Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005)

ISO 2505:2005 specifies a method for determining the longitudinal reversion of thermoplastics pipes, to be carried out in either a liquid or in air. In case of dispute, heated liquid is used as the reference. ISO 2505:2005 is applicable to all thermoplastics pipes with smooth internal and external walls of constant cross-section. It is not applicable to non-smooth structured-wall thermoplastics pipes.

Rohre aus Thermoplasten - Längsschrumpf - Prüfverfahren und Kennwerte (ISO 2505:2005)

Diese Internationale Norm legt ein Verfahren zur Bestimmung des Längsschrumpfes von Rohren aus Thermoplasten fest, deren Durchführung im Flüssigkeitsbad oder in Luft erfolgt. Im Schiedsfall ist das Verfahren im Flüssigkeitsbad als Referenzverfahren anzuwenden.
Diese Internationale Norm gilt für alle Rohre aus Thermoplasten mit glatten Innen- und Außenwänden mit konstantem Querschnitt. Sie gilt nicht für raue Rohre aus Thermoplasten mit strukturierten Wänden.
Die für den Rohrwerkstoff geeigneten Parameter sowie Empfehlungen für die maximalen Werte des Schrumpfes als Funktion des Rohrwerkstoffes sind in Anhang A angegeben.
ANMERKUNG      Die Messung des Längsschrumpfes wird für Rohre mit einer Wanddicke  16 mm als nicht relevant angesehen.

Tubes en matieres thermoplastiques - Retrait longitudinal a chaud - Méthode d'essai et parametres (ISO 2505:2005)

L'ISO 2505:2005 spécifie une méthode de détermination du retrait longitudinal à chaud des tubes en matières thermoplastiques, à réaliser soit dans un liquide, soit dans l'air. En cas de litige, la détermination à l'aide du liquide chauffé est la référence.
L'ISO 2505:2005 est applicable à tous les tubes en matières thermoplastiques à parois extérieure et intérieure lisses de section constante. Elle n'est pas applicable aux tubes en matières thermoplastiques à paroi structurée non lisse.

Plastomerne cevi –Dimenzijska stabilnost po segrevanju – Preskusna metoda in parametri (ISO 2505:2005)

General Information

Status
Withdrawn
Publication Date
31-Aug-2005
Withdrawal Date
12-Nov-2023
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
08-Nov-2023
Due Date
01-Dec-2023
Completion Date
13-Nov-2023

Relations

Buy Standard

Standard
EN ISO 2505:2005
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 2505:2005
01-september-2005
1DGRPHãþD
SIST EN 743:1997
Plastomerne cevi –Dimenzijska stabilnost po segrevanju – Preskusna metoda in
parametri (ISO 2505:2005)
Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO
2505:2005)
Rohre aus Thermoplasten - Längsschrumpf - Prüfverfahren und Kennwerte (ISO
2505:2005)
Tubes en matieres thermoplastiques - Retrait longitudinal a chaud - Méthode d'essai et
parametres (ISO 2505:2005)
Ta slovenski standard je istoveten z: EN ISO 2505:2005
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
SIST EN ISO 2505:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2505:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 2505:2005



EUROPEAN STANDARD
EN ISO 2505

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2005
ICS 23.040.20 Supersedes EN 743:1994
English version
Thermoplastics pipes - Longitudinal reversion - Test method and
parameters (ISO 2505:2005)
Tubes en matières thermoplastiques - Retrait longitudinal à Rohre aus Thermoplasten - Längsschrumpf - Prüfverfahren
chaud - Méthode d'essai et paramètres (ISO 2505:2005) und Kennwerte (ISO 2505:2005)
This European Standard was approved by CEN on 12 May 2005.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2505:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 2505:2005

EN ISO 2505:2005 (E)





Foreword


This document (EN ISO 2505:2005) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical
Committee CEN/TC 155 "Plastics piping systems and ducting systems", the secretariat of which
is held by NEN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by November 2005, and conflicting national
standards shall be withdrawn at the latest by November 2005.

This document supersedes EN 743:1994.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 2505:2005 has been approved by CEN as EN ISO 2505:2005 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 2505:2005

INTERNATIONAL ISO
STANDARD 2505
Second edition
2005-05-15


Thermoplastics pipes — Longitudinal
reversion — Test method and parameters
Tubes en matières thermoplastiques — Retrait longitudinal à chaud —
Méthode d'essai et paramètres





Reference number
ISO 2505:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST EN ISO 2505:2005
ISO 2505:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of th
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.