iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1993-1-5:2007/A1:2017

(Amendment)

Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements

Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements

DOP of 12 months!

Eurocode 3 - Bemessung und Konstruktion von Stahlbauten - Teil 1-5: Plattenförmige Bauteile

Eurocode 3 - Calcul des structures en acier - Partie 1-5: Plaques planes

Evrokod 3 - Projektiranje jeklenih konstrukcij - 1-5. del: Elementi pločevinaste konstrukcije

General Information

Status
Published
Public Enquiry End Date
19-Oct-2016
Publication Date
16-May-2017
ICS
91.010.30 - Technical aspects
91.080.13 - Steel structures
Technical Committee
KON - Structures
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
05-May-2017
Due Date
10-Jul-2017
Completion Date
17-May-2017
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
TP237 - Pravilnik o spodnjem ustroju železniških prog
Mandate
M/265 - Mandate to CEN for the conversion of the Eurocodes from ENV into EN concerning the structural and geotechnical design of buildings and civil engineering works
M/BC/CEN/89/11 - Framework mandate to CEN on Eurocode work : execution of a standardization programme on Eurocodes for the structural design of building and civil engineering works
Ref Project
EN 1993-1-5:2006/A1:2017 - Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements

Relations

Replaced By
SIST EN 1993-1-5:2024 - Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
Effective Date
01-Jul-2024
Amends
SIST EN 1993-1-5:2007 - Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
Effective Date
01-Jun-2017

Buy Standard

EN 1993-1-5:2007/A1:2017EN 1993-1-5:2007/A1:2017
PreviousNext
Amendment
EN 1993-1-5:2007/A1:2017
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
EN 1993-1-5:2007/oprA1:2016EN 1993-1-5:2007/oprA1:2016
PreviousNext
Draft
EN 1993-1-5:2007/oprA1:2016
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1993-1-5:2007/A1:2017
01-junij-2017
(YURNRG3URMHNWLUDQMHMHNOHQLKNRQVWUXNFLMGHO(OHPHQWLSORþHYLQDVWH
NRQVWUXNFLMH
Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
Eurocode 3 - Bemessung und Konstruktion von Stahlbauten - Teil 1-5: Plattenförmige
Bauteile
Eurocode 3 - Calcul des structures en acier - Partie 1-5: Plaques planes
Ta slovenski standard je istoveten z: EN 1993-1-5:2006/A1:2017
ICS:
91.010.30 7HKQLþQLYLGLNL Technical aspects
91.080.13 Jeklene konstrukcije Steel structures
SIST EN 1993-1-5:2007/A1:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1993-1-5:2007/A1:2017

---------------------- Page: 2 ----------------------

SIST EN 1993-1-5:2007/A1:2017


EN 1993-1-5:2006/A1
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2017
EUROPÄISCHE NORM
ICS 91.010.30; 91.080.13
English Version

Eurocode 3 - Design of steel structures - Part 1-5: Plated
structural elements
Eurocode 3 - Calcul des structures en acier - Partie 1-5 : Eurocode 3 - Bemessung und Konstruktion von
Plaques planes Stahlbauten - Teil 1-5: Plattenförmige Bauteile
This amendment A1 modifies the European Standard EN 1993-1-5:2006; it was approved by CEN on 17 January 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1993-1-5:2006/A1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1993-1-5:2007/A1:2017
EN 1993-1-5:2006/A1:2017 (E)
Contents Page
European foreword .
...

SLOVENSKI STANDARD
SIST EN 1993-1-5:2007/oprA1:2016
01-oktober-2016
(YURNRG3URMHNWLUDQMHMHNOHQLKNRQVWUXNFLMGHO(OHPHQWLSORþHYLQDVWH
NRQVWUXNFLMH
Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
Eurocode 3 - Bemessung und Konstruktion von Stahlbauten - Teil 1-5: Plattenförmige
Bauteile
Eurocode 3 - Calcul des structures en acier - Partie 1-5: Plaques planes
Ta slovenski standard je istoveten z: EN 1993-1-5:2006/prA1:2016
ICS:
91.010.30 7HKQLþQLYLGLNL Technical aspects
91.080.13 Jeklene konstrukcije Steel structures
SIST EN 1993-1-5:2007/oprA1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 1993-1-5:2007/oprA1:2016

---------------------- Page: 2 ----------------------
SIST EN 1993-1-5:2007/oprA1:2016


DRAFT
EUROPEAN STANDARD
EN 1993-1-5:2006
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
July 2016
ICS 91.010.30; 91.080.10
English Version

Eurocode 3 - Design of steel structures - Part 1-5: Plated
structural elements
Eurocode 3 - Calcul des structures en acier - Partie 1-5: Eurocode 3 - Bemessung und Konstruktion von
Plaques planes Stahlbauten - Teil 1-5: Plattenförmige Bauteile
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 250.

This draft amendment A1, if approved, will modify the European Standard EN 1993-1-5:2006. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review a
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1993-1-3:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-3: Cold-formed members and sheeting
EN 1993-1-3:2024

1.1   Scope of prEN 1993-1-3
(1) This document provides rules for structural design of cold-formed steel members and sheeting.
(2) This document applies to cold-formed steel products made from coated or uncoated hot- or cold-rolled sheet or strip, which have been cold-formed by processes such as roll-forming or press braking. It also covers sheeting and members which are curved during fabrication by continuous bending or roll-forming. Sheeting which has the curvature created by crushing the inner flanges is not included. This document is also applicable to the design of profiled steel sheeting for composite steel and concrete slabs at the construction stage, see EN 1994. The execution of steel structures made of cold-formed steel members and sheeting is covered in EN 1090 4. Provisions for bolted connections are provided in EN 1090 2.
NOTE   The rules in prEN 1993 1 3 complement the rules in other parts of EN 1993 1.
(3) Methods are also given for stressed-skin design, using steel sheeting as a structural diaphragm.
(4) This document does not apply to cold-formed circular and rectangular structural hollow sections supplied to EN 10219, for which reference is made to EN 1993 1 1 and EN 1993 1 8.
(5) This document provides methods for design by calculation and for design assisted by testing. The methods for design by calculation apply only within the stated ranges of material properties and geometric proportions, for which sufficient experience and test evidence is available. These limitations do not apply to design assisted by testing.
1.2   Assumptions
(1) Unless specifically stated, EN 1990, EN 1991 (all parts) and EN 1993 1 1 apply.
(2) The design methods given in prEN 1993 1 3 are applicable if:
-   the execution quality is as specified in EN 1090 4, the execution quality of bolted connections is as specified in EN 1090 2, and
-   the construction materials and products are as specified in the relevant parts of EN 1993 (all parts), or in the relevant material and product specifications.
(2) EN 1993 is intended to be used in conjunction with:
-   the parts of EN 1992 to EN 1999 where steel structures or steel components are referred to within those documents;
-   EN, EAD and ETA standards for construction products relevant to steel structures.

  • Standard
    209 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    208 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1993-1-5:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
EN 1993-1-5:2024

(1) EN 1993-1-5 gives design requirements of stiffened and unstiffened plates which are subject to inplane
forces.
(2) Effects due to shear lag, in-plane load introduction and plate buckling for I-section girders and box
girders are covered. Also covered are plated structural components subject to in-plane loads as in tanks and
silos. The effects of out-of-plane loading are outside the scope of this document.
NOTE 1: The rules in this part complement the rules for class 1, 2, 3 and 4 sections, see EN 1993-1-1.
NOTE 2: For the design of slender plates which are subject to repeated direct stress and/or shear and also
fatigue due to out-of-plane bending of plate elements (breathing) see EN 1993-2 and EN 1993-6.
NOTE 3: For the effects of out-of-plane loading and for the combination of in-plane effects and out-of-plane
loading effects see EN 1993-2 and EN 1993-1-7.
NOTE 4: Single plate elements may be considered as flat where the curvature radius r satisfies:
t
a
r
2
³ (1.1)
where a is the panel width
t is the plate thickness

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1993-1-2:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-2: Structural fire design
EN 1993-1-2:2024

1.1   Scope of prEN 1993-1-2
(1) This document provides rules for the design of steel structures for the accidental situation of fire exposure. This Part of EN 1993 only identifies differences from, or supplements to, normal temperature design.
(2) This document applies to steel structures required to fulfil a loadbearing function.
(3) This document does not include rules for separating function.
(4) This document gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned function and the levels of performance.
(5) This document applies to structures, or parts of structures, that are within the scope of EN 1993 1 1 and are designed accordingly.
(6) This document is intended to be used in conjunction with EN 1991-1-2, EN 1993-1-1, EN 1993 1-3, EN 1993-1-4, EN 1993-1-5, EN 1993-1-6, EN 1993-1-7, EN 1993-1-8, EN 1993-1-11, EN 1993-1-13 or EN 1993-1-14.
1.2   Assumptions
(1) Unless specifically stated, EN 1990, EN 1991(all parts) and EN 1993-1-1 apply.
(2) The design methods given in prEN 1993-1-2 are applicable if
-   the execution quality is as specified in EN 1090-2 and/or EN 1090-4, and
-   the construction materials and products used are as specified in prEN 1993-1-1:2020, Table 5.1 and Table 5.2 and in prEN 1993-1-3:2022, Table 5.1 and Table 5.2, or in the relevant material and product specifications.
(3) In addition to the general assumptions of EN 1990 the following assumptions apply:
-   the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation;
-   any fire protection measure taken into account in the design will be adequately maintained.

  • Standard
    97 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    91 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1993-1-13:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-13: Beams with large web openings
EN 1993-1-13:2024

1.1   Scope of prEN 1993-1-13
1.1.1   General
(1) This document gives supplementary provisions that extend the application of EN 1993-1-1 and EN 1993 1 5 to the design of rolled and welded steel sections with various shapes of web openings. The following cases are considered:
—   rolled or welded beams with widely spaced web openings;
—   rolled or welded beams with closely spaced web openings;
—   cellular beams with circular openings made by cutting and re-welding two parts of steel sections that may be different in dimensions;
—   beams with hexagonal and sinusoidal openings made by cutting and re-welding two parts of steel sections that may be different in dimensions.
(2) This document applies to uniform members with I or H profiles, which are symmetric about the weak axis. It does not apply to non-prismatic or curved beams although the same principles can apply.
(3) This document applies to steel beams with web openings that are subjected to sagging (positive) and to beams that are also subjected to hogging (negative) bending moments.
(4) This document covers the verification of the resistance at the openings and their effect on the global behaviour of the beam, including lateral torsional buckling.
(5) Alternative methods are presented for beams with circular openings and with sinusoidal openings in which the forces and resistances are calculated by increments around or along the openings and which are suitable for computer methods.
(6) This document applies to web slenderness, hw/tw, not exceeding 121ε. The local checks at and between adjacent openings apply to web slenderness up to this limit. Tension field action of plate girders is not part of the scope.
NOTE   The limit of 121ε corresponds to the section classification for a symmetric steel section and is used as a convenient limit for the application of this document, including asymmetric sections. The material parameter ε is defined in prEN 1993-1-1:2020, 5.2.5 (2).
(7) This document does not cover fatigue. In case of fatigue, EN 1993-1-9 applies.
(8) This document does not cover fire design. For the design in case of fire, EN 1993-1-2 applies.
(9) This document does not cover the buckling verification of members with web openings under axial force.
1.1.2   Shapes of openings
(1) The different shapes of openings that are considered in this document are shown in Figure 1.1.
Figure 1.1...
1.1.3   Stiffened openings
(1) This document also covers openings in the web of beams that are reinforced by longitudinal stiffeners and/or transverse stiffeners on one or both sides of the web, see Figure 1.2.
NOTE   The National Annex can give rules for alternative types of stiffener.
Figure 1.2...
1.2   Assumptions
(1) Unless specifically stated, EN 1990, EN 1991 (all parts) and EN 1993-1-1 apply.
(2) The design methods given in EN 1993-1-13 are applicable if
—   the execution quality is as specified in EN 1090-2, and
—   the construction materials and products used are as specified in the relevant parts of EN 1993 (all parts), or in the relevant material and product specifications.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1993-1-8:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-8: Joints
EN 1993-1-8:2024

1.1   Scope of EN 1993 1 8
(1) This document gives design methods for the design of joints subject to predominantly static loading using all steel grades from S235 up to and including S700 unless otherwise stated in individual clauses.
1.2   Assumptions
(1) The assumptions of EN 1990 and EN 1993-1-1 apply to this document.
(2) The design methods given in this part of EN 1993 are applicable when the quality of construction is as specified in EN 1090 2 or EN 1090 4, and that the construction materials and products used are those specified in the relevant parts of EN 1993, or in the relevant material and product specifications.

  • Standard
    216 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    197 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 1993-1-101:2023(Main)
Eurocode 3: Design of steel structures - Part 1-101: Alternative interaction method for members in bending and compression
CEN/TS 1993-1-101:2022

(1) This document provides an alternative method for the stability verification of steel members under compression axial force and bending moment, with reference to EN 1993 1 1.
NOTE   For the applicability of this document, see Clause 4.
(2) The method given in this document applies to uniform steel members with double symmetric cross-section under axial compression force and bi-axial bending.

  • Technical specification
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical specification
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1993-1-1:2023(Main)
Eurocode 3 - Design of steel structures - Part 1-1: General rules and rules for buildings
EN 1993-1-1:2022

1.1   Scope of EN 1993 1 1
(1) EN 1993 1 1 gives basic design rules for steel structures.
(2) It also gives supplementary provisions for the structural design of steel buildings. These supplementary provisions are indicated by the letter "B" after the paragraph number, thus (  )B.
1.2   Assumptions
(1) The assumptions of EN 1990 apply to EN 1993 1 1.
(2) EN 1993 is intended to be used in conjunction with EN 1990, EN 1991 (all parts), the parts of EN 1992 to EN 1999 where steel structures or steel components are referred to within those documents, EN 1090 2, EN 1090 4 and ENs, EADs and ETAs for construction products relevant to steel structures.

  • Standard
    120 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1993-1-4:2007/A2:2021(Amendment)
Eurocode 3 - Design of steel structures - Part 1-4: General rules - Supplementary rules for stainless steels
EN 1993-1-4:2006/A2:2020

DOP of 12 months

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1993-1-5:2007/A2:2019(Amendment)
Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
EN 1993-1-5:2006/A2:2019

EN 1993-1-5 gives design requirements of stiffened and unstiffened plates which are subject to inplane forces. Effects due to shear lag, in-plane load introduction and plate buckling for I-section girders and box girders are covered. Also covered are plated structural components subject to in-plane loads as in tanks and silos. The effects of out-of-plane loading are outside the scope of this document.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1993-1-6:2007/A1:2017(Amendment)
Eurocode 3 - Design of steel structures - Part 1-6: Strength and Stability of Shell Structures
EN 1993-1-6:2007/A1:2017

DOP of 12 months!

  • Amendment
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day