CEN/TC 337/WG 1 - Winter maintenance equipment

This document specifies the terminology and performance requirements for all sensor components of stationary equipment within a Road Weather Information System (RWIS).

This document specifies the test methods, the experimental set-up and result analysis for the laboratory qualification of stationary equipment within a RWIS.

This document specifies the essential requirements of stationary systems for production of brines for winter road maintenance and includes tests of these requirements. Installation boundary: chloride and water inlet to the saturator, brine outlet to the spreading machine. Within the scope are materials, brine storage and brine loading/unloading equipment also. Mobile systems for production of brines in situ are not content of this document.
The following points are not covered by this document:
-   System and construction requirements;
-   Requirements according to national and European legislations.

This document specifies the requirements on design and construction of bulk spreaders and sprayers, trailer spreaders and towed spreaders with speed related spreading for winter service. This document also deals with information about the minimum content required for operating manuals.
The document is valid for machines, which are used to spread the following spreading agents:
-   not pre-wetted and pre-wetted spreading agents;
-   abrasive spreading agents;
-   liquid spreading agents (brine).
This document is not applicable to:
-   requirements for registration and approval;
-   requirements made by automobile manufacturers;
-   requirements on safety, which are dealt with in FprEN 17106 1 and FprEN 17106 3 2.

This document gives the possibility to certify a model of vehicle-mounted or (trailer) dragged spreading machines for winter service with standard parameters, leaving the possibility to the manufacturer to evolve in performances. At the same time, information is given on the minimum content required for operating manuals.
This document is valid for machines which are used to spread the following media:
-   not pre-wetted spreading agent (solid spreading agent);
-   pre-wetted spreading agent;
-   liquid spreading agent (brine).
The following points are not covered by this document:
-   requirements for registration and approval;
-   requirements made by automobile manufacturers;
-   requirements on EN 15518 3.

This European Standard specifies the essential requirements of calcium chloride and magnesium chloride for spreading on roads for winter maintenance and includes tests of these requirements. The requirements are specified for calcium chloride and magnesium chloride in solid form and in water solution, which is delivered to the customer.

This European Standard specifies the essential requirements of sodium chloride (salt) for spreading on roads for winter maintenance and includes tests of these requirements. The requirements are specified for salt in crystallized form and for salt in solution (brine), which is delivered to the customer.

This Technical Specification defines general specifications and performance criteria of other solid and liquid de-icing agents than chlorides of sodium, calcium and magnesium, hereinafter referred to products, for the use in winter service on roads and on roads for specific uses, with the exception of runways and parking areas of aircrafts. It establishes the test methods to control them. The products include inorganic and organic de-icing agents, and mixtures of chlorides of sodium, calcium, magnesium and potassium with organic and inorganic components which are intended for special properties like inhibition of corrosion, enhanced melting capacity or improved spreading pattern.
NOTE   This Technical Specification defines specifications and performance criteria and offers for each a variation in the form of classes of requirements. This does not mean that there are products likely to respond to all the classes and criteria of the standard. Therefore, when defining the demand the user needs to make sure prior the appropriateness of his choice and the availability of suitable products.

This European Standard specifies requirements for snow removal machines with rotating tools for winter application on traffic areas. It is valid for design and construction. It also includes the minimum requirement concerning contents of the operating instructions.
This European Standard applies to:
   snow blowers;
   snow cutters;
   snow cutter blowers;
and related products such as side blowers, side cutters, etc.
This European Standard does not apply for:
   requirements for registration and approval;
   vehicle manufacturer requirements;
   safety requirements.

This document is valid for snow ploughs designed to be fitted to winter maintenance vehicles on their front-mounting plates according to EN 15432 and also for side-mounted snow ploughs.
Requirements regarding the testing of override security systems and/or bump security systems of front-mounted or side-mounted snow ploughs for winter service are determined by this document. This document is meant to assess the demands made on snow ploughs operated in traffic.
The document is valid for:
-   single-side snow ploughs;
-   variable V-ploughs.
The following points are not standardized by this document:
-   V-shaped snow ploughs;
-   requirements for registration and approval;
-   requirements made by carrier vehicle manufacturers;
-   requirements on safety – these are dealt with in EN 13021.

This European Standard defines the "Road Weather Information Systems" (RWIS) concept for public roads and traffic surfaces.
This standard applies to the acquisition of data on weather-related road and environment conditions as well as their forecast.
This information is typically used for road maintenance and can serve other systems like traffic management, road users information, data models, etc.

This European Standard specifies the frequency, resolution and content of road weather observation and forecast products for a Road Weather Information Systems (RWIS).

This document is valid for snow ploughs designed to be fitted to winter maintenance vehicles, on their frontmounting
plates according to EN 15432 and also for side-mounted snow ploughs.
Demands on design and construction of front-mounted or side-mounted snow ploughs for winter service are
determined by this document. This document is meant to assess the demands made on snow ploughs
operated in traffic.
The document is valid for:
single-side snow ploughs;
variable V-ploughs.
The following points are not standardized by this document:
v-shaped snow ploughs;
requirements for registration and approval;
requirements made by carrier vehicle manufacturers;
requirements on safety these are dealt with in EN 13021.

This standard constitutes a compilation of technical terms and definitions related to winter maintenance equipment.

This European Standard specifies the terminology and performance requirements for all components of stationary equipment within a Road Weather Information Systems (RWIS).

This Technical Specification specifies the test methods, the experimental set-up and result analysis for the laboratory qualification of stationary equipment within a RWIS.

Demands on design and construction of bulk spreaders, trailer spreaders and towed spreaders with speed related spreading for winter service are determined by this document. At the same time, information is given on the minimum content required for operating manuals.
The standard is valid for machines which are used to spread the following media:
a)   spreading agents with or without pre-wetted agent;
b)   abrasive spreading agents;
c)   brine.
The following points are not covered by this standard:
-   requirements for registration and approval;
-   requirements made by automobile manufacturers;
-   requirements on safety – these are dealt with in EN 13021.

This Technical Specification gives the possibility to certify a model of vehicle-mounted or (trailer-)dragged spreading machines for winter service with standard parameters, leaving the possibility for the manufacturer to evolve performance. At the same time, information is given on the minimum content required for operating manuals.
This Technical Specification is valid for machines which are used to spread the following media:
-   solid thawing media with or without pre-wetted media;
-   liquid thawing media.
The following points are not covered by this Technical Specification:
-   requirements for registration and approval;
-   requirements made by automobile manufacturers;
-   requirements on safety - these are dealt with in EN 13021.