Automatic electrical controls - Part 2-11: Particular requirements for energy regulators

IEC 60730-2-11:2019 is available as IEC 60730-2-11:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60730-2-11:2019 applies to energy regulators for use in, on, or in association with equipment, including energy regulators for heating, air conditioning and similar applications. The equipment may use electricity, gas, oil, solid fuel, solar thermal energy, etc. or a combination thereof.
This standard applies to the inherent safety, to the operating values, operating times and operating sequence where these are associated with equipment safety, and to the testing of automatic electrical energy regulator devices used in, or in association with, equipment.
This standard is also applicable to energy regulators for appliances within the scope of IEC 60335-1.
Throughout this standard the word “equipment” means “appliance and equipment”.
This standard also applies to automatic electrical energy regulators for equipment that may be used by the public, such as equipment intended to be used in shops, offices, hospitals, farms and commercial and industrial applications.
This standard does not apply to automatic electrical energy regulators designed exclusively for industrial process applications unless explicitly mentioned in the equipment standard.
This standard does not apply to equipment that are specifically within the scope of building automation equipment.
This standard is also applicable to individual energy regulators utilized as part of a control system or energy regulators which are mechanically integral with multi-functional controls having non-electrical outputs.
This standard applies to controls powered by primary or secondary batteries, requirements for which are contained within the standard, including Annex V
This third edition cancels and replaces the second edition published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) revision to the title to remove “for household and similar use”;
b) changes to the scope and related modifications;
c) changes to definitions in Annex H.
This Part 2-11 is intended to be used in conjunction with IEC 60730 1. It was established on the basis of the fifth edition of that standard (2013) including Amendment 1 (2015). Consideration may be given to future editions of, or amendments to, IEC 60730-1.
Keywords: Automatic Controls, Energy Regulators, Control Systems

Automatische elektrische Regel- und Steuergeräte – Teil 2-11: Besondere Anforderungen an Energieregler

Dispositifs de commande électrique automatiques - Partie 2-11: Règles particulières pour les régulateurs d'énergie

IEC 60730-2-11:2019 est disponible sous forme de IEC 60730-2-11:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.

IEC 60730-2-11:2019 s'applique aux régulateurs d'énergie destinés à être utilisés dans, sur ou avec du matériel, y compris les régulateurs d'énergie pour le chauffage, le conditionnement d'air et les applications analogues. Le matériel peut utiliser l'électricité, le gaz, le pétrole, des combustibles solides, l'énergie thermique solaire, etc. ou une combinaison de ces sources d'énergie.
La présente norme s'applique à la sécurité intrinsèque, aux valeurs de fonctionnement, aux temps de fonctionnement et aux séquences de fonctionnement, dans la mesure où ces éléments interviennent dans la sécurité du matériel, ainsi qu'aux essais des régulateurs d'énergie électriques automatiques utilisés dans ou avec du matériel.
La présente norme s'applique également aux régulateurs d'énergie pour appareils relevant du domaine d'application de l'IEC 60335-1.
Partout où il est utilisé dans la présente norme, le terme "matériel" signifie "appareil et équipement".
La présente norme s'applique également aux régulateurs d'énergie électriques automatiques pour les matériels qui peuvent être utilisés par le grand public, tels que les matériels destinés à être utilisés dans les magasins, bureaux, hôpitaux, exploitations agricoles, ainsi que les applications commerciales et industrielles.
La présente norme ne s'applique pas aux matériels qui relèvent spécifiquement du domaine d'application des matériels d'automatisation du bâtiment.
La présente norme s'applique également aux régulateurs d'énergie individuels utilisés comme élément d'un système de commande ou aux régulateurs d'énergie qui sont mécaniquement intégrés à des dispositifs de commande multifonctions dont les sorties ne sont pas électriques.
La présente norme s'applique aux dispositifs de commande alimentés par piles ou accumulateurs dont les exigences sont spécifiées dans la présente norme, notamment à l'Annexe V.
Cette troisième édition annule et remplace la deuxième édition parue en 2006. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) révision du titre pour supprimer “à usage domestique et analogue”;
b) modifications du domaine d’application et modifications associées;
c) modifications des définitions à l’Annexe H.
La présente Partie 2-11 est destinée à être utilisée conjointement avec l'IEC 60730 1. Elle a été établie sur la base de la cinquième édition de cette norme (2013) et de son Amendement 1 (2015). Les éditions futures de l'IEC 60730-1, ou ses amendements, pourront être pris en considération.
Mots-clés: Commande automatiques, régulateurs d'énergie, système de commande

Avtomatske električne krmilne naprave - 2-11. del: Posebne zahteve za regulatorje energije

General Information

Status
Published
Publication Date
03-May-2021
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Apr-2021
Due Date
20-Jun-2021
Completion Date
04-May-2021

Relations

Buy Standard

Standard
EN IEC 60730-2-11:2021
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60730-2-11:2021
01-junij-2021
Nadomešča:
SIST EN 60730-2-11:2008
Avtomatske električne krmilne naprave - 2-11. del: Posebne zahteve za regulatorje
energije
Automatic electrical controls - Part 2-11: Particular requirements for energy regulators
Dispositifs de commande électrique automatiques - Partie 2-11: Règles particulières
pour les régulateurs d'énergie
Ta slovenski standard je istoveten z: EN IEC 60730-2-11:2020
ICS:
97.120 Avtomatske krmilne naprave Automatic controls for
za dom household use
SIST EN IEC 60730-2-11:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60730-2-11:2021

---------------------- Page: 2 ----------------------
SIST EN IEC 60730-2-11:2021


EUROPEAN STANDARD EN IEC 60730-2-11

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2020
ICS 97.120 Supersedes EN 60730-2-11:2008 and all of its
amendments and corrigenda (if any)
English Version
Automatic electrical controls - Part 2-11: Particular requirements
for energy regulators
(IEC 60730-2-11:2019)
Dispositifs de commande électrique automatiques Partie 2- Automatische elektrische Regel- und Steuergeräte für den
11: Exigences particulières pour les régulateurs d'énergie Hausgebrauch und ähnliche Anwendungen - Teil 2-11:
(IEC 60730-2-11:2019) Besondere Anforderungen an Energieregler
(IEC 60730-2-11:2019)
This European Standard was approved by CENELEC on 2019-06-21. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60730-2-11:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60730-2-11:2021
EN IEC 60730-2-11:2020 (E)
European foreword
The text of document 72/1137/CDV, future edition 3 of IEC 60730-2-11, prepared by IEC/TC 72
"Automatic electrical controls" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60730-2-11:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-11-01
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-05-01
document have to be withdrawn

This document supersedes EN 60730-2-11:2008 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 60730-2-11:2019 was approved by CENELEC as a
European Standard without any modification.

2

---------------------- Page: 4 ----------------------
SIST EN IEC 60730-2-11:2021



IEC 60730-2-11

®


Edition 3.0 2019-05




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Automatic electrical controls

Part 2-11: Particular requirements for energy regulators




Dispositifs de commande électrique automatiques

Partie 2-11: Exigences particulières pour les régulateurs d'énergie
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 97.120 ISBN 978-2-8322-6877-3




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 5 ----------------------
SIST EN IEC 60730-2-11:2021
– 2 – IEC 60730-2-11:2019 © IEC 2019
CONTENTS
FOREWORD . 3
1 Scope and normative references . 5
2 Terms and definitions . 6
3 General requirements . 7
4 General notes on tests . 7
5 Rating. 7
6 Classification . 7
7 Information . 7
8 Protection against electric shock . 8
9 Provision for protective earthing . 8
10 Terminals and terminations . 8
11 Constructional requirements . 8
12 Moisture and dust resistance . 8
13 Electric strength and insulation resistance . 8
14 Heating . 8
15 Manufacturing deviation and drift . 9
16 Environmental stress . 9
17 Endurance . 9
18 Mechanical strength . 10
19 Threaded parts and connections . 11
20 Creepage distances, clearances and distances through solid insulation . 11
21 Resistance to heat, fire and tracking . 11
22 Resistance to corrosion . 11
23 Electromagnetic compatibility (EMC) requirements – Emission . 11
24 Components . 11
25 Normal operation . 11
26 Electromagnetic compatibility (EMC) requirements – Immunity . 11
27 Abnormal operation . 11
28 Guidance on the use of electronic disconnection . 11
Annex H (normative) Requirements for electronic controls . 12
Annex AA (normative) Regional differences . 15

---------------------- Page: 6 ----------------------
SIST EN IEC 60730-2-11:2021
IEC 60730-2-11:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________

AUTOMATIC ELECTRICAL CONTROLS

Part 2-11: Particular requirements for energy regulators

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment
declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60730-2-11 has been prepared by IEC technical committee 72:
Automatic electrical controls.
This third edition cancels and replaces the second edition published in 2006. This edition
constitutes a technical revision. This edition includes the following significant technical changes
with respect to the previous edition:
a) revision to the title to remove “for household and similar use”;
b) changes to the scope and related modifications;
c) changes to definitions in Annex H.
The text of this International Standard is based upon the following documents:
CDV Report on voting
72/1137/CDV 72/1167/RVC

Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 7 ----------------------
SIST EN IEC 60730-2-11:2021
– 4 – IEC 60730-2-11:2019 © IEC 2019
This Part 2-11 is intended to be used in conjunction with IEC 60730-1. It was established on
the basis of the fifth edition of that standard (2013) including Amendment 1 (2015).
Consideration may be given to future editions of, or amendments to, IEC 60730-1.
This Part 2-11 supplements or modifies the corresponding clauses in IEC 60730-1 so as to
convert that publication into the IEC standard: Particular requirements for energy regulators.
Where this Part 2-11 states "addition", "modification" or "replacement", the relevant requirement,
test specification or explanatory matter in Part 1 should be adapted accordingly.
Where no change is necessary, this Part 2-11 indicates that the relevant clause or subclause
applies.
In this publication, the following print types are used:
– requirements proper: in roman type,
– test specifications: in italic type,
– explanatory matter: in smaller roman type,
–  defined terms: bold type.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered
starting from 101.
A list of all parts of the IEC 60730 series, under the general title Automatic electrical controls,
can be found on the IEC website.
Future standards in this series will carry the new general title as cited above. Titles of existing
standards in this series will be updated at the time of the next edition.
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.

---------------------- Page: 8 ----------------------
SIST EN IEC 60730-2-11:2021
IEC 60730-2-11:2019 © IEC 2019 – 5 –
AUTOMATIC ELECTRICAL CONTROLS

Part 2-11: Particular requirements for energy regulators



1 Scope and normative references
This clause of Part 1 is applicable except as follows:
1.1 Scope
Replacement:
In general, this part of IEC 60730 applies to energy regulators for use in, on, or in association
with equipment, including energy regulators for heating, air conditioning and similar applications.
The equipment may use electricity, gas, oil, solid fuel, solar thermal energy, etc. or a
combination thereof.
NOTE These energy regulators can be thermally, mechanically or electrically operated.
This standard applies to the inherent safety, to the operating values, operating times and
operating sequence where these are associated with equipment safety, and to the testing of
automatic electrical energy regulator devices used in, or in association with, equipment.
This standard is also applicable to energy regulators for appliances within the scope of
IEC 60335-1.
Throughout this standard the word “equipment” means “appliance and equipment”.
This standard also applies to automatic electrical energy regulators for equipment that may be
used by the public, such as equipment intended to be used in shops, offices, hospitals, farms
and commercial and industrial applications.
This standard does not apply to automatic electrical energy regulators designed exclusively for
industrial
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.