarbon-components with a boiling point above 150 °C. Examples are: crude oils, higher boiling
condensates, diesel oils, residual bunker or heavy fuel oils, lubricants, and mixtures of bilge and sludge
samples, as well as distillate fuels and blends. While the specific analytical methods are perhaps not
appropriate for lower boiling oils (e.g. kerosene, jet fuel, or gasoline), the general concepts described in
this methodology, i.e. statistical comparison of weathering-resistant diagnostic ratios, are applicable in
spills involving these kinds of oils.
Paraffin products (e.g. waxes, etc.) are outside the scope of this method because too many compounds
are removed during the production process [37] to correctly distinguish them from each other. However,
the method can be used to identify the type of product involved.
Although not directly intended for identifying oil recovered from groundwater, vegetation,
wildlife/tissues, soil, or sediment matrices, they are not precluded. However, caution is needed as
extractable compounds can be present in these matrices that alter and/or contribute additional
compounds compared to the source sample. If unrecognized, the contribution from the matrix can lead
to false “non-matches”. It is therefore advisable to analyse background sample(s) of the matrix that
appear unoiled.
When analysing “non-oil” matrices additional sample preparation (e.g. clean-up) is often required prior
to analysis and the extent to which the matrix affects the correlation achieved is to be considered.
Whether the method is applicable for a specific matrix depends upon the oil concentration compared to
the “matrix concentration”. In matrices containing high concentrations of oil, a positive match can still be
concluded. In matrices containing lower concentrations of oil, a false “non-match” or an “inconclusive
match” can result from matrix effects. Evaluation of possible matrix effects is beyond the scope of this
document.

  • Standard
    219 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    194 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO/IEC 18045:2024(Main)
Information security, cybersecurity and privacy protection - Evaluation criteria for IT security - Methodology for IT security evaluation (ISO/IEC 18045:2022)
EN ISO/IEC 18045:2023

This document is a companion document to the "Evaluation criteria for IT security", ISO/IEC 15408 (all parts). This document defines the minimum actions to be performed by an evaluator in order to conduct an ISO/IEC 15408 Series evaluation, using the criteria and evaluation evidence defined in the ISO/IEC 15408 Series.

  • Standard
    439 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    436 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO/IEC 27005:2024(Main)
Information security, cybersecurity and privacy protection - Guidance on managing information security risks
ISO/IEC 27005:2022

This document provides guidance to assist organizations to:
— fulfil the requirements of ISO/IEC 27001 concerning actions to address information security risks;
— perform information security risk management activities, specifically information security risk assessment and treatment.
This document is applicable to all organizations, regardless of type, size or sector.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    62 pages
    English language
    sale 15% off
  • Standard
    66 pages
    French language
    sale 15% off
  • Draft
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17740:2024(Main)
Requirements for professional profiles related to personal data processing and protection
EN 17740:2023

The standard defines the requirements related to the professional activity of subjects active in the processing and protection of
personal data, namely the intellectual profession that is pursued at different levels of complexity and in different organizational
contexts, both public and private.
These requirements are specified, starting from the specific tasks and activities identified, in terms of knowledge, skills and
competence, in accordance with the European Qualifications Framework - EQF and are expressed in such a way as to facilitate and
contribute to harmonize, as far as possible, evaluation and validation processes of learning outcomes.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17799:2024(Main)
Personal data protection requirements for processing operations
EN 17799:2023

This document specifies baseline requirements for demonstrating compliance with the European personal data protection normative
framework in accordance with ISO/IEC 17065.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17905:2024(Main)
Intelligent transport systems - eSafety - eCall HLAP in hybrid circuit switched/packet switched network environments
EN 17905:2023

In respect of 112-eCall (pan-European eCall) (operating requirements defined in EN 16072), this document defines the additional high level application protocols, procedures and processes required to provide the eCall service whilst there are still both circuit switched and packet switched wireless communication networks in operation.
NOTE    The objective of implementing the pan-European in-vehicle emergency call system (eCall) is to automate the notification of a traffic accident, wherever in Europe, with the same technical standards and the same quality of services objectives by using a PLMN (such as ETSI prime medium) which supports the European harmonized 112/E112 emergency number (TS12 ETSI TS 122 003 or IMS packet switched network) and to provide a means of manually triggering the notification of an emergency incident.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17927:2024(Main)
Security Evaluation Standard for IoT Platforms (SESIP) - An effective methodology for applying cybersecurity assessment and re-use for connected products
EN 17927:2023

This document describes a cybersecurity evaluation methodology, named SESIP, for components of connected ICT products. Security claims in SESIP are made based on the security services offered by those components. Components can be in hardware and software. SESIP aims to support comparability between and reuse of independent security evaluations. SESIP provides a common set of requirements for the security functionality of components which apply to the foundational components of devices that are not application specific. The methodology describes the re-use of evaluation results.

  • Standard
    101 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    101 pages
    English language
    sale 10% off
    e-Library read for
    1 day