SIST EN ISO 11403-2:2004

Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2004)

ISO 11403-2:2004 specifies test procedures for the acquisition and presentation of multipoint data on the following thermal and processing properties of plastics:
enthalpy/temperature curve;
linear-expansion/temperature curve;
melt shear viscosity.

Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunktkennwerten - Teil 2: Thermische und Verarbeitungseigenschaften (ISO 11403-2:2004)

Dieser Teil der ISO 11403 legt Prüfverfahren für die Ermittlung und Darstellung von Vielpunktkennwerten für folgende thermische und Verarbeitungseigenschaften von Kunststoffen fest:
- Enthalpie-Temperatur-Diagramm;
- Längenausdehnung-Temperatur-Diagramm;
Schmelz-Scherviskosität.

Plastiques - Acquisition et présentation de données multiples comparables - Partie 2: Propriétés thermiques et caractéristiques relatives a la mise en oeuvre (ISO 11403-2:2004)

L'ISO 11403-2:2004 spécifie des modes opératoires d'essais en vue de l'acquisition et de la présentation des données multiples afférentes aux propriétés thermiques suivantes des plastiques et aux caractéristiques suivantes relatives à leur mise en oeuvre:
courbe enthalpie/température;
courbe dilatation linéique/température;
viscosité en cisaillement du matériau fondu.

Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih v različnih razmerah - 2. del: Toplotne lastnosti in predelavne lastnosti (ISO 11403-2:2004)

General Information

• Status: Withdrawn
• Publication Date: 30-Sep-2004
• Withdrawal Date: 08-Apr-2014
• ICS: 83.080.01 - Plastics in general
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 24-Mar-2014
• Due Date: 16-Apr-2014
• Completion Date: 09-Apr-2014
• Ref Project: EN ISO 11403-2:2004 - Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2004)

Relations

• Replaced By: SIST EN ISO 11403-2:2014 - Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012)
• Effective Date: 01-May-2014
• Replaced By: SIST EN ISO 11403-2:2014 - Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012)
• Effective Date: 08-Jun-2022
• Replaces: SIST EN ISO 11403-2:2000 - Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:1995)
• Effective Date: 01-Oct-2004

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11403-2:2004
01-oktober-2004
1DGRPHãþD
SIST EN ISO 11403-2:2000
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLKSRGDWNRYGREOMHQLKY
UD]OLþQLKUD]PHUDKGHO7RSORWQHODVWQRVWLLQSUHGHODYQHODVWQRVWL,62

Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal
and processing properties (ISO 11403-2:2004)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunktkennwerten - Teil
2: Thermische und Verarbeitungseigenschaften (ISO 11403-2:2004)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 2:
Propriétés thermiques et caractéristiques relatives a la mise en oeuvre (ISO 11403-
2:2004)
Ta slovenski standard je istoveten z: EN ISO 11403-2:2004
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11403-2:2004 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11403-2:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 11403-2:2004
EUROPEAN STANDARD
EN ISO 11403-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2004
ICS 83.080.01 Supersedes EN ISO 11403-2:1999
English version
Plastics - Acquisition and presentation of comparable multipoint
data - Part 2: Thermal and processing properties (ISO 11403-
2:2004)
Plastiques - Acquisition et présentation de données Kunststoffe - Ermittlung und Darstellung von
multiples comparables - Partie 2: Propriétés thermiques et vergleichbaren Vielpunktkennwerten - Teil 2: Thermische
caractéristiques relatives à la mise en oeuvre (ISO 11403- und Verarbeitungseigenschaften (ISO 11403-2:2004)
2:2004)
This European Standard was approved by CEN on 1 March 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11403-2:2004 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11403-2:2004
EN ISO 11403-2:2004 (E)
Foreword
This document (EN ISO 11403-2:2004) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by September 2004, and conflicting national
standards shall be withdrawn at the latest by September 2004.
This document supersedes EN ISO 11403-2:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 11403-2:2004 has been approved by CEN as EN ISO 11403-2:2004 without any
modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 11403-2:2004


INTERNATIONAL ISO
STANDARD 11403-2
Second edition
2004-03-15


Plastics — Acquisition and presentation
of comparable multipoint data —
Part 2:
Thermal and processing properties
Plastiques — Acquisition et présentation de données multiples
comparables —
Partie 2: Propriétés thermiques et caractéristiques relatives à la mise en
œuvre




Reference number
ISO 11403-2:2004(E)
©
ISO 2004

---------------------- Page: 5 ----------------------

SIST EN ISO 11403-2:2004
ISO 11403-2:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 11403-2:2004
ISO 11403-2:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Specimen preparation . 2
5 Conditioning . 2
6 Test requirements . 3
7 Presentation of data. 5
8 Precision . 6
Annex A (informative) Other properties . 7
Bibliography . 8

© ISO 2004 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 11403-2:2004
ISO 11403-2:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11403-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2, Mechanical
properties.
This second edition cancels and replaces the first edition (ISO 11403-2:1995), which has been technically
revised.
ISO 11403 consists of the following parts, under the general title Plastics — Acquisition and presentation of
comparable multipoint data:
 Part 1: Mechanical properties
 Part 2: Thermal and processing properties
 Part 3: Environmental influences on properties

iv © ISO 2004 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 11403-2:2004
ISO 11403-2:2004(E)
Introduction
This International Standard has been prepared because users of plastics find sometimes that available data
cannot be used readily to compare the properties of similar materials, especially when the data have been
supplied by different sources. Even when the same standard tests have been used, they often allow the
adoption of a wide range of alternative test conditions, and the data obtained are not necessarily comparable.
The purpose of this International Standard is to identify specific methods and conditions of test to be used for
the acquisition and presentation of data in order that valid comparisons between materials can be made.
ISO 10350 is concerned with single-point data. Such data represent the most basic method for characterizing
materials and are useful for the initial stages of material selection. The present International Standard
identifies test conditions and procedures for the measurement and presentation of a more substantial quantity
of data. Each property here is characterized by multipoint data which demonstrate how that property depends
upon important variables such as time, temperature and environmental effects. Additional properties are also
considered in this standard. These data therefore enable more discriminating decisions to be made regarding
a material’s suitability for a particular application. Some data are also considered adequate for undertaking
predictions of performance in service and of optimum processing conditions for moulding a component,
although it should be recognized that, for purposes of design, additional data will often be needed. One
reason for this is that some properties are strongly dependent upon the physical structure of the material. The
test procedures referred to in this standard employ, where possible, the multipurpose tensile bar, and the
polymer structure in this test specimen may be significantly different from that in specific regions of a moulded
component. Under these circumstances, therefore, the data will not be suitable for accurate design
calculations for product performance. The material supplier should be consulted for specific information on the
applicability of data.
ISO 10350 and the various parts of this International Standard together define the means for acquiring and
presenting a core set of comparable data for use in material selection. Use of these standards should result in
a rationalization of effort and a reduction of cost associated with provision of these data. Furthermore,
reference to these standards will simplify the development of data models for the computerized storage and
exchange of data concerning material properties.
Where appropriate, values for test variables have been specified by this standard. For some tests however,
owing to the wide range of conditions over which different plastics perform, the standard gives guidance in the
selection of certain test conditions so that they cover the operating range for that polymer. Because, in general,
the properties and performance specifications for different polymers differ widely, there is no obligation to
generate data under all the test conditions specified in this standard.
Data on a wide range of properties are needed to enable plastics to be selected and used in the large variety
of applications to which they are suited. ISO standards describe experimental procedures which are suitable
for the acquisition of relevant information on
...