ASTM D5967-07
(Test Method)Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
SIGNIFICANCE AND USE
p>This test method was developed to evaluate the viscometric performance of engine oils in turbocharged and intercooled four-cycle diesel engines. Results are obtained from used oil analysis.
The test method is used for engine oil specification acceptance when all details of the procedure are followed.
SCOPE
1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading). This test method is commonly referred to as the Mack T-8.
1.2 This test method also provides the procedure for running an extended length T-8 test, which is commonly referred to as the T-8E and an abbreviated length test, which is commonly referred to as T-8A. The procedures for the T-8E and the T-8A are identical to the T-8 with the exception of the items specifically listed in Annex A8 and Annex A9 respectively. Additionally, the procedure modifications listed in Annex A8 and Annex A9 refer to the corresponding section of the T-8 procedure.
1.3 The values stated in either SI or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are generally shown in parentheses when combined with SI units, and vice versa.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation:D5967–07
Standard Test Method for
1
Evaluation of Diesel Engine Oils in T-8 Diesel Engine
This standard is issued under the fixed designation D 5967; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
Scope 1
Referenced Documents 2
1.1 This test method covers an engine test procedure for
Terminology 3
evaluating diesel engine oils for performance characteristics,
Summary of Test Method 4
2
Significance and Use 5
includingviscosityincreaseandsootconcentrations(loading).
Apparatus 6
This test method is commonly referred to as the Mack T-8.
General Description 6.1
1.2 Thistestmethodalsoprovidestheprocedureforrunning
The Test Engine 6.2
Mack Test Engine 6.2.1
an extended length T-8 test, which is commonly referred to as
Engine Cooling System 6.2.2
the T-8E and an abbreviated length test, which is commonly
Engine Oil System 6.2.3
referred to as T-8A. The procedures for the T-8E and the T-8A Auxiliary Oil System 6.2.4
Crankcase Aspiration 6.2.5
are identical to the T-8 with the exception of the items
Blowby Meter 6.2.6
specifically listed in Annex A8 and Annex A9 respectively.
Air Supply and Filtration 6.2.7
Additionally, the procedure modifications listed in Annex A8 Fuel Supply 6.2.8
Intake Manifold Temperature Control 6.2.9
and Annex A9 refer to the corresponding section of the T-8
Engine Fluids 7
procedure.
Test Oil 7.1
1.3 The values stated in either SI or inch-pound units are to Test Fuel 7.2
Engine Coolant 7.3
be regarded separately as the standard. Within the text, the
Cleaning Materials 7.4
inch-pound units are generally shown in parentheses when
Preparation of Apparatus at Rebuild 8
combined with SI units, and vice versa. Cleaning of Parts 8.1
Valves, Seats, Guides, and Springs 8.2
1.4 This standard does not purport to address all of the
Cylinder Liner, Piston, and Piston Ring Assembly 8.3
safety concerns, if any, associated with its use. It is the
Injectors and Injection Pump 8.4
Assembly Instructions 8.5
responsibility of the user of this standard to establish appro-
Measurements 8.6
priate safety and health practices and determine the applica-
Laboratory and Engine Test Stand Calibration/Non-Reference 9
bility of regulatory limitations prior to use. See Annex A6 for
Requirements
Calibration Frequency 9.1
specific safety precautions.
Calibration Reference Oils 9.2
1.5 A Table of Contents follows:
Test Numbering 9.3
New Laboratories and New Test Stands 9.4
Calibrated Laboratories and Test Stands 9.5
1
This test method is under the jurisdiction of ASTM Committee D02 on Calibration Test Acceptance 9.6
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee Failing Calibration Tests 9.7
Non-Reference Oil Test Requirements 9.8
D02.B0.02 on Heavy Duty Engine Oils.
Procedure 10
Current edition approved Nov. 1, 2007. Published December 2007. Originally
Pretest Procedure 10.1
approved in 1996. Last previous edition approved in 2005 as D 5967–05.
2
Engine Start-Up 10.2
The ASTM Test Monitoring Center will update changes in this test method by
Engine Shutdown 10.3
means of Information Letters. This edition incorporates revisions contained in all
Test Cycle 10.4
information letters through 07–1. Information letters may be obtained from the
Oil Addition/Drain 10.5
ASTM Test Monitoring Center, 6555 Penn Avenue, Pittsburgh, PA 15206-4489,
Oil Samples 10.6
Attention: Administrator.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D5967–07
D 2500 Test Method for Cloud Point of Petroleum Products
Oil Consumption Calculations 10.7
Fuel Samples 10.8
D 2622 Test Method for Sulfur in Petroleum Products by
Periodic Measurements 10.9
Wavelength Dispersive X-ray Fluorescence Spectrometry
Blowby 10.10
D 2709 Test Method for Water and Sediment in Middle
Centrifugal Oil Filter Mass Gain 10.11
Oil Filter DP Calculation 10.12
Distillate Fuels by Centrifuge
Post Test 10.13
D 4052 Test Method for Density and Relative Density of
Inspection of Fuel and Oil During Test 11
Liquids by Digital Density Meter
Oil Inspection 11.1
Fuel Inspections 11.2
D 4175 Terminology Relating to Petroleum, Petroleum
Oil Consumption 11.3
Products, and Lubricants
Report 12
Reporting Test Results 12.1 D 4294 Test Method for Sulfur in Petroleum and Petroleum
Deviations from Test Operational Limits 12.2
Products by Energy-Dispersive X-ray Fluorescence Spec-
Electronic Transmission of Test Results 12.3
trometry
Plots of Operational Data 12.4
Precision and B
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D5967–05 Designation:D5967–07
Standard Test Method for
1
Evaluation of Diesel Engine Oils in T-8 Diesel Engine
This standard is issued under the fixed designation D 5967; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including
2
viscosity increase and soot concentrations (loading). This test method is commonly referred to as the Mack T-8.
1.2 This test method also provides the procedure for running an extended length T-8 test, which is commonly referred to as the
T-8Eandanabbreviatedlengthtest,whichiscommonlyreferredtoasT-8A.TheproceduresfortheT-8EandtheT-8Aareidentical
to the T-8 with the exception of the items specifically listed in Annex A8 and Annex A9 respectively. Additionally, the procedure
modifications listed in Annex A8 and Annex A9 refer to the corresponding section of the T-8 procedure.
1.3 The values stated in either SI or inch-pound units are to be regarded separately as the standard. Within the text, the
inch-pound units are generally shown in parentheses when combined with SI units, and vice versa.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. See Annex A6 for specific safety precautions.
1.5 A Table of Contents follows:
Scope 1
Referenced Documents 2
Terminology 3
Summary of Test Method 4
Significance and Use 5
Apparatus 6
General Description 6.1
The Test Engine 6.2
Mack Test Engine 6.2.1
Engine Cooling System 6.2.2
Engine Oil System 6.2.3
Auxiliary Oil System 6.2.4
Crankcase Aspiration 6.2.5
Blowby Meter 6.2.6
Air Supply and Filtration 6.2.7
Fuel Supply 6.2.8
Intake Manifold Temperature Control 6.2.9
Engine Fluids 7
Test Oil 7.1
Test Fuel 7.2
Engine Coolant 7.3
Cleaning Materials 7.4
Preparation of Apparatus at Rebuild 8
Cleaning of Parts 8.1
Valves, Seats, Guides, and Springs 8.2
Cylinder Liner, Piston, and Piston Ring Assembly 8.3
Injectors and Injection Pump 8.4
Assembly Instructions 8.5
Measurements 8.6
Laboratory and Engine Test Stand Calibration/Non-Reference 9
Requirements
Calibration Frequency 9.1
Calibration Reference Oils 9.2
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.B0.02
on Automotive Lubricants. Heavy Duty Engine Oils.
Current edition approved Nov. 1, 2005.2007. Published November 2005.December 2007. Originally approved in 1996. Last previous edition approved in 20042005 as
D 5967–045.
2
The ASTM Test Monitoring Center will update changes in this test method by means of Information Letters. This edition incorporates revisions contained in all
informationlettersthrough05–1.07–1.InformationlettersmaybeobtainedfromtheASTMTestMonitoringCenter,6555PennAvenue,Pittsburgh,PA15206-4489,Attention:
Administrator.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D5967–07
Test Numbering 9.3
New Laboratories and New Test Stands 9.4
Calibrated Laboratories and Test Stands 9.5
Calibration Test Acceptance 9.6
Failing Calibration Tests 9.7
Non-Reference Oil Test Requirements 9.8
Procedure 10
Pretest Procedure 10.1
Engine Start-Up 10.2
Engine Shutdown 10.3
Test Cycle 10.4
Oil Addition/Drain 10.5
Oil Samples 10.6
Oil Consumption Calculations 10.7
Fuel Samples 10.8
Periodic Measurements 10.9
Blowby 10.10
Centrifugal Oil Filter Mass Gain 10.11
Oil Filter DP Calculation 10.12
Post Test 10.13
Inspection of Fuel and Oil During Test 11
Oil Inspection 11.1
Fuel Inspections 11.2
Oil Consumption 11.3
Report 12
Reporting Test Results 12.1
Deviations from Test Operational Limits 12.2
Electronic Transmission of Test Results 12.3
Plots of Operational Data 12.4
Precision and Bias 13
Precision 13.1
Bias 13.2
Keywords 14
Annexes
Report Forms Annex A1
Sensor Locations Annex A2
Kinematic Viscosity At 100°C For Test Method D 5967 Samples Annex A3
Enhanced Thermal Gravimetric Analysis (TGA) Pro
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.